Add PWM instances found on nRF54H20 and nRF54L15 devices,
so that PWM driver can be utilized on these.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
The valid range of hdop (horizontal diffusion of precision) goes
from 0-100000, but because we are using a uint16_t, we truncate
anything above UINT16_MAX.
This fix changes the size of the hdop member to a uint32_t, which
allows us to capture valid (but admittedly very poor) readings.
Signed-off-by: Rob Newberry <rob@zenomoto.com>
Moves a Kconfig that appears everywhere in the wrong place so that
it is enclosed if if statment check, so it only shows for device
that have the driver enabled
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
- update the console configuration defines references
- add missing header file with flash capabilities
- replace all console wait-until-ready calls by single one
Signed-off-by: Marek Matej <marek.matej@espressif.com>
The LL_APBx_GRPn_ReleaseReset clears reset bit in RCC,
however this bit is reset by default. Code that set
this bit was removed in previous commit
0856e99155
Keepint the autonomous clocks for STM32U5 family.
Signed-off-by: Adam Berlinger <adam.berlinger@st.com>
Magic constants throughout the code made this difficult to reason about,
especially with two different units of measurement (bytes and words) at
play.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
The RX FIFO size is in words, so needs to be subtracted from the total
memory size *after* it's divided by 4.
Fixes#70789.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
Add driver for ST7796s display. This is a MIPI DBI display controller,
with a frame memory of 320x480x18 pixels. Support for 4 wire SPI mode is
implemented using the MIPI DBI API.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Warn about potential device tree errors for cases when driver's
client tries to configure a pin as GPIO but which is not
in GPIO mode.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
It is impossible to perform flash reads during a flash write. When the
data to write to flash lies in the flash itself, it is buffered in ram
before writing.
Signed-off-by: Lukas Gehreke <lk.gehreke@gmail.com>
Move providing of the first buffer in uart_rx_enable from that
function to the callback which is called from nrfx_uarte_rx_enable
context. By doing this nrfx_uarte_rx_buffer_set is called when
RX configuration flags are already known to the driver.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Provide support for reading events longer than 127 bytes in
ST SPI protocol v1 by splitting them into several SPI transactions.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
Introduce NXP LCDIC driver using MIPI DBI class. This peripheral
supports 8080 and SPI 3/4 wire mode, although only SPI 4 wire support is
currently implemented. The driver supports DMA and interrupt driven
transfers.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The soc_secure_* function are used by the non-secure application
to access hardware resources which are mapped as secure.
Using these functions for hardware resources mapped as non-secure
is missleading.
We have some soc_secure_* functions which read FICR values.
In nRF91 and nRF53 platforms this made sense since FICR
has hardware fixed mapping as secure.
For nRF54 though the FICR has hardware fixed mapping as non-secure.
This change refactors the soc_secure.h to exclude the functions
which read FICR values from being included when FICR is mapped as
non-secure.
Also updates the hwinfo and ieee802154 drivers to adjust to this change.
Signed-off-by: Georgios Vasilakis <georgios.vasilakis@nordicsemi.no>
Adds an option that allows for locking all interrupts when reading
the data from this sensor, this can be used alongside systems like
Bluetooth to vastly increase chances of getting a reading from the
sensor successfully, at the risk of losing Bluetooth packets.
Signed-off-by: Jamie McCrae <spam@helper3000.net>
