Use DT_INST_SPI_DEV_HAS_CS_GPIOS() in drivers to determine if we should
utilize CS_GPIO base SPI chipselect handling. This allows us to remove
Kconfig option for this feature.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Even though radio driver can report in its capabilities that it does
support CSMA CA, there's no way in the driver to select how the frame
should be transmitted (with CSMA or without). As layers above radio
driver (Thread, Zigbee) can expect that both TX modes are available, we
need to extend the API to allow either of these modes.
This commits extends the API `tx` function with an extra parameter,
`ieee802154_tx_mode`, which informs the driver how the packet should be
transmitted. Currently, the following modes are specified:
* direct (regular tx, no cca, just how it worked so far),
* CCA before transmission,
* CSMA CA before transmission,
* delayed TX,
* delayed TX with CCA
Assume that radios that reported CSMA CA capability transmit in CSMA CA
mode by default, all others will support direct mode.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
By changing the various *NET_DEVICE* macros. It is up to the device
drivers to either set a proper PM function or, if not supported or PM
disabled, to use device_pm_control_nop relevantly.
All existing macro calls are updated. Since no PM support was added so
far, device_pm_control_nop is used as the default everywhere.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The current design of the network-specific stack dumping APIs
is fundamentally unsafe. You cannot properly dump stack data
without information which is only available in the thread object.
In addition, this infrastructure is unnecessary. There is already
a core shell command which dumps stack information for all
active threads.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Update to use new API for GPIO pin configuration and operation. Fix
invalid arithmetic on void pointer. Mark all CC2520 GPIOs as required
in binding.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the int_literal_to_timeout Coccinelle script to convert literal
integer arguments for kernel API timeout parameters to the standard
timeout value representations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the named representation for no-wait to future-proof against a
change to the representation of timeout values.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
move misc/byteorder.h to sys/byteorder.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert DT_.*_GPIO_{CONTROLLER,PIN,FLAGS} ->
DT_.*_GPIOS_{CONTROLLER,PIN,FLAGS)
Used the following commands to make these conversions:
git grep -l DT_.*_GPIO_CONTROLLER | xargs sed -i 's/DT_\(.*\)_GPIO_CONTROLLER/DT_\1_GPIOS_CONTROLLER/g'
git grep -l DT_.*_GPIO_PIN | xargs sed -i 's/DT_\(.*\)_GPIO_PIN/DT_\1_GPIOS_PIN/g'
git grep -l DT_.*_GPIO_FLAGS | xargs sed -i 's/DT_\(.*\)_GPIO_FLAGS/DT_\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This macro is slated for complete removal, as it's not possible
on arches with an MPU stack guard to know the true buffer bounds
without also knowing the runtime state of its associated thread.
As removing this completely would be invasive to where we are
in the 1.14 release, demote to a private kernel Z_ API instead.
The current way that the macro is being used internally will
not cause any undue harm, we just don't want any external code
depending on it.
The final work to remove this (and overhaul stack specification in
general) will take place in 1.15 in the context of #14269Fixes: #14766
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
unify the API of CCM alogrithm's implemation for TinyCrypt,
mbedTLS and cc2520 crypto device to make users easy to use.
Fixes#8339.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Moving towards serialized fragmentation, adapting mac command creation
to avoid the need of ll_reserve etc...
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As for Ethernet, up to ieee802154 L2's send to actually sent the packet.
It's currently unoptimized as 6lo compression, 15.4 fragmentation and so
on will reallocate net_buf etc... but it's the first step towards
removing ll reserve space and more.
Applying changes to Openthread L2 as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that the in tree user of cc2520 uses device tree to configure SPI
and GPIO params, we can remove and convert the driver to utilize DT
only. This means removing the Kconfig options that come from DT and
rename CONFIG_ to DT_ for those options.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Allow to set debug also for RAW_CHANNEL and set general debug template
instead of networking one.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
L2 could take advantage of such hardware capability, when supported by
the device. This is also required for OpenThread.
Fixes#5714
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Driver is 'Busy' can be a warning message which can be enabled with
minimum debug level CONFIG_SYS_LOG_IEEE802154_DRIVER_LEVEL=2.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
- Renaming NET_L2_RAW_CHANNEL to NET_RAW_MODE
- Create a generic IEEE 802.15.4 raw mode for drivers
- Modify the IEEE 802.15.4 drivers so it passes the packet unmodified,
up to code using that mode to apply the necessary changes on the
received net_pkt according to their needs
- Modify wpanusb/wpan_serial relevantly
Fixes#5004
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Some "random" drivers are not drivers at all: they just implement the
function `sys_rand32_get()`. Move those to a random subsystem in
preparation for a reorganization.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
set_ieee_addr, set_short_addr and set_pan_id are now unused by L2, so
removing their exposure through the radio API.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Further support will need work per-driver basis, as soon as the L2 will
be able to make usage of such support.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The stack address was incorrectly specified when stack usage
was being debugged. This caused compiler to emit this warning
drivers/ieee802154/ieee802154_cc2520.c:1136:16: warning:
dereferencing type-punned pointer will break strict-aliasing
rules [-Wstrict-aliasing]
((struct cc2520_context *)(&__device_cc2520))->
^
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_stack_analyze function wants to look at the stack buffer,
but it is making assumptions on where this data is that are no
longer valid. Change to use the proper APIs for referencing this.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I4ec03eb2183d59ef86ea2c20d956e5d272656837
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- net_pkt becomes a stand-alone structure with network packet meta
information.
- network packet data is still managed through net_buf, mostly named
'frag'.
- net_pkt memory management is done through k_mem_slab
- function got introduced or relevantly renamed to target eithe net_pkt
or net_buf fragments.
- net_buf's sent_list ends up in net_pkt now, and thus helps to save
memory when TCP is enabled.
Change-Id: Ibd5c17df4f75891dec79db723a4c9fc704eb843d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There have been long lasting confusion between net_buf and net_nbuf.
While the first is actually a buffer, the second one is not. It's a
network buffer descriptor. More precisely it provides meta data about a
network packet, and holds the chain of buffer fragments made of net_buf.
Thus renaming net_nbuf to net_pkt and all names around it as well
(function, Kconfig option, ..).
Though net_pkt if the new name, it still inherit its logic from net_buf.
'
This patch is the first of a serie that will separate completely net_pkt
from net_buf.
Change-Id: Iecb32d2a0d8f4647692e5328e54b5c35454194cd
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will provide the feature through Crypto API.
Change-Id: If6953a54b393544b019755ae73571effe0724e69
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Allow user to set the four last bytes of a MAC address.
By default the bytes are selected randomly but for testing
purposes we need a way to specify the address in advance.
Change-Id: Ic9820a8026b327d1ee5025ab77fdc77f5778de67
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
