This update stm32h747i_disco board display config to use ltdc frame
buffer config feature.
For lvgl, by default ltdc frame buffer number set to 0.
Signed-off-by: HaiLong Yang <hailong.yang@brainco.cn>
Use a board with a mikroBUS as example in the shield documentation and
update the example application since the board_shell sample was removed in
commit 7c85f4b2f5.
Fixes: #67134
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Include zephyr/dt-bindings/adc/adc.h in the shield DTS overlays to simplify
using this shield in application overlays.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Update dts files to use ST vendor specific HCI SPI Bluetooth driver.
Remove unnecessary GPIO bias for output pins.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
This adds a hint that for stm32h747i_disco just some display shields are
supported.
Signed-off-by: Maximilian Huber <gh@maxhbr.de>
Co-authored-by: Benjamin Cabé <kartben@gmail.com>
Include zephyr/dt-bindings/adc/adc.h and zephyr/dt-bindings/gpio/gpio.h in
the shield DTS overlays to simplify using this shield in application
overlays.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Use the common io-channel-cells name "input" instead of "positive" and
"negative" to make this binding work with the various ADC DT macros.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove BT_SPI_BLUENRG Kconfig parameter as it is redundant according to
the new changes introduced by ST SPI protocol V1 and V2.
Remove "config BT_SPI_BLUENRG" from the boards that were using it.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
The existing npm1300_ek shield overlay has several example
voltage and gpio settings. For many use cases these are
invalid and need to be overridden, or removed with
delete-property.
These example configurations have been moved to a board
specific overlay.
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
Add support for low power mode on the G1120B0MIPI using the RT595. This
configuration is tested via a testcase in samples/drivers/display, which
should validate that the display can be driven by the RT595 when
CONFIG_PM and CONFIG_PM_DEVICE are set.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This chip uses an active low reset, so the correct behavior here is to
define the pin as ACTIVE_LOW, using GPIO_OUTPUT_ACTIVE to assert the
reset and set to 0 to deassert.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This chip uses an active low reset, so the correct behavior here is to
define the pin as ACTIVE_LOW, using GPIO_OUTPUT_ACTIVE to assert the
reset and set to 0 to deassert.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Modify SPI configuration to match the features introduced in PR #63437.
Set the property "controller-data-delay-us" to zero for boards
which are using BlueNRG-MS.
Fix Chip Select configuration for stm32l562e_dk board.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
Unify spelling of CAN Flexible Data-rate abbreviation to "CAN FD" instead
of "CAN-FD". The former aligns with the CAN in Automation (CiA)
recommendation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
M5Stack-Core2 comes with a base shield that is connected to the M5Stack
extention connector. It features a MPU6886 6-axis motion tracker
and a SPM1423 microphone.
Signed-off-by: Martin Kiepfer <m.kiepfer@teleschirm.org>
Add shield definition for the MikroElektronika ACCEL 13 Click.
The ACCEL 13 Click carries a IIS2DLPC ultra-low power triaxial
accelerometer sensor in a mikroBUS form factor.
Signed-off-by: Mark Olsson <mark@markolsson.se>
Make sure devicetree, kconfig, etc. code snippets all have proper
pygments language set.
Note: only existing code-block:: directives have been updated. Another
pass should be made to address implicit code-blocks (`::`)
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Update the descriptions for the various CAN devicetree timing properties
specified in Time Quanta (TQ) to make it clear that these, if present, are
only used for the initial timing parameters.
Deprecate the (Re-)Synchronization Jump Width (SJW) devicetree properties
for both arbitration and data phase timing as these are now only used in
combination with the other TQ-based CAN timing properties, which are all
deprecated.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
While recent browsers seem to transparently try to use https for
http://www.st.com/... URLs, they are effectively not working anymore, so use
https://www.st.com/... URLs instead.
curl http://www.st.com/en/evaluation-tools/nucleo-g070rb.html -m 5 -v
* Trying 104.89.117.48:80...
* Connected to www.st.com (104.89.117.48) port 80 (#0)
> GET /en/evaluation-tools/nucleo-g070rb.html HTTP/1.1
> Host: www.st.com
> User-Agent: curl/8.1.2
> Accept: */*
>
* Operation timed out after 5002 milliseconds with 0 bytes received
* Closing connection 0
curl: (28) Operation timed out after 5002 milliseconds with 0 bytes
received
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Update all Nucleo shield samples and references to them so that they
use the new zephyr:code-sample extension.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Add support for using SMARTDMA when using RM67162 display shield with
Zephyr, so that the DMA engine can be leveraged for improved performance
when using the MIPI DSI in command mode.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Use the new code-sample directive and roles to document the networking
samples so that they show up as "Related samples" when browsing the
various relevant networking APIs.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Determine sh1106 from the `compatibility` value instead of
the SSD1306_CONTROLLER_TYPE setting.
Change the settings in `boards/shields/ssd1306/sh1106_128x64.overlay`
to follow this change.
Remove the SSD1306_CONTROLLER_TYPE from its Kconfig.defconfig,
and set the `compatibility` to `sinowealth,sh1106`.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add shield definition for the TI TCAN4550EVM, an evaluation module for the
TI TCAN4x5x CAN controller series.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Change boards and shields and remove kscan nodes in favor of the
"zephyr,lvgl-pointer-input" compatible.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Change boards and shields which enable the LV_Z_POINTER_KSCAN symbol to use
the new "zephyr,lvgl-pointer-input" compatible instead.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Enable LZ_Z_FLUSH_THREAD for display shields and boards that are known
to benefit from this optimization.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add probe address setting to RT595-EVK, to work around board issue with
routing of INT GPIO that prevents GPIO from being set to output mode.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add gpio-keys codes for all boards. These are mostly INPUT_KEY_0 and so
on but I've used some more specific ones where it was obvious that
there's something else on the boards.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add rk055hdmipi4ma0 shield, which uses an HX8394 TFT LCD controller and
GT911 touch IC. This shield is enabled on the RT595 and RT1170 EVK,
which have 40 pin FFC interfaces capable of connecting to the display.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add g1120b0mipi watch display to shields. This shield is currently
supported with the RT595 and RT1170 EVK. The shield contains a 400x392
circular OLED watch display, with an integrated RM67162 display controller
Note that the touchscreen IC can be driven by the FT5336 driver, with the
following changes:
- the FT3267 reports touch data as inverted from the FT5336, so
LVGL must be made aware of this via CONFIG_LV_Z_POINTER_KSCAN_INVERT_Y
- the FT3267 reports the X and Y coordinates as swapped from the FT5336.
To resolve this, the RM67162 driver reports the display as rotated by
90 degrees.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Only set LV_Z_VDB_CUSTOM_SECTION for the RK055HDMIPI4M shield, as it
is only required when using displays that require a large framebuffer.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
GT911 IC uses the INT pin to select the correct I2C address during
reset. However, some boards may not route this pin (or may only support
receiving inputs on it). This results in the I2C address selected by the
GT911 IC being arbitrary based on the state of the (floating) INT pin.
To resolve this, introduce an `alt-addr` property for this device. When
set, the INT pin will not be pulled low. Instead, the I2C address will be
probed at runtime, starting with the devicetree address and falling back to
`alt-addr`.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
During testing I've found one bad path and looked if
there is more.
I've used this oneliner to find more:
```
rg :zephyr-app: | awk '{ print $3 }' | while read dir
do
test -d $dir || echo $dir
done | grep '^samples' | grep -v '<' | sort | uniq
```
Signed-off-by: Nerijus Bendžiūnas <nerijus.bendziunas@gmail.com>
Convert the GT911 driver to the input subsystem, fix the existing boards
to work in the default config.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add Arduino compatible LoRaWAN shield based on SX1276 tranceiver from
Semtech. Provide minimal documentation on how to use it.
Tested with `nucleo_l073rz` platform.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Add rk055hdmipi4m shield definition. This shield contains a 1080x720
display driven by an RM68200 IC, with a GT911 touch controller. The
display is supported by a 40 pin FFC connector present on NXP's RT1170
and RT595 EVKs.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Drop the GPIO and EEPROM priority override. The current settings have
been introduced as part of a major priority refactoring but I don't
think they are needed anymore, and they currently result in this error:
ERROR: /soc/spi@4002d000 POST_KERNEL 70 <
/soc/gpio@400ff100 POST_KERNEL 99
found with:
west build -p -b frdm_k64f samples/shields/lmp90100_evb/rtd \
-DCONFIG_CHECK_INIT_PRIORITIES=y
Dropping the two overrides should work fine, leaving the ADC override as
that seems like is still needed.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
MIPI-DSI initialization priority got delayed in fed377f622, but now
that's at the same priority as the OTM8009A for this board
configuration, and OTM8009A needs MIPI-DSI to be initialized. Being at
the same priority means that it may or may not work depending on the
linking order, this is exposed with:
$ west build -p -b stm32h747i_disco_m7 samples/subsys/display/lvgl \
-DSHIELD=st_b_lcd40_dsi1_mb1166 \
-DCONFIG_CHECK_INIT_PRIORITIES=y
...
WARNING: /soc/dsihost@50000000/otm8009a@0 POST_KERNEL 86 ==
/soc/dsihost@50000000 POST_KERNEL 86
Bumping the display priority up to make sure it still works.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Adding support for the adafruit can picowbell shield for the
raspberry pi picoi. Also added nodelable for spi0 called 'pico_spi'
as well as an GPIO nexus node 'pico_header'
Signed-off-by: Joseph Yates <joeyatessecond@gmail.com>
