Simplify the driver header implementation, so that there are not
structs and unions different per each situtaion, and make just one
function for the enet module drivers to call on each other. Also,
capitalize existing enums.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
MDIO controller is part of GMAC and it requires GMAC ethernet driver to
initialize first because it will reset the whole GMAC hw block during
initialization. Both C22 and C45 APIs are supported.
Co-authored-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
Do not enable subsystem/driver shell modules by default and stop abusing
CONFIG_SHELL_MINIMAL, which is internal to the shell subsystem, to decide
when to enable a driver shell.
The list of shell modules has grown considerably through the
years. Enabling CONFIG_SHELL for doing e.g. an interactive debug session
leads to a large number of shell modules also being enabled unless
explicitly disabled, which again leads to non-negligible increases in
RAM/ROM usage.
This commit attempts to establish a policy of subsystem/driver shell
modules being disabled by default, requiring the user/application to
explicitly enable only those needed.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
At present, many of the NXP S32 shim drivers do not make use of
devicetree instance-based macros because the NXP S32 HAL relies on an
index-based approach, requiring knowledge of the peripheral instance
index during both compilation and runtime, and this index might not
align with the devicetree instance index.
The proposed solution in this patch eliminates this limitation by
determining the peripheral instance index during compilation
through macrobatics and defining the driver's ISR within the shim
driver itself.
Note that for some peripheral instances is needed to redefine the
HAL macros of the peripheral base address, since the naming is not
uniform for all instances.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Initialize the MDIO peripheral clock (normally done during GMAC
initialization) before trying any MDIO transfers, preventing startup
errors.
Signed-off-by: Nick Kraus <nick@nckraus.com>
MDIO is currently initialized in the ETH NXP S32 NETC
driver for Physical Station Interface (PSI), so do not
try to build the MDIO driver if the ETH driver is not built
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Add `mdio_read_c45()`/`mdio_write_c45()` APIs for Clause 45 access
and remove the `protocol` MDIO binding property so that MDIO bus
controller can support more than one protocol.
A new MDIO header is introduced with generic opcodes, MMD and
registers addresses, to be used by MDIO and PHY drivers.
Existing MDIO drivers that support both Clause 22 and Clause 45
access are migrated to the new APIs.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Rename argument `devad` to `regad` to indicate this is the register
address in a given PHY device and to not be confused with the
Clause 45 device address within a port.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
NOCACHE_MEMORY depends on ARCH_HAS_NOCACHE_MEMORY_SUPPORT, so
don't try to select the symbol if not supported.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add MDIO driver that works through GPIO pins. This driver is
useful when a microcontroller doesn't have MDIO bus or when multiple
separate MDIO buses are required. The driver provides access to
the MDIO bus through GPIO pins for any SoC that has GPIO pin control
available.
Signed-off-by: Aleksandr Senin <al@meshium.net>
This driver implements an MDIO device. Enable the MDIO driver to avoid a
build error for:
orphan section `._device.static.3_CONFIG_MDIO_INIT_PRIORITY_'
Also set the proper compatible in mdio_shell so that the ethernet tests
build correctly.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Make ethernet phys childs of the mdio device and move the mdio device up
a level on the tree. That makes the device hierarchy coherent with the
required initialization priority and allows keeping the sequence in
check with CHECK_INIT_PRIORITIES.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Refactor the ESP32 target SOCs together with
all related boards. Most braking changes includes:
- changing the CONFIG_SOC_ESP32* to refer to
the actual soc line (esp32,esp32s2,esp32s3,esp32c3)
- replacing CONFIG_SOC with the CONFIG_SOC_SERIES
- creating CONFIG_SOC_FAMILY_ESP32 to embrace all
the ESP32 across all used architectures
- introducing CONFIG_SOC_PART_NUMBER_* to
provide a SOC model config
- introducing the 'common' folder to hide all
commonly used configs and files.
- updating west.yml to reflect previous changes in hal
Signed-off-by: Marek Matej <marek.matej@espressif.com>
The prompt is referring to another existing driver(NXP S32),
now the correct name is displayed.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Adds MDIO driver. Works via exposed
ADIN2111 functions.
It is possible to access Clause 45 and 22 registers.
Due to MDIO API limitation Clause 45 access
is done using driver specific MDIO functions.
Provides API and functions for PHY driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Unify the drivers/*/Kconfig menuconfig title strings to the format
"<class> [(acronym)] [bus] drivers".
Including both the full name of the driver class and an acronym makes
menuconfig more user friendly as some of the acronyms are less well-known
than others. It also improves Kconfig search, both via menuconfig and via
the generated Kconfig documentation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Introduce NXP S32 NETC External MDIO controller driver. Driver supports
a single instance, as current support is based on NXP S32Z/E SoCs.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This update Atmel sam and sam0 ethernet gmac and mdio drivers to use
pinctrl driver and API. It updates all boards with new pinctrl groups
format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Just use dev->name. This change follow same principles applied when
DEV_CFG and DEV_DATA macros were removed.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Stop using redundant DEV_DATA/DEV_CFG macros and use dev->data and
dev->config instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Replace usages of DT_PARENT(DT_DRV_INST(idx)) with more idiomatic
DT_INST_PARENT(idx).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
