Using ztest predicate feature, testcases are skipped, however, the skip
is only reported as part of the summary and not through normal
execution. Until now such tests were reported as blocked or had a null
status in the twister json output.
This changes will look into summary results and use them to confirm
parsed results and add any missing results that either were not reported
or not captured through the serial console.
The issue can be observed with the drivers.can.api test for example on
the frdm_k64f board.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
uicr_ranges dictionary entries did not contain the `_FAMILY` suffix, now
used by self.family variable, resulting in an always false check.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
As saving tests writes to file, rather than appending to it,
we should indicate that in the --save-tests help.
--load-tests help changed so its grammar is the same as --save-tests's.
Signed-off-by: Lukasz Mrugala <lukaszx.mrugala@intel.com>
When pytest harness test is run on harware, messages sent from target
right after application start-up are lost, because connection to COM
port is not established yet. It can cause unexpected
behavior of a test. Fix it by flashing and running application after
connecting to COM port when testing on hardware.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Import of pty module causes exception when pytest harness is used
for device testing on Windows. Fix it by importing pty module
on non-windows hosts only. Add logger message for case pty
is used by mistake on Windows.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Comparisons that have constants on both side of the operator
were getting flagged incorrectly. Adjust the check so that
pure constant comparisons are not flagged, reducing false
positives.
WARNING:CONSTANT_COMPARISON: \
Comparisons should place the constant on the right side of \
the test
+BUILD_ASSERT(CONFIG_MAX_PTHREAD_COUNT == \
CONFIG_MAX_PTHREAD_MUTEX_COUNT - 1);
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
Building the HEX file is optional (CONFIG_BUILD_OUTPUT_HEX), so
`bmp_flash` will fallback to elf_file if missing. Additionally, to
maintain section names the HEX is only used if it is signed.
Signed-off-by: John Whittington <git@jbrengineering.co.uk>
The cfg.elf_file is not signed, so `west flash` with a sysbuild will
not run the application if MCUboot image signature checking is on. Using
the cfg.hex_file for `bmp_flash` resolves since as the signed hex is
used when using sysbuild. Symbols are not required for flashing so the
switching from elf to hex is not an issue.
Signed-off-by: John Whittington <git@jbrengineering.co.uk>
clear_log is used to prevent a common pytest log error,
which makes logs unusable in testing.
Such a fix is useful for all tests,
so it should be autouse by default.
Signed-off-by: Lukasz Mrugala <lukaszx.mrugala@intel.com>
This constant is supposed to be defined as a long instead of an int,
presumably to support systems where int isn't large enough.
Signed-off-by: Keith Packard <keithp@keithp.com>
If people are using the zcbor script for code generation, it needs to be
at the latest version
Signed-off-by: Øyvind Rønningstad <oyvind.ronningstad@nordicsemi.no>
clear_log is used as a fixture by pytest. We need to be able to call
it from the code level. Example of use in the file
test_harwaremap.py line 157.
Signed-off-by: Paszkiet Kamil <kamilx.paszkiet@intel.com>
Update helper method used by pytest fixtures. Extended upload
method with 'slot' parameter. Added searching of uploaded images
that can be tested or confirmed.
Signed-off-by: Grzegorz Chwierut <grzegorz.chwierut@nordicsemi.no>
Currently it is tedious to know the level of an interrupt for
a node in C. One would have to go through a very complex and
error prone macros to check if there's a parent interrupt
controller & if the controller has an interrupt number and thus
not a pseudo interrupt controller like the one found in
`rv32m1`. The level of a node is required to encode the
Zephyr's multi-level interrupt number
Since it is easier to do it in the `gen_defines` script, let's
do the heavy lifting there so that we can introduce new DT
macros to get the interrupt level very easily later.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
When using direct isrs, a vector table is needed. However, if none is
present , i.e. `CONFIG_GEN_IRQ_VECTOR_TABLE=n`, this script failed. The
given error message was not helpful (`'NoneType' has no len()`).
This change makes it clearer, where to look for the problem.
Signed-off-by: Greter Raffael <rgreter@baumer.com>
When twister is run on Windows with --short-build-path option, mklink
fails to create link, because path to build dir contains forward
slashes, which are not handled correctly by mklink.
Fix it by using os.path.normpath in mklink call.
Added os.path.join mock in twister unit test to handle path join
consistently.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Currently, the noclearout pytest mark generates warnings because
it is not registered.
This commit adds its registration in the relevant conftest.
Signed-off-by: Lukasz Mrugala <lukaszx.mrugala@intel.com>
Automatically populate the snippet roots from Zephyr modules, instead of
only looking in `ZEPHYR_BASE`.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Rather than duplicating the same schema, define it only once and reuse
for both common section and tests section.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Extend the gen_defines.py write_interrupts(node) function to
generate macros to get the interrupt controller for an
interrupt specifier by idx and by name.
The information is already generated by edtlib.py and stored in
node.interrupts[].controller. This addition uses the node pointed
to by the controller member to generate the following example output
define DT_N_S_device1_IRQ_IDX_0_CONTROLLER \
DT_N_S_gpio_800
define DT_N_S_device1_IRQ_NAME_test4_CONTROLLER \
N_S_device1_IRQ_IDX_0_CONTROLLER
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
The "Submitter is same as Assignee" is comparing strings to <Area> and
always failing the condition, fix it by dropping the ".name".
Tested with ./scripts/set_assignees.py -v -y -P 67526 (now falls back to
the other maintainer as it should).
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Align with native_simulator's upstream main
880eea00abf0191f3d986559876359a5422c9618
Which includes:
* 880eea0 HW scheduler: Minor optimization
* 37c0d86 Minor: Comment fix: Remove out of date reference
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add dt_node_ph_array_prop_int/hex function to query value of cells
from a phandle-array property of a node at a given index of the array.
Based on dt_node_array_prop_int/hex.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
When using the code and data relocation feature, every relocated symbol
would be marked with `KEEP()` in the generated linker script. Therefore,
if any input files contained unused code, then it wouldn't be discarded
by the linker, even when invoked with `--gc-sections`.
This can cause unexpected bloat, or other link-time issues stemming from
some symbols being discarded and others not.
On the other hand, this behavior has been present since the feature's
introduction, so it should remain default for the users who rely on it.
This patch introduces support for `zephyr_code_relocate(... NOKEEP)`.
This will suppress the generation of `KEEP()` statements for all symbols
in a particular library or set of files.
Much like `NOCOPY`, the `NOKEEP` flag is passed to `gen_relocate_app.py`
in string form. The script is now equipped to handle multiple such flags
when passed from CMake as a semicolon-separated list, like so:
"SRAM2:NOCOPY;NOKEEP:/path/to/file1.c;/path/to/file2.c"
Documentation and tests are updated here as well.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
We are not setting the review rule value correctly and default to 'no'
for all prs, even if they were correctly reviewed by assignees.
Minor other cleanups.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
If a collaborator removes themselves from the reviewer list, do not
attempt to re-add them on changes to the PR.
Fixes#67214
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Bounds check the array access in case the input data changes so that the
number of entries in the 'children' array is not the same. The tool output
with this change isn't terribly useful, but at least it doesn't crash.
Signed-off-by: Keith Packard <keithp@keithp.com>
A simple workflow that runs when a PR is merged and updates the
elasticsearch index with merged PR info.
The dashboard for displaying the information can be found here:
https://kibana.zephyrproject.io/
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Harness is freeform right now in the yaml file and if the harness is not
implemented in class, things fail. While we cleanup and enforce
implementations, this should serve as a quick fix dealing with such
unimplemented harnesses.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Current blacbox tests leave two folders,
OUT_DIR and TEST_DIR after they are finished.
Unit tests create two further folders,
mock_testsuite and demo_board_2.
This change deletes them appropriately.
Additionally, the created twister-out* folders in blackbox tests are
moved to a temp directory and removed after every test.
Signed-off-by: Lukasz Mrugala <lukaszx.mrugala@intel.com>
To make possible to build bsim tests by Twister, it is necessary to
copy executables to BabbleSim bin directory.
Signed-off-by: Piotr Golyzniak <metody159@gmail.com>
Add support for J-Link over IP and J-Link remote server.
If the "--dev-id" is a valid ip, the transport over ip is selected.
Otherwise usb is selected.
Signed-off-by: Michael Arnold <marnold@baumer.com>
The current zephyr.spdx does not contain the modules included in the build.
This commit split the zephyr-sources package into multiple packages, one
for each modules found by zephyr_module.py.
Signed-off-by: Thomas Gagneret <tgagneret@witekio.com>
Generated outputs can be difficult to read, preserving comments helps a
lot and they often provide good `git grep` search keywords.
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Zero-functional change.
Also move it to a separate line so it's more convenient to temporarily
comment it out.
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
