For demonstration purposes add a way to capture some arbitrary
data and send it in cooked mode for analysis.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If there are multiple tunnels, then use the tunnel device name
to select the correct one. Note that this tunnel is only used
for network packet capture in this sample application.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
User is able to enable packet capture for low level HDLC data
frames received from and sent to network. This data can sent to
remote system for analysis. The captured data is encapsulated
into Linux cooked mode SLL packets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If user created the capture device using the API and not via
the shell, then the device name was not set. Use the default
capture device in this case.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The event NET_EVENT_CAPTURE_STARTED is generated when the
capture is enabled, and NET_EVENT_CAPTURE_STOPPED when capture
is disabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
As user might not know the capture device name, allow
net_capture_is_enabled() to be called with a NULL device name.
Currently it then uses the hardcoded device name, but we could
change that in the future so that the function could figure out
the correct name itself.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The net_capture_pkt() does not return information what happened
to the net_pkt because the packet was always cloned. With cooked
capture we can avoid the cloning in which case we need to know
the capture status in order to unref the packet if needed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add support for capturing arbitrary data via the cooked mode (sll)
capture API. The actual packet capture is done using net_capture_data()
function, the packet capture infrastructure does not need any changes.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add ETH_P_CAN, ETH_P_CANFD and ETH_P_HDLC protocol types so that they
can be used in following commits.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Allow user to create a kitchen sink pseudo a.k.a any network
interface that one is only able to write to. This might seem
unnecessary, but it is possible to attach virtual network
interfaces on top of this pseudo interface. These virtual
interfaces could then process the data for example for
packet capture purposes.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
For debugging purposes it would be nice to see the verdict
printed as a string instead of number.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add a recv callback to dummy API. After this it is possible to
receive data by a dummy network interface. This is only useful
if one attaches a virtual interface on top of the dummy one.
One such example is the cooked mode capture interface.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The CONFIG_MAX_THREAD_BYTES=3 needs to be set for multiple
boards like mr_canhubk3 and xiao_ble when running in usermode.
Too many thread objects (18)
Increase CONFIG_MAX_THREAD_BYTES to 3
Fixes#70955
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The native_posix compilations fail with various socket
errors like this:
samples/net/sockets/echo_server/src/udp.c:45:26: error: implicit \
declaration of function ‘socket’ [-Werror=implicit-function-declaration]
45 | data->udp.sock = socket(bind_addr->sa_family, SOCK_DGRAM,
| IPPROTO_UDP);
Disable the native_posix board from networking samples so that CI can pass.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Improve Twister command line arguments for memory footprint:
* group and order footprint arguments meaningfully,
* clearer help descriptions,
* resolve logical inconsistences for combinations of arguments,
in particular:
`--last-metrics` now forces `--enable-size-report`,
`--show-footprint` now controls only detailed log output of
footprint deltas in comparison modes.
* align twister tests accordingly.
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
Improve code consistency and fix CONFIG_POSIX_API=n compatibility with use
of ZSOCK_* and DNS_* macros.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Refactor the skip collaborator logic to add log messages when a
collaborator is skipped because they self removed of not part of the
org.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The "frdm_k64f" is referred as frdm_k64f and ``frdm_k64f`` in
places, update them to ":ref:`Freedom-K64F <frdm_k64f>`" or
``frdm_k64f``.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Change 'Hawkbit' and 'hawkbit' to 'hawkBit' wherever
makes sense, and a bit of touch ups here and there.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
The initial version of an input driver for Cirque Pinnacle ASIC supports:
* Setting sensitivity
* Choosing between relative and absolute modes
* Relative mode
* Primary tap
* Swapping X and Y
* Absolute mode
* Setting number of idle packets
* Clipping coordinates outside of active range
* Scaling coordinates
* Inverting X and Y coordinates
Signed-off-by: Ilia Kharin <akscram@gmail.com>
Add harness as twister by default looks into ztest results and
in bluetooth configuration they won't be find.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
To prevent postponing data flush until filling fifo. Now the flush will
occur at the scheduled time, regardless of subsequent poll_out reqs.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
s/System Power Management/System Managed Device Power Management/g
System Power Management is confusing and does not tell
anything about device. Change it for something more explicit.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add support for supplying a broadcast code to the
broadcast audio sample, which will, if non-empty, encrypt
the broadcast.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
A few lines above this change explicitly enable the UART FIFO. Then this
line, goes and disables it. This seems to be from a workaround where the
parity and stop bits are not coming in correctly in the config. Fixing
that will be another patch. But, the FIFO should always be enabled. This
is visible when trying to use bit rates that are reasonably fast. Even in
IRQ mode, with a sufficient bit rate, bytes are readily dropped.
Tested on a Sparkfun Promicro rp2040 board.
Signed-off-by: David Brown <david.brown@linaro.org>
This commit fixes 'test_verify_send_report()' function as it was
not properly waiting for a MLDv2 report after sending a query. The
asserted value was set for the previous report sent after joining a
group.
Signed-off-by: Konrad Derda <konrad.derda@nordicsemi.no>
This commit fixes an issue where due to inverted logic (static function
returned 0 on success but the caller expected true/false) the MLDv2
reports were silently dropped.
Signed-off-by: Konrad Derda <konrad.derda@nordicsemi.no>
@Desvauxm-st is now retired and @ABOSTM is not working anymore on Zephyr
since some time now. Remove them and add @ajarmouni-st, which has been
contributing for some time now.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Automatically select CONFIG_GPIO when the GPIO-controlled CAN transceiver
driver is enabled. Update board configurations to benefit from this.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Added a check for checking duplication when adding a source in the
broadcast assistant, as per requirement in BAP 6.5.4. It is not
permitted to add a source such that a combination of broadcast_id,
adv_sid and address type would result in same triple of values.
Added a recv_state struct to cache these values when read, and moved
past_avail and srd_ids into this as well.
Signed-off-by: Fredrik Danebjer <frdn@demant.com>
Add pa variant definition to board.yml
Add bl654_dvk_nrf52840_pa files dts, yaml, defconfig
Update doc with information on variant and regulatory information
Signed-off-by: Jate Sujjavanich <jatedev@gmail.com>
Deprecate CONFIG_NET_TCP_ACK_TIMEOUT as it is redundant with the
combination of CONFIG_NET_TCP_INIT_RETRANSMISSION_TIMEOUT and
CONFIG_NET_TCP_RETRY_COUNT. The total retransmission timeout (i. e.
waiting for ACK) should depend on the individual retransmission timeout
and retry count, having separate config is simply ambiguous and
confusing for users.
Moreover, the config was currently only used during TCP handshake, and
for that purpose we could use the very same timeout that is used for the
FIN timeout. Therefore, repurpose the fin_timeout_ms to be a generic,
maximum timeout at the TCP stack.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add a harness to avoid twister waiting for results on the UART, which
won't happen unless there is a connection established to a remote
Bluetooth device.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
