Rename the Kconfig symbol for all ITE SoC variants.
Rename the SOC_SERITES_ITE_IT8XXX2 to SOC_SERIES_IT8XXX2.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
As of now only the resume action is supported, and doesn't perform
any power action on the GNSS modem.
It allows to initialize the GNSS driver later than it would otherwise
be.
Also, the driver now runs a modem-specific chat script on resumption.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
Major development work is concluded for Twister tests.
We should release appropriate information.
Signed-off-by: Lukasz Mrugala <lukaszx.mrugala@intel.com>
Deprecate the advertiser options `BT_LE_ADV_OPT_USE_NAME` and
`BT_LE_ADV_OPT_FORCE_NAME_IN_AD`.
Reasons:
- It is out of place in the advertiser options, as it acts on
advertising data and not configuration
- The behavior is not clear. All of these are trick questions:
- where does the data for the name go?
- do I have to allocate memory for this?
- does it work the same in legacy vs extended advertising?
- The trade-off between UX improvement and extra complexity in the host
is debatable. Hundreds of lines in the stack to avoid making the user
type out less than ten.
Also deprecate the following macros that uses those options:
- `BT_LE_ADV_CONN_NAME`
- `BT_LE_ADV_CONN_NAME_AD`
- `BT_LE_ADV_NCONN_NAME`
- `BT_LE_EXT_ADV_CONN_NAME`
- `BT_LE_EXT_ADV_SCAN_NAME`
- `BT_LE_EXT_ADV_NCONN_NAME`
- `BT_LE_EXT_ADV_CODED_NCONN_NAME`
Update the migration guide and the release note for Zephyr 3.7 to
describe those changes.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
Deprecate ETH_MCUX, by:
- Marking it as DEPRECATED in Kconfig, obviously.
- Unmarking the new driver as experimental.
- Putting the new and old drivers in the same folder.
- Reworking the menu appearance of the driver selection.
Note that technically now it is possible to choose the wrong
driver than what is enabled in DT, this is intentional, but
the correct one will obviously be enabled by default.
- Convert all sample overlays to the new Kconfigs. This was
part of the motivation for the shared overlays, as it was
causing twister/CI logs to look ugly and misleading due
to Kconfig warnings.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Mention the new can_get_bitrate_min() and can_get_bitrate_max() CAN
controller API functions along with the deprecating of the existing
can_get_min_bitrate() and can_get_max_bitrate().
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Remove IPSP support from the tree.
It has no maintainers, and is regularly broken. The fact that it's
nontrivial to set-up in linux makes it hard to fix reported issues.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
The SparkFun Pro Micro header pins are numbered D1, D0, GND, ... from top
left whereas the SparkFun Pro Micro RP2040 and the Adafruit KB2040 boards
are using gpio 0, 1, GND, ... , so the pro_micro: connector gpio-map of
these boards should reflect that.
Graphical Datasheet for SparkFun Pro Micro RP2040:
https://cdn.sparkfun.com/assets/e/2/7/6/b/ProMicroRP2040_Graphical_Datasheet.pdf
Graphical Datasheet for SparkFun Pro Micro:
https://cdn.sparkfun.com/assets/f/d/8/0/d/ProMicro16MHzv2.pdf
Pinout of the Adafruit KB2040:
https://learn.adafruit.com/assets/106984
Please note that the KB2040 uses CircuitPython pin labels D0, D1 which does
not seemt correspond to the Arduino labels D0 and D1 used by the Pro Micro.
Signed-off-by: Daniel Irekvist <ulmanyar@gmail.com>
Deprecate CONFIG_NET_TCP_ACK_TIMEOUT as it is redundant with the
combination of CONFIG_NET_TCP_INIT_RETRANSMISSION_TIMEOUT and
CONFIG_NET_TCP_RETRY_COUNT. The total retransmission timeout (i. e.
waiting for ACK) should depend on the individual retransmission timeout
and retry count, having separate config is simply ambiguous and
confusing for users.
Moreover, the config was currently only used during TCP handshake, and
for that purpose we could use the very same timeout that is used for the
FIN timeout. Therefore, repurpose the fin_timeout_ms to be a generic,
maximum timeout at the TCP stack.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The Virtual LAN is changed to use the virtual network interfaces.
Add information what changes might be needed because of this.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add enum for `constant-charge-voltage-max-microvolt` property to
signalize improper values given with device tree at compile time.
Signed-off-by: Lukasz Madej <l.madej@grinn-global.com>
Maximum charging current is selected with an external resistor in
the MAX20335 charger. Therefore it is not possible to configure it
with software directly. There is only a capability to limit current
set with hardware but configuration of the limiter is not
straight-forward.
To reflect real functionality, drop usage of
`constant-charge-current-max-microamp` property as an required one and
use custom `chgin-to-sys-current-limit-microamp` instead.
Use enum in binding file to signalize improper values at compile time.
Drop support for `CHARGER_PROP_CONSTANT_CHARGE_CURRENT_UA` API property
since this cannot be handled.
The `max20335_get_constant_charge_current()` function become useless so
remove it.
Signed-off-by: Lukasz Madej <l.madej@grinn-global.com>
Rework the data scaling algorithm for the "deadzone" mode so that the
deadzone is subtracted from the input rather than from the output. This
makes the whole output range usable rather than making the output jump
from the center value to the minimum deadzone range.
This changes the calibration data structure as well so now all values
refer to the input data, which is more coherent.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Putting a space between and the PR number causes the rendered
text to not link to the issue.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
A Kconfig item is added and the buffer
is embedded into the modem_cmux struct.
The default value is increased from 16 to 64 bytes in
an effort to reduce the number of modem_pipe_receive() calls.
CONFIG_MODEM_CHAT_LOG_BUFFER is renamed
to CONFIG_MODEM_CHAT_LOG_BUFFER_SIZE for consistency.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
The virtual interface API "input" callback is removed and
its functionality is implemented in "recv" callback.
This change affected the IP tunneling implementation in the
network stack.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add documentation on relevant sections to list addition of Bluetooth LE
service NUS (Nordic UART Service), as well as the UART driver for UART
over Bluetooth LE and snippets to easily enable it.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
Add a note about the ``sample-point`` and ``sample-point-data`` CAN
devicetree properties now being optional.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add release notes related to the added support for minimum supported CAN
transceiver/controller bitrates.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Commit adds const qualifier to models metadata.
Specification claims: Composition Metadata Page 0
shall not change during a term of a node on the network.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Due to the source/header files are moved to subfolder "classic",
rename the kconfig option BT_BREDR to BT_CLASSIC to make the
folder name and kconfig option name consistent.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
The IPv4 netmask handling is changed and it might need
adjustments from user if using more than one IPv4 address
inside one specific network interface.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
ws2812-gpio's `in-gpios` property is not used as an input pin.
Renaming it to `gpios` to reflect the actual situation.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
There are two kconfigs that are security related and are x86
specific. Prefix them with X86 to put them under the x86
namespace.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The current board porting guide explains the new hardware model without
making any references to the previous one. Add a new section that
explains the rationale behind the transition as well as adding important
bits of information for users that need to convert their boards.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Update the documentation page to reflect the latest LTSv2
release and tentative end-of-life (EOL) date.
Note: the actual EOL date is still dependant on the
official LTSv3 release date and may be subject to change.
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
