zephyr/boards/nxp/mimxrt1040_evk/mimxrt1040_evk.yaml

#
# Copyright 2023 NXP
#
# SPDX-License-Identifier: Apache-2.0
#

identifier: mimxrt1040_evk
name: NXP MIMXRT1040-EVK
type: mcu
arch: arm
toolchain:
  - zephyr
  - gnuarmemb
  - xtools
ram: 32768
flash: 8192
supported:
  - arduino_gpio
  - gpio
  - pwm
  - adc
  - spi
  - i2c
vendor: nxp
boards: arm: mixmrt1040_evk: add RT1040-EVK board Add RT1040 EVK board definition. This board port currently enables UART and GPIO only. Programming is supported by JLink host tools. Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com> 2023-02-20 18:10:58 +01:00			`#`
			`# Copyright 2023 NXP`
			`#`
			`# SPDX-License-Identifier: Apache-2.0`
			`#`

			`identifier: mimxrt1040_evk`
			`name: NXP MIMXRT1040-EVK`
			`type: mcu`
			`arch: arm`
			`toolchain:`
			`- zephyr`
			`- gnuarmemb`
			`- xtools`
			`ram: 32768`
			`flash: 8192`
			`supported:`
			`- arduino_gpio`
			`- gpio`
boards: arm: mimxrt1040: enabled PWM Enabled PWM output on J16.6, using tests/drivers/pwm/pwm_api. This board does not connect a PWM output to an LED, so only the PWM testcase was verified to function. Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com> 2023-02-20 20:10:00 +01:00			`- pwm`
boards: arm: mimxrt1040_evk: enable ADC support Enable ADC support for RT1040 EVK. Tested using samples/drivers/adc, using channels 3 and 4 of ADC0. Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com> 2023-02-20 22:07:04 +01:00			`- adc`
boards: arm: mixmrt1040_evk: enable SPI support Add support for SPI on RT1040 EVK, tested using tests/drivers/spi/spi_loopback sample. Transfers are enabled using DMA mode, with LPSPI1. Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com> 2023-02-21 02:32:52 +01:00			`- spi`
boards: arm: mixmrt1040_evk: enable RT1040 EVK I2C support Enable support for RT1040 EVK. This support was verified using the I2C target test. Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com> 2023-02-21 22:15:17 +01:00			`- i2c`
boards: add vendor to board yaml This is coming from devicetree and corrosponds to what we have in the dts/bindings/vendor-prefixes.txt file. This will allow for static filtering, especially with twister, i.e. no need to build anything to know the vendor of a board All of the vendor data was extracted automatically from the devicetree, so some platforms might not have the right vendor or no vendor at all right now, we need to fix some of the DTS information or do this manually to get this 100% correct. But we are close. Signed-off-by: Anas Nashif <anas.nashif@intel.com> 2023-06-22 20:47:45 +02:00			`vendor: nxp`