Remove `IEEE802154_SELECTIVE_TXPOWER` option.
Cache the tx power value in nRF5 driver and make use of it on each
operation.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
Add new `IEEE802154_CSL_DEBUG` Kconfig option that, when enabled,
prevents the radio to sleep after a delayed reception is finished.
This allows to debug CSL timing issues due to accuracy drifts in
communications between receiver and transmitter.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
The IEEE802154_2015 option is misleading, as it does not introduce full
802.15.4-2015 standard compliance but only random bits, plus it's
defined at the radio driver level, which brings yet another confusion.
Because of that, the option will be deprecated, and respective parts of
code that made use of it converted to use more specific configurations:
* nRF driver will now use CONFIG_NRF_802154_ENCRYPTION to specify
whether to compile in TX security
* net_pkt will only add extra 802.15.4 control block fields if
OpenThread is used, as they were solely used by this L2
* OpenThread radio layer will now use the OpenThread version to
determine whether to compile in TX security.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Over time, some non-standard concepts and extensions were introduced
into the stack (in KConfig, in drivers, in the internal API and into the
implementation) which makes introduction of additional standard-
compliant extensions like TSCH (and others) unnecessarily difficult.
To introduce extensions like TSCH it is required for the IEEE 802.15.4
stack to become more structurally aligned with the standard again which
will be the focus of some of the upcoming preparatory changes.
One way to check and prove standard compliance is to reference the
standard from within the source code. This change therefore introduces
inline references to the IEEE 802.15.4-2020 standard wherever possible.
Deviations from the standard are documented with TODO or deprecation
labels to be addressed in future changes.
In the future, new code introduced to the IEEE 802.15.4 stack should
be documented and reviewed for standard-compliance to avoid further
divergence. Most importantly:
* MAC/PHY configuration (via net mgmt, radio API, devicetree or
KConfig) should always be directly linked to well-defined MAC/PHY
PIB attributes if visible to the MAC API or the end user.
* Net management/shell/radio API commands should have a documented
reference to the corresponding MLME action from the standard.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Unify the drivers/*/Kconfig menuconfig title strings to the format
"<class> [(acronym)] [bus] drivers".
Including both the full name of the driver class and an acronym makes
menuconfig more user friendly as some of the acronyms are less well-known
than others. It also improves Kconfig search, both via menuconfig and via
the generated Kconfig documentation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Activating both, the IEEE 802.15.4 raw mode /and/ the L2 mode is not
possible and in fact leads to a build error.
It should therefore not be possible to activate both options at the same
time. This is achieved by only offering the (rather exotic) raw mode
once the L2-support for the IEEE 802.15.4 has been switched off.
Fixes: #48715
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
Previous to this change, each individual driver option depended on
NETWORKING. Instead, move dependency one level up.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the UART UPIPE IEEE 802.15.4 driver. This
allows to remove usage of IEEE802154_UPIPE_DRV_NAME in preparation for
the removal of NET_CONFIG_IEEE802154_DEV_NAME.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This commit extends the `struct net_pkt` structure with
`ieee802154_txpwr` field that contains signed value of the desired
transmission power of a IEEE 802.15.4 frame in dBm.
Signed-off-by: Jedrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
Align clock accuracy used in CSL calculations to the value in platform.
This is recomended setting for devices working in wide range
temperature. Nevertheless it can be profiled in end product to decrease
CSL window duration and finally the power consumption.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Introduce a common config for all 802.15.4 based L2 implementations.
This way, any custom 15.4 L2 implementation will be able to
automatically enable use 15.4 driver, w/o a need to modify the actual
Kconfig.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This commit implements the OpenThread APIs to pass MAC keys and
frame counter to the radio layer in order to process the
transmission security. This is needed for the correct functioning
of a CSL transmitter.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
Support for defining vendor specific OUI (Organizationally
Unique Identifier) was added.
Signed-off-by: Kamil Kasperczyk <kamil.kasperczyk@nordicsemi.no>
Some radio drivers need configuration before start-up. Up to now only
the RF2XX drivers allowed this, but other radio drivers need this as
well. In particular for setting EUI64 addresses.
Signed-off-by: Markus Becker <markus.becker@tridonic.com>
Add initial support for Decawave DW1000
IEEE 802.15.4-2011 UWB transceiver.
Driver has basic functionality. Additional functions such
as reading out timestamps and delayed TX were implemented
for test purposes, but also require support in the 802154
subsystem.
Register, sub-register, and defaults defines in the file
ieee802154_dw1000_regs.h are taken from the Decawave's
DW1000 driver for the Mynewt OS.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add initial Atmel at86rf2xx transceiver driver. This driver uses device
tree to configure the physical interface. The driver had capability to
use multiple transceiver and systems with multiple bands can be used.
With this, 2.4GHz ISM and Sub-Giga can be used simultaneous.
Below a valid DT example. This samples assume same SPI port with two
transceivers.
&spi0 {
status = "okay";
label = "SPI_RF2XX";
cs-gpios = <&porta 31 0 &porta 30 0>;
rf2xx@0 {
compatible = "atmel,rf2xx";
reg = <0x0>;
label = "RF2XX_0";
spi-max-frequency = <7800000>;
irq-gpios = <&portb 2 0>;
reset-gpios = <&porta 3 0>;
slptr-gpios = <&portb 3 0>;
status = "okay";
};
rf2xx@1 {
compatible = "atmel,rf2xx";
reg = <0x1>;
label = "RF2XX_1";
spi-max-frequency = <7800000>;
irq-gpios = <&portb 4 0>;
reset-gpios = <&porta 4 0>;
slptr-gpios = <&portb 4 0>;
status = "okay";
};
};
At the moment driver assume two transceiver are enouth for majority of
appications. Sub-Giga band will be enabled in future.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The upipe specific configuration options are selectable unconditionally.
This commit makes them depend on the upipe driver being enabled.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Allow to set debug also for RAW_CHANNEL and set general debug template
instead of networking one.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Log configuration was included only in case NET_L2_IEEE802154 was
enabled. In case of open thread this is not the case.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Adding spaces around "=" when definining Kconfig template so
that is more consistent with overall style of these template
variables.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This makes it easier to distinguish them from "true" undefined symbols.
Internally, all int/hex literals are treated as undefined symbols, which
always get their name as their value. The C tools work the same way.
The plan is to turn references to undefined Kconfig symbols into an
error later.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
CC1200 is a sub-ghz chip supporting 6 ISM & SRD bands: 169, 433, 470,
868, 915 and 920 MHz, with features dedicated to IEEE 802.15.4(g).
Current driver enables CC1200 against actual IEEE 802.15.4 Soft-MAC. 'g'
version support in the Soft-MAC will follow later.
The chip itself is closer to a bare metal radio modem than to a usual
15.4 chip: up to the user to provide the right RF settings for the
carrier band. Such settings can be generaten through TI's SmartRF tool.
Hopefully, for channel selection, this driver will be clever enough to
compute the proper register change without any special input from the
user. This will work for all the bands supported by the chip.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
A very old reference to former net stack was still lurking around.
Removing it.
Taking the opportunity to clear up dependencies.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- Renaming NET_L2_RAW_CHANNEL to NET_RAW_MODE
- Create a generic IEEE 802.15.4 raw mode for drivers
- Modify the IEEE 802.15.4 drivers so it passes the packet unmodified,
up to code using that mode to apply the necessary changes on the
received net_pkt according to their needs
- Modify wpanusb/wpan_serial relevantly
Fixes#5004
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This commit adds a driver for nRF5 802.15.4 radio. This driver
is a wrapper for the driver provided by ext/hal/nordic/drivers.
Change-Id: I20ee4aff3d1b994c621ba8eaab208d15d85e4c01
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
This commit changes Kconfig prefix for ieee802154 drivers to
IEEE802154_*. This is done for consistency with config prefixes
used in other subsystems.
Change-Id: Ibbb4d96d2b748f4f13135bde85304ec34c5a90a6
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
This commit splits 802.15.4 drivers configuration into separate files.
Change-Id: Ie1bed862e8f4248240fef18bc211d0ee8ca1493c
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
Instead of TI_CC2520_CHANNEL option NET_L2_IEEE802154_ORFD_CHANNEL is
used.
Change-Id: I9b0c0ff6b2c42070d05c5cf3e4dc33c364be9a5c
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add driver and configuration for the MCR20A 802.15.4
transceiver.
Jira: ZEP-1429
Change-Id: I0b17b688220a47c2f0e5cde269064bbd0dec824a
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add common log level for all IEEE802154 drivers.
Change-Id: If92c96b14e630d4482aadf9cacb25662d6663399
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Fibers do not exist anymore in unified kernel.
Also, let's just use that option directly so removing the internal
define which is then useless.
Change-Id: I1179d84401934b339d3a9ccd12f6145a120bcb2f
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As the native IP stack is now the default, there is no need
for corresponding Kconfig option.
Change-Id: I08e4992f540f928a2b7378e8803e634e38725348
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit removes the legacy Contiki based uIP stack.
The new native IP stack must be used after this commit.
The commit also removes following things:
- legacy cc2520 driver
- legacy ethernet drivers
- legacy IP stack samples
and changes these things:
- disabled tests that only work for legacy IP stack
- select new IP stack by default
- enable random number generator by default as it is needed
by the new IP stack
Change-Id: I1229f9960a4c6654e9ccc6dac14a7efb9394e45d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Since the whole init level changes: all drivers and most of subsystems
are initialized at level POST_KERNEL. Unfortunately that broke legacy
tweaks on what to start first and after.
Let's raise cc2520 priority, still below net_init.
Jira: ZEP-1261
Change-Id: I0d91aa87a893584b3f5b39a193c823127961402f
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
