Having a per-instance init function makes code cluttered and hard to
read. Just create a per-instance IRQ connect function (required to
resolve IRQ_CONNECT parameters at compile time).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Stop using NRFX_SPI(S|M)_INSTANCE helper so that peripheral address from
Devicetree is used. We should not rely on HAL for hardware description
but Devicetree.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Move the RX (MISO) delaying capability information to Devicetree. It is
done using 2 properties:
- rx-delay-supported: enabled on SPI nodes that support delaying RX.
This property can be used by the driver to determine if this
capability is supported or not on a given instance.
- rx-delay: the actual RX delay value
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Specify the overrun character in Devicetree. Since 0xFF is the most
common value, DT property contains such default.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Extend the macro with checks for DT properties related to pin
assignments that are defined but would be ignored, depending on
whether PINCTRL is enabled or not, what presumably indicates
a resulting configuration different from what the user expects.
Add also a possibility to indicate that the pinctrl-1 property
should not be checked because the caller does not support the
sleep state.
Rename the macro so that its name better reflects its function.
Update accordingly all drivers that use it.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the SPI drivers that handle
the nRF SPI, SPIM, and SPIS peripherals. Update code of the drivers
and related devicetree bindings.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
- clean up registration of the drivers with the logging subsystem
- use consistent naming of local variables accessing configuration
and runtime data of driver instances, for easier code maintenance
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Only run the `uninit` function if the SPI instance has previously been
configured. This stops an assertion in the HAL drivers from triggering
due to running `uninit` without a previous `init`.
Fixes#42299.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Replace all get_dev_data()/get_dev_config() accessor utilities with
dev->data and dev->config.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In order to align with macros used to obtain a device reference (e.g.
DEVICE_DT_GET), align the PM macros to use "GET" instead of "REF". This
change should have low impact since no official release has gone out yet
with the "REF" macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device PM subsystem _depends_ on device, not vice-versa. Devices
only hold a reference to struct pm_device now, and initialize this
reference with the value provided in Z_DEVICE_DEFINE. This requirement
can be solved with a forward struct declaration, meaning there is no
need to include device PM headers.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Port some drivers to the recently introduced macros to showcase its
usage and be able to do some initial testing (nRF52840).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This is a follow-up to commits 99daca9bba
and ae03c0a6bf.
nRF SPI driver shims cannot use devicetree instance indexes, they need
to use the DT_NODELABEL macro and SoC peripheral instance indexes.
Correct the macros used in initialization of CS GPIOs in those shims.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
In case when we have multiple devices connected to the
one SPI interface the initial state of CS gpios after
MCU reset is floating and it might be low that prevents us from
communicating between particular devices. Fix that by
initializing all provided cs gpios and setting them as inactive.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
The PM callback is no longer referenced as "pm_control" but
"pm_action_cb", so reflect this new naming on the callbacks.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Apply the same changes as the previous commit made in the spi_nrfx_spim
shim, to keep these two shims aligned.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Instead of passing target states, use actions for device PM control.
Actions represent better the meaning of the callback argument.
Furthermore, they are more future proof as they can be suitable for
other PM actions that have no direct mapping to a state. If we compare
with Linux, we could have a multi-stage suspend/resume. Such scenario
would not have a good mapping when using target states.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
According to the documentation the OFF state has to be used when the
devices is fully turned off, ie, power removed. Most drivers were using
a sort of fall-through for all non-active states, leading to behaviors
not following the specifications.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The verb tense for the suspended state was not consistent with other
states. The likely reason: state was being used as a command/action.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The difference between low power and suspend states is a thin blur line
that is is not clear and most drivers have used indistinctly. This patch
converges to the usage of the suspend state for low power, since
contrary to the low power state, it is used by both system and runtime
device PM. The low power state is still kept, but its future is unclear
and needs some discussion.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device PM control function will only be called if the requested
state is different from the current one. A significant amount of drivers
were checking for state changes, now unnecessary. This patch removes all
this redundant logic.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Since the state is no longer modified by the device PM callback, just
use the state value.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The callback is now invoked to set the device PM state in all cases, so
the usage of ctrl_command is redundant.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device PM subsystem already holds the device state, so there is no
need to keep duplicates inside the device. The pm_device_state_get has
been refactored to just return the device state. Note that this is still
not safe, but the same applied to the previous implementation. This
problem will be addressed later.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The callback is not used anymore, so just delete it from the pm_control
callback signature.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
the device PM callback is not used anymore by the device PM subsystem,
so remove it from all drivers/tests using it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Move all PM_DEVICE_STATE_* definitions to an enum. The
PM_DEVICE_STATE_SET and PM_DEVICE_STATE_GET definitions have been kept
out of the enum since they do not represent any state. However, their
name has not been changed since they will be removed soon.
All drivers and tests have been adjusted accordingly.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The context parameter used across device power management is
actually the power state. Just use it and avoid a lot of
unnecessary casts.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
- Remove SYS_ prefix
- shorten POWER_MANAGEMENT to just PM
- DEVICE_POWER_MANAGEMENT -> PM_DEVICE
and use PM_ as the prefix for all PM related Kconfigs
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use the devicetree node as the source of object name and other
information used when defining the device structure.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Keep locking for SPI_LOCK_ON from the first call of transceive until
spi_release release the lock. Use owner parameter to in the spi_context
to store the owner of the lock.
The locking is in line with the SPI_HOLD_ON_CS
Signed-off-by: Stefan Bigler <stefan@bigler.io>
This removes a semaphore unlock in init_spi function
which causes risks of competitive access
Signed-off-by: Clotilde Sattler <clotilde.sattler@stimio.fr>
Function spi_context_longest_current_buf() has been introduced in
commit ddef35c1da for the purpose of
getting the longest possible (potentially partial) SPI transfer
for which all currently active directions have a continuous buffer.
Such transfer can be done with taking advantage of a DMA that cannot
use scattered buffers (and this is the case for nRF SPI drivers with
which this function has been introduced).
Unfortunately, because of its inadequate name, later on this function
has been incorrectly used in other SPI drivers for getting the longer
of TX/RX buffers. And commit afc480f12b
recently "fixed" the implementation of this function, assumably to
adjust it to those incorrect uses, but this way it has also broken
the nRF SPI drivers.
Instead of restoring the original implementation of the function in
question, this commit adds a new one with functionality equivalent
to that original but with a hopefully less misleading name, and this
function is used in the nRF SPI drivers.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
These are all the case that coccinelle cannot find as they are inside
macro declarations.
Fixed via:
git grep -rlz -E "\(struct device \*" |
xargs -0 sed -i 's/(struct device/(const struct device/g'
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Some needed to wrap the device pointer into device's data, where others
needed only device's data to be passed to HAL callback function.
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
