Replace use of Kconfig UART_X symbols by calls to DT API.
Clean driver from symbols definitions
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This selects CONFIG_BT_HCI_RAW_H4 which indicates to hci_raw to handle
H:4 header automatically.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This makes hci_raw to manage RX and TX buffers so its logic don't have
to be replicated on each an every driver/application, it also makes it
simpler to deal with extra headers for H:4 mode since that then can be
done at earlier at buffer allocation.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds USB_PID_BLE_HCI_H4_SAMPLE along with it driver which uses H4
over bulk endpoints.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Convert from using dts_fixup.h based macros to DT_INST macro. This lets
us remove the dependancy on dts_fixup.h for this driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added default configuration files for nrf5 boards so the sample
is building with expected features for these boards.
Would be greater to use OVERLAY_CONFIG instead of files addition,
but that doesn't work from CMakeLists.txt scope.
fixes#24442
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Now the ARC SecureShield related features are experimental. The ARC
normal application cannot run alone, need the secure service example to
initialize the context and boot.
Here move ARC normal related configurations out of board dir to
avoid the impact of CI test and the confusion to users.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Move to the new devicetree API and stop using DT_WDT_0_NAME fixup
macros. All existing in-tree SoCs with fixup names are still supported
here via compatible. The watchdog0 alias is also still supported.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
During the last refactoring of the sample, CONFIG_MCUMGR_CMD_FS_MGMT
was mistakenly set to n instead of y for the bluetooth transport.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@prevas.dk>
This sample now supports SMP UDP transport.
Two config overlays have been added for ipv4 and ipv6, respectively.
The sample documentation has been completely revamped to be less
bluetooth focused and more general.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@prevas.dk>
To prepare this sample supporting future SMP transports, the sample
code is now split into a main and bluetooth file. A common config
has been identified and application specific config is put into
overlay config files.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@prevas.dk>
This board contains an on-board Winbond W25Q16.
The chip is connected to spi1 using PB3-PB5 and PB0 as CS.
Signed-off-by: Bjarne Steinsbo <bjarne@gmail.com>
Remove usage of Kconfig symbols I2C_X and rely on overlay
to enable i2c instances in samples for stm32 boards
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch introduces two major changes to the directed advertising
feature of the bluetooth host.
Deprecating the bt_conn_create_slave_le, and removing
bt_conn_le_create_slave which has never been released. This behaviour
has now been moved by to providing the peer direct address into the
advertising parameters.
Introducing directed advertising support for nonconnectable
directed extended advertising, both scannable and non-scannable.
A bug was also fixed in the the directed-adv command in the shell
when the argument "low" was given. The advertiseng parameter pointer
declared with BT_LE_ADV_CONN_DIR_LOW_DUTY was declared in a scope that
was no longer valid when it was used to start the advertiser.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references where
needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
I personally don't find it very useful to have to maintain prj.conf
and prj_spi.conf for this sample. The information we need to make
this application "just work" with regards to the bus is available in
the devicetree, and Kconfig can now access it using
dt_compat_on_bus().
Do so, enabling I2C and SPI appropriately when a sensor of the right
type is on either of those buses.
If no sensors are enabled, the user gets the build-time error message
in main.c about no devices being found.
This approach is prone to the "stuck symbol" Kconfig problem covered
in our documentation, so a pristine build is necessary to change the
default settings from a previous build.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Use instance zero of the compatible to get the device instead of
fixing a label. Print the used label for help debugging, and the
results of finding the device (or not), with a hint about what might
have gone wrong in case of failure.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The nrf52840-DK doesn't have this sensor built-in, so it's likely
users will be getting this sensor from a breakout board. The ones that
Sparkfun and Adafruit sell pull up the LSB address pin, so the default
address is 0x77 on those boards.
Let's follow along with them instead of using 0x76, because those are
the boards that come up first in the results when you google "BME280
breakout board" from where I'm sitting.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This helps debug issues with the device. Samples should try to be
helpful to first-time users. Send printk() to logging so it doesn't
fight over the UART.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add bq274xx sample with reading and showing all
possible values from the sensor.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Signed-off-by: NavinSankar Velliangiri <navin@linumiz.com>
Replace CONFIG_ENTROPY_NAME with DT_CHOSEN_ZEPHYR_ENTROPY_LABEL. We now
set zephyr,entropy in the chosen node of the device tree to the entropy
device.
This allows us to remove CONFIG_ENTROPY_NAME from dts_fixup.h. Also
remove any other stale ENTROPY related defines in dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Those are used only in tests, so remove them from kernel Kconfig and set
them in the tests that use them directly.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The variables passed by sanitycheck and west were being ignored because
cmake knows nothing about them.
Fixes#24178
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The origin for sleeping for 3ms after coming out of deep sleep
was to wait for PLL to lock so that UART would not send
garbage characters due to incorrect clock. In the deep sleep
code, it spins to wait for the PLL to lock so there is no need
to wait for 3ms in the app. So shorten it like other busy wait.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Threads are being re-used for multiple runs, so it is better to
stop the threads before reusing the variables for new threads.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This application was initially intended to be a manual, interactive
sample, run by a user. However, it's also a useful real-world
integration test, to be run in automated CI systems. So, provide
a config suitable for such a usage: use local host machine as a
server (to not depend on availability and characteristics of an
Internet connection), and have a concrete completion criteria
(by limiting number of iterations; given that performance of TCP
is not to be not too high, limit it to just 1 for now).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Initially, this was intended to be a sample for manual "burnout"
testing, e.g. see if a device with it can run for 24hrs, or download
1GB of data, or similar.
It's however also useful for automated CI testing, but then we need
to have more specific completion criteria. So, allow to specify
number of download iterations via local Kconfig.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
To streamline management of multiple test configurations (which
now can go into separate config/overlay files instead of patching
source).
Note that now that this option is introduced, it must be set to
a correct value for any Zephyr config, thus we set it in
overlay-tls.conf. But the sample also supports building under a
POSIX environment (using Makefile.posix), which doesn't use
Zephyr's config system, so suitable defaults still should be
present in the C source file.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Fixes: #24158
The shell/fs sample was using APPLICATION_SOURCE_DIR before it has been
defined.
This has now been fixed to use the proper way of overlaying board
specific settings using boards folder.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
The lpcxpresso55s69 board has an mma8652 accelerometer which is
compatible with the fxos8700 driver in accel-only mode. Now that this
board has an i2c driver, include it in the platform whitelist.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Mention in websocket API documentation that the timeout value
is in milliseconds. Check timeout values properly using K_TIMEOUT_EQ()
macro.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use k_timeout_t internally, no change to user API.
Clarify the documentation of the timeout parameter that it is
in milliseconds.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
