This contribution addresses the support for various types of modems in
gsm driver. As some 4G modems have failed to return correct output
from AT+CREG?, so AT+CEREG? is the right AT command in such situation.
This commit provides the possibility for user to select one type of
AT command. This PR fixes zephyrproject-rtos#63917
Signed-off-by: Tahir Akram <mtahirbutt@hotmail.com>
The driver should check for cellular registration before
attempting to attach to packet service, otherwise it will just
fails.
This patch waits for registration for 300 seconds, configurable
by CONFIG_MODEM_GSM_REGISTER_TIMEOUT, if it isn't registered by
then, it would toggle the airplane mode using AT+CFUN & wait
again, until it is registered, or `gsm_ppp_stop` is invoked.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add a name for the choice of gsm modem so that it can be
default to a certain type in board's Kconfig.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Waits until the network interface goes down before switching the
GSM_MUX. It uses the NET_MGMT_EVENT to signal a semaphore to
contiue when closed. This allows for the LCP state machine to
properly terminate. When skipping this wait, the second time
connecting, the connection might fail.
Tested on a real modem.
Fixes GSM PPP behavior in combination with: #41802
Signed-off-by: Sjors Hettinga <s.a.hettinga@gmail.com>
The driver performs AT commands configurations using the
system workqueue, this can delay the workqueue by up to 6
seconds to wait for the modem replies, which isn't ideal.
This PR creates a dedicated workqueue for the gsm, and
provides a helper function to reschedule work items to the
gsm workqueue.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Add support for Quectel modem in gsm_ppp modem driver.
The CMUX cmd is based on MUX application notes v1.0(2020-09-22)
for BG95, BG77 and BG600L. Tested and working on EC21e.
As the gsm_ppp doesn't do power control, it is required to power
on the modem manually in the application.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
This PR addresses radio signal stength measurement during
and before PPP session. The PR provides provides facility
of readout for both +CSQ and +CESQ versions depending
upon the modems. This PR follows the idea of rssi readout
of PR#35496. Additionally, reliable Cell info update
is also ensured.
Signed-off-by: Tahir Akram <mtahirbutt@hotmail.com>
In a previous commit, a check was added to ensure modem was properly
attached to packet service before initializing PPP. Failure to perform
this check can lead to the dreaded 'NO CARRIER' issue.
While this is a nice idea, the implementation was lacking because when
the check failed, the entire modem initialization procedure was
restarted from square one. For modems/bearers that were slow to attach,
this is potentially disastrous. The proper solution is to loop only the
'AT+CGATT?' part until it succeeds, or fails N times.
This commit implements this looping behavior (using the work queue).
Signed-off-by: Benjamin Lindqvist <benjamin.lindqvist@endian.se>
Autostarting PPP is far from controversial. There are many, many reasons
someone could have for wanting to control exactly when PPP starts. Power
management, NET_EVENT race condition avoidance and any application not
requiring constant and instant use of networking just to name a few.
This commit introduces a Kconfig setting, GSM_PPP_AUTOSTART, which
controls whether gsm_ppp should connect and initialize PPP at boot. It
is set to "y" as default to minimize surprises for legacy code.
Signed-off-by: Benjamin Lindqvist <benjamin.lindqvist@endian.se>
Some modems, under some conditions, have a tendency to get stuck without
a connection due to cached state. We have observed this on some Simcom
LTE modems after large cellular outages. The modems are unable to escape
their cached state for some reason unless they're factory reset (or a
cache clearence is forced in some other way).
This commit allows for the modem to be factory reset at each boot. This
minimizes dependencies on external state by ensuring each power-up is as
similar as possible.
Signed-off-by: Benjamin Lindqvist <benjamin.lindqvist@endian.se>
Instead of using physical UART to connection to the modem, use
the GSM 07.10 muxing protocol and UART mux driver to create
virtual channels to the modem. This will allow simultaneous
PPP, AT and other type connections to the modem.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add Kconfig option that allows user to set MCC (Mobile Country
Code). If user does not set it, then automatic operator
registration is used.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Create a driver for GSM modems that use a standard AT command set
and enable Zephyr's own PPP stack for IP traffic.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
