This change ensures that shared memory doesn't hold any pre-reset
values after Soft reset is issued. When the Network Core boots up,
shared memory is always set to zero.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
Convert stm32 entropy driver to configuration based on device tree.
Select HAS_DTS_ENTROPY symbols and configure CONFIG_ENTROPY_NAME
in fixup files.
Since rng node is not enabled (or available) on all boards, it could
happen that symbol ENTROPY_STM32_RNG is not enabled and hence
ENTROPY_HAS_DRIVER not selected which ends up with a symbol
ENTROPY_NAME defined throufg Kconfig selection. Thus, in fixup file,
CONFIG_ENTROPY_NAME is defined only if not already defined.
Additionally, update boards that used to configure entropy by default.
On these boards, enable rng device in device tree and remove Kconfig
related configuration (which should not be part of default
configuration).
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Instead of using Kconfig options for setting the device name and IRQ
priority for the entropy_nrf5 driver, get these settings from the rng
node defined in DTS for a given SoC.
Provide also fixups for CONFIG_ENTROPY_NAME, until applications using
entropy drivers are converted to use DTS as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Correct the documentation page title for the
nRF9160 DK, to match the official Dev-Kit name.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add a deprecation warning for nrf5340 PDK when the old name,
nrf5340_dk_nrf5340, is used instead of the new board name.
For nRF5340 SoC: do this for both secure and non-secure board
targets, and for both Application and Network MCU.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
We rename the nRF53 Dev Kit board target (nrf5340_dk_nrf5340)
to nrf5340pdk_nrf5340. We update all associated references
in the supportive documentation and all nRF5340-related
cofigurations and overlay files in the samples and tests
in the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The board name for the Thingy:52, so far known as nrf52_pca20020, is
renamed to thingy52_nrf52832. Its documentation and all references to
its name in the tree are updated accordingly. Overlay and configuration
files specific to this board are also renamed, to match the new board
name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF52840 Dongle, so far known as
nrf52840_pca10059, is renamed to nrf52840dongle_nrf52840. Its
documentation and all references to its name in the tree are updated
accordingly. Overlay and configuration files specific to this board are
also renamed, to match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF52833 DK, so far known as nrf52833_pca10100,
is renamed to nrf52833dk_nrf52833. Its documentation and all
references to its name in the tree are updated accordingly.
Overlay and configuration files specific to this board are also
renamed, to match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board target for emulation of nRF52810 on nRF5DK, so far
known as nrf52810_pca10040, is renamed to nrf52dk_nrf52810.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF52 DK, so far known as nrf52_pca10040, is
renamed to nrf52dk_nrf52832. Its documentation and all references
to its name in the tree are updated accordingly. Overlay and
configuration files specific to this board are also renamed, to
match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF51 Dongle, so far known as nrf51_pca10031, is
renamed to nrf51dongle_nrf51422. Its documentation and all references
to its name in the tree are updated accordingly. Overlay and
configuration files specific to this board are also renamed, to match
the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add a reference to the PCA number to help users identify the board and
for consistency with the rest of the boards.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Also update counter_basic_api test to use DT_INST and remove the
udoo_neo_full_m4.conf as its not longer needed since the per instance
Kconfig sybmols don't exist anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Additionally remove udoo_neo_full_m4.conf from gpio_basic_api test since
the Kconfig symbols don't need to be set anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move board pinmux.c code to utilize
DT_NODELABEL instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all posix boards have a dts we can move the selection of
HAS_DTS to the arch level like it is for all the other architectures.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enables PWM support using the built-in red LED. Tested with:
- samples/basic/blink_led
- samples/basic/fade_led
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Kconfig options that enable I2C and SPI instances are no longer used
in nRF drivers. Remove all assignments done to these options in related
board definitions, samples, and tests.
For nrf52_pca20020, also no longer needed setting of default values
for GPIO_SX1509B* options is removed (now the gpio_sx1509b driver is
enabled by default when a corresponding devicetree node is enabled).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `UART_x_NRF_UART*` that select
the type of nrfx driver (for UART or UARTE peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding UART node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between UART and UARTE for a given instance.
Since all `UART_x_NRF_UART*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `I2C_x_NRF_TWI*` that select
the type of nrfx driver (for TWI or TWIM peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding I2C node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between TWI and TWIM for a given instance.
Since all `I2C_x_NRF_TWI*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `SPI_x_NRF_SPI*` that select the
type of nrfx driver (for SPI, SPIM, or SPIS peripheral) to be used
for a given instance. This prevents the options from being modified
in configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding SPI node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between SPI, SPIM, and SPIS for a given instance.
Since all `SPI_x_NRF_SPI*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert driver to utilize the new DT_INST macros completely and remove
associated Kconfig symbols that now come from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move to using DT_NODELABEL to get references to specific GPIO ports on
various boards that utilize the arm,cmsdk-gpio controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Make the label property required for "arm,cmsdk-gpio" compatible
nodes. Update binding to mark the 'label' property required and updated
associated .dts files to add a 'label' property if it didn't exist.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use device node declaration instead.
Clean up GPIO_STM32_PORT* Kconfig symbols.
On some boards some gpio ports where disabled using Kconfig symbols.
Disable them now via device tree nodes in boards dts files.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use "nRF9160 DK" throughout. Change the title to "Development Kit" and
introduce the abbreviation there.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
PWM and other flags were missing for PCA10059.
Aligned also RAM and Flash while comparing the files.
Signed-off-by: Markus Becker <markus.becker@tridonic.com>
