boards: add new board Electronut-labs Blip

Added config for https://github.com/electronut/ElectronutLabs-blip/

Signed-off-by: Tavish Naruka <tavishnaruka@gmail.com>

boards/arm/nrf52840_blip/Kconfig

@@ -0,0 +1,14 @@
+# Kconfig - Electronut Labs Blip board configuration
+#
+# Copyright (c) 2018 Electronut Labs
+#
+# SPDX-License-Identifier: Apache-2.0
+
+if BOARD_NRF52840_BLIP
+
+config BOARD_ENABLE_DCDC
+        bool "Enable DCDC mode"
+        select SOC_DCDC_NRF52X
+        default y
+
+endif # BOARD_NRF52840_BLIP

boards/arm/nrf52840_blip/Kconfig.board

@@ -0,0 +1,9 @@
+# Kconfig - Electronut Labs Blip board configuration
+#
+# Copyright (c) 2018 Electronut Labs
+#
+# SPDX-License-Identifier: Apache-2.0
+
+config  BOARD_NRF52840_BLIP
+	bool "Electronut Labs Blip"
+	depends on SOC_NRF52840_QIAA

boards/arm/nrf52840_blip/Kconfig.defconfig

@@ -0,0 +1,29 @@
+# Kconfig - Electronut Labs Blip board configuration
+#
+# Copyright (c) 2018 Electronut Labs
+#
+# SPDX-License-Identifier: Apache-2.0
+
+if BOARD_NRF52840_BLIP
+
+config BOARD
+	default "nrf52840_blip"
+
+if USB
+
+config USB_NRF52840
+	default y
+
+config USB_DEVICE_STACK
+	default y
+
+endif # USB
+
+if IEEE802154
+
+config IEEE802154_NRF5
+	default y
+
+endif # IEEE802154
+
+endif # BOARD_NRF52840_BLIP

boards/arm/nrf52840_blip/board.cmake

@@ -0,0 +1 @@
+include(${ZEPHYR_BASE}/boards/common/blackmagicprobe.board.cmake)

boards/arm/nrf52840_blip/doc/nrf52840_blip.rst

@@ -0,0 +1,198 @@
+.. _nrf52840_blip:
+
+Electronut Labs Blip
+####################
+
+Overview
+********
+
+Zephyr applications use the nrf52840_blip board configuration
+to run on Electronut Labs Blip hardware. It provides
+support for the Nordic Semiconductor nRF52840 ARM Cortex-M4F CPU and
+the following devices:
+
+* :abbr:`ADC (Analog to Digital Converter)`
+* CLOCK
+* FLASH
+* :abbr:`GPIO (General Purpose Input Output)`
+* :abbr:`I2C (Inter-Integrated Circuit)`
+* :abbr:`MPU (Memory Protection Unit)`
+* :abbr:`NVIC (Nested Vectored Interrupt Controller)`
+* :abbr:`PWM (Pulse Width Modulation)`
+* RADIO (Bluetooth Low Energy and 802.15.4)
+* :abbr:`RTC (nRF RTC System Clock)`
+* Segger RTT (RTT Console)
+* :abbr:`SPI (Serial Peripheral Interface)`
+* :abbr:`UART (Universal asynchronous receiver-transmitter)`
+* :abbr:`USB (Universal Serial Bus)`
+* :abbr:`WDT (Watchdog Timer)`
+
+.. figure:: img/nrf52840_blip.jpg
+     :width: 442px
+     :align: center
+     :alt: Electronut Labs Blip
+
+     Electronut Labs Blip (Credit: Electronut Labs)
+
+More information about the board is available at https://github.com/electronut/ElectronutLabs-blip.
+
+Hardware
+********
+
+Blip has two external oscillators. The frequency of
+the slow clock is 32.768 kHz. The frequency of the main clock
+is 32 MHz.
+
+Supported Features
+==================
+
+The nrf52840_blip board configuration supports the following
+hardware features currently:
+
++-----------+------------+----------------------+
+| Interface | Controller | Driver/Component     |
++===========+============+======================+
+| ADC       | on-chip    | adc                  |
++-----------+------------+----------------------+
+| CLOCK     | on-chip    | clock_control        |
++-----------+------------+----------------------+
+| FLASH     | on-chip    | flash                |
++-----------+------------+----------------------+
+| GPIO      | on-chip    | gpio                 |
++-----------+------------+----------------------+
+| I2C(M)    | on-chip    | i2c                  |
++-----------+------------+----------------------+
+| MPU       | on-chip    | arch/arm             |
++-----------+------------+----------------------+
+| NVIC      | on-chip    | arch/arm             |
++-----------+------------+----------------------+
+| PWM       | on-chip    | pwm                  |
++-----------+------------+----------------------+
+| RADIO     | on-chip    | Bluetooth,           |
+|           |            | ieee802154           |
++-----------+------------+----------------------+
+| RTC       | on-chip    | system clock         |
++-----------+------------+----------------------+
+| RTT       | Segger     | console              |
++-----------+------------+----------------------+
+| SPI(M/S)  | on-chip    | spi                  |
++-----------+------------+----------------------+
+| UART      | on-chip    | serial               |
++-----------+------------+----------------------+
+| USB       | on-chip    | usb                  |
++-----------+------------+----------------------+
+| WDT       | on-chip    | watchdog             |
++-----------+------------+----------------------+
+
+Connections and IOs
+===================
+
+LED
+---
+
+* LED1 (green) = P0.13
+* LED2 (green) = P0.14
+* LED3 (green) = P0.15
+
+Push buttons
+------------
+
+* BUTTON1 = SW1 = P1.07
+* Reset = SW5 = P0.18 (can be used as GPIO also)
+
+UART
+----
+
+BMP does not support hardware flow control, so only RX/TX pins are connected.
+
+* TX = P0.6
+* RX = P0.8
+
+I2C
+---
+
+I2C pins connected to onboard sensors:
+
+* SDA = P0.12
+* SCL = P0.11
+
+SPI
+---
+
+* SCK = P0.25
+* MOSI = P1.02
+* MISO = P0.24
+
+Microsd is connected to these pins, and CS pin is connected to P0.17.
+
+Programming and Debugging
+*************************
+
+Applications for the ``nrf52840_blip`` board configuration can be
+built and flashed in the usual way (see :ref:`build_an_application`
+and :ref:`application_run` for more details); The onboard Black Magic
+Probe debugger presents itself as two USB-serial ports. On Linux,
+they may come up as ``/dev/ttyACM0`` and ``/dev/ttyACM1``. The first
+one of these (``/dev/ttyACM0`` here) is the debugger port.
+GDB can directly connect to this port without requiring a GDB server by specifying
+``target external /dev/ttyACM0``. The second port acts as a
+serial port, connected to the SoC.
+
+Flashing
+========
+
+Applications are flashed and run as usual (see :ref:`build_an_application` and
+:ref:`application_run` for more details).
+
+Here is an example for the :ref:`hello_world` application.
+
+First, run your favorite terminal program to listen for output.
+
+.. code-block:: console
+
+   $ minicom -D <tty_device> -b 115200
+
+Replace :code:`<tty_device>` with the serial port of Black Magic Probe.
+For example, under Linux, :code:`/dev/ttyACM1`.
+
+Then build and flash the application in the usual way.
+
+.. zephyr-app-commands::
+   :zephyr-app: samples/hello_world
+   :board: nrf52840_blip
+   :goals: build flash
+
+Debugging
+=========
+
+Debug and attach configurations are available using Black Magic Probe, and
+``ninja debug``, or ``ninja attach`` (or with ``make``) are available.
+
+NOTE: You may need to press the reset button once after using ``ninja flash``
+to start executing the code. (not required with ``debug`` or ``attach``)
+
+
+Testing the LEDs and buttons in the nRF52840 PDK
+************************************************
+
+There are 2 samples that allow you to test that the buttons (switches) and LEDs on
+the board are working properly with Zephyr:
+
+* :ref:`blinky-sample`
+* :ref:`button-sample`
+
+You can build and flash the examples to make sure Zephyr is running correctly on
+your board. The button and LED definitions can be found in :file:`boards/arm/nrf52840_blip/nrf52840_blip.dts`.
+
+
+References
+**********
+
+.. target-notes::
+
+.. _Electronut Labs website: https://electronut.in
+.. _Store link: https://www.tindie.com/stores/ElectronutLabs/
+.. _Blip website: https://github.com/electronut/ElectronutLabs-blip
+.. _Schematic: https://github.com/electronut/ElectronutLabs-blip/blob/master/blip_v0.3_schematic.pdf
+.. _Nordic Semiconductor Infocenter: http://infocenter.nordicsemi.com/
+.. _Black Magic Probe website: https://github.com/blacksphere/blackmagic

boards/arm/nrf52840_blip/nrf52840_blip.dts

@@ -0,0 +1,161 @@
+/*
+ * Copyright (c) 2017 Linaro Limited
+ *
+ * Based on nrf52840_pca10056.dts
+ * modified 2018 Tavish Naruka <tavishnaruka@gmail.com>
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+/dts-v1/;
+#include <nordic/nrf52840_qiaa.dtsi>
+
+/ {
+	model = "Electronut Labs Blip";
+	compatible = "nordic,pca10056-dk", "nordic,nrf52840-qiaa",
+		     "nordic,nrf52840";
+
+	chosen {
+		zephyr,console = &uart0;
+		zephyr,shell-uart = &uart0;
+		zephyr,uart-mcumgr = &uart0;
+		zephyr,sram = &sram0;
+		zephyr,flash = &flash0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led0: led_0 {
+			gpios = <&gpio0 13 GPIO_INT_ACTIVE_LOW>;
+			label = "Green LED 0";
+		};
+		led1: led_1 {
+			gpios = <&gpio0 14 GPIO_INT_ACTIVE_LOW>;
+			label = "Red LED 1";
+		};
+		led2: led_2 {
+			gpios = <&gpio0 15 GPIO_INT_ACTIVE_LOW>;
+			label = "Blue LED 2";
+		};
+	};
+
+	buttons {
+		compatible = "gpio-keys";
+		button0: button_0 {
+			gpios = <&gpio1 7 GPIO_PUD_PULL_UP>;
+			label = "Push button switch 0";
+		};
+	};
+
+	/* These aliases are provided for compatibility with samples */
+	aliases {
+		led0 = &led0;
+		led1 = &led1;
+		led2 = &led2;
+		sw0 = &button0;
+	};
+};
+
+&adc {
+	status ="ok";
+};
+
+&gpiote {
+	status ="ok";
+};
+
+&gpio0 {
+	status ="ok";
+};
+
+&gpio1 {
+	status ="ok";
+};
+
+&uart0 {
+	compatible = "nordic,nrf-uart";
+	current-speed = <115200>;
+	status = "ok";
+	tx-pin = <6>;
+	rx-pin = <8>;
+	rts-pin = <5>;
+	cts-pin = <7>;
+};
+
+&i2c0 {
+	status = "ok";
+	sda-pin = <12>;
+	scl-pin = <11>;
+};
+
+&i2c1 {
+	status = "ok";
+	sda-pin = <2>;
+	scl-pin = <3>;
+};
+
+&spi0 {
+	status = "ok";
+	sck-pin = <25>;
+	mosi-pin = <34>;
+	miso-pin = <24>;
+};
+
+&spi1 {
+	status = "ok";
+	sck-pin = <19>;
+	mosi-pin = <20>;
+	miso-pin = <21>;
+};
+
+&spi2 {
+	status = "ok";
+	sck-pin = <26>;
+	mosi-pin = <23>;
+	miso-pin = <27>;
+};
+
+&spi3 {
+	status = "ok";
+	sck-pin = <29>;
+	mosi-pin = <30>;
+	miso-pin = <31>;
+};
+
+&flash0 {
+	/*
+	 * For more information, see:
+	 * http://docs.zephyrproject.org/latest/devices/dts/flash_partitions.html
+	 */
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		boot_partition: partition@0 {
+			label = "mcuboot";
+			reg = <0x000000000 0x0000C000>;
+		};
+		slot0_partition: partition@c000 {
+			label = "image-0";
+			reg = <0x0000C000 0x000069000>;
+		};
+		slot1_partition: partition@75000 {
+			label = "image-1";
+			reg = <0x00075000 0x000069000>;
+		};
+		scratch_partition: partition@de000 {
+			label = "image-scratch";
+			reg = <0x000de000 0x0001e000>;
+		};
+		storage_partition: partition@fc000 {
+			label = "storage";
+			reg = <0x000fc000 0x00004000>;
+		};
+	};
+};
+
+&usbd {
+	compatible = "nordic,nrf-usbd";
+	status = "ok";
+};

boards/arm/nrf52840_blip/nrf52840_blip.yaml

@@ -0,0 +1,12 @@
+identifier: nrf52840_blip
+name: Electronut Labs Blip
+type: mcu
+arch: arm
+toolchain:
+  - zephyr
+  - gnuarmemb
+supported:
+  - adc
+  - usb_device
+  - ble
+  - ieee802154

boards/arm/nrf52840_blip/nrf52840_blip_defconfig

@@ -0,0 +1,24 @@
+CONFIG_ARM=y
+CONFIG_SOC_FAMILY_NRF=y
+CONFIG_SOC_SERIES_NRF52X=y
+CONFIG_SOC_NRF52840_QIAA=y
+CONFIG_BOARD_NRF52840_BLIP=y
+
+# Enable MPU
+CONFIG_ARM_MPU=y
+
+# enable uart driver
+CONFIG_SERIAL=y
+CONFIG_UART_NRFX=y
+CONFIG_UART_0_NRF_UART=y
+
+# enable console
+CONFIG_CONSOLE=y
+CONFIG_UART_CONSOLE=y
+
+# additional board options
+CONFIG_GPIO_AS_PINRESET=y
+
+# bluetooth
+CONFIG_BT=y
+CONFIG_BT_CTLR=y

tests/drivers/adc/adc_api/src/test_adc.c

@@ -31,7 +31,8 @@
 #define ADC_2ND_CHANNEL_INPUT	NRF_ADC_CONFIG_INPUT_3
 
 #elif defined(CONFIG_BOARD_NRF52_PCA10040) || \
-      defined(CONFIG_BOARD_NRF52840_PCA10056)
+      defined(CONFIG_BOARD_NRF52840_PCA10056) || \
+      defined(CONFIG_BOARD_NRF52840_BLIP)
 
 #include <hal/nrf_saadc.h>
 #define ADC_DEVICE_NAME		DT_ADC_0_NAME