This makes it easier to distinguish them from "true" undefined symbols.
Internally, all int/hex literals are treated as undefined symbols, which
always get their name as their value. The C tools work the same way.
The plan is to turn references to undefined Kconfig symbols into an
error later.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These cases weren't caught by the heuristic used by the warning added in
commit 6eabea3a7e ("Kconfiglib: Warn for unquoted string defaults"),
because "GPIO_0" has no lowercase characters in it.
Unquoted Kconfig values are are indistinguishable from reference to
(undefined) symbols in general. Quoting all string defaults will help
find "true" references to undefined Kconfig symbols, and makes it
clearer that the value is constant.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These symbols were removed by commit 4e8f29f319 ("gpio: Refactor the
mcux gpio driver to use dts"). The settings should come from DTS now.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add support for specifying the clock prescaler value for the HF timer
used for generating the PWM signals. This allows for lower timer
frequency and thus slower PWM signals (e.g. for use as servo
controller).
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
The nRF5x HF timer base frequency is 16 MHz, not 16777216 Hz.
The improved accurracy of the PWM signal was verified with an
oscilloscope on a BBC micro:bit.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
stm32cube SDK provides defines for IRQ line numbers.
It was not possible to use them, since enum where not supported
by IRQ_CONNECT macro.
Use them in order to get rid of zephyr manually coded IRQ lines.
They will later be replaced by device tree definitions when
made available
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
stm32cube SDK provides defines for IRQ line numbers.
It was not possible to use them, since enum where not supported
by IRQ_CONNECT macro.
Use them in order to get rid of zephyr manually coded IRQ lines.
They will later be replaced by device tree definitions when
made available
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
UART driver renamed to keep the same convention as SPI and TWI drivers.
All substrings: "UART_NRF5" in defines renamed to "UART_NRFX_UART".
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Replace all register defines and calls with Nordic nrfx HAL.
Simplification of uart shim - assumed only one uart instance.
Added parity bit to configuration options.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Add fixup info for PWM nodes on STM32F0/F1/F3/F4/L4 and remove the
conflicting Kconfig symbols to fully switch STM32 PWM to device tree.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
The nucleo_f334r8 uses STM32F3_PINMUX_FUNC_PA8_PWM1_CH1 inside its
pinmux but it is not defined anywhere.
Add the definition into the pinmux file to fix the build of
nucleo_f334r8 when enabling CONFIG_PWM.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
CONFIG_CLOCK_STM32_APB2_PRESCALER does not exist for STM32F0 as it was
removed from the RCC Kconfig by commit d0678201c3 ("drivers:
clock_control: provide support for stm32f0."). This will break the PWM
driver if compiled for STM32F0.
Conditionally disable usage of this symbol for STM32F0 as all PWMs are
on APB1 for this family.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
PWM1 / PWM15 / PWM16 and PWM17 on STM32F0 do not use the same clocks
compared to the other series.
Add the STM32F0-specific clocks where needed.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
Not all PWM clocks belong to the GRP1, for example TIM1 on STM32F0. Add
the group information to the macro to enable supporting these PWMs in
the future.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
The prescalers are currently hardcoded and are not user-selectable. As a
result, the frequency of the timer can be inadequate to the task. For
instance, the frequency of the 16-bit timers (prescaler 10000) is
usually too low to correctly generate of PWM of a few kilohertz.
Hardcoded prescalers are replaced by Kconfigs so the user can choose at
compile time. The default value of each Kconfig matches the hardcoded
prescaler, so the change will be transparent.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
All the PWM between 1 and 20 can be found on the STM32 depending on the
serie and the specific model. Add all the missing PWMs up to PWM20 to
plan for the future needs.
Tested on STM32L496 with available PWMs.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
The registration of each PWM differs only by a few details.
These differences can be factorized in order to create a generic
registration macro.
This has several advantages:
- Less code
- Easier to add new PWM
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
The nrf_rtc_timer used own method to calculate number of timer cycles
per tick. As the result value was different than the one used by
the kernel, the reported time was incorrect.
This commit fixes the problem described above by using global
sys_clock_hw_cycles_per_tick instead of custom RTC_TICKS_PER_SYS_TICK.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
Added support for circular linked list of DMA buffers
This patch checks the last block supplied by the application
and if the next pointer in the last block is valid, the tail
linked list item is linked to the head linked list item
to form a circular linked list
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
SPI driver has its own rx thread, select BT_RECV_IS_RX_THREAD.
This fixes build issue because of undefined CONFIG_BT_RX_PRIO.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
IRQ priorities for CAVS and DW were previously defined in Kconfig.
They are now defined via DTS and removed from Kconfig.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
If carrier is ON or OFF, then tell this information to upper IP stack
so that it can act accordingly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As stated in LIS2DH datasheet in section "5.1.1 I2C Operation",
in order to read/write multiple bytes on I2C it is necessary
to add the autoincrement bit to the subaddress field.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The lis2dh_burst_write used "bus" as an input parameters, while
inside "dev" was referred. Now variable names are aligned.
Signed-off-by: Evgeny Kalugin <evgeny.kalugin@intel.com>
Introduce a custom HCI driver for the native POSIX port, which opens a
HCI User Channel socket to the Linux kernel to gain access to a local
Bluetooth controller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The OVR condition in the Status Register requires a
particular sequence in order to be cleared. If not
done properly it stays set forever.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The issue was introduced by commit-id 27bdb83.
RTC_DIVIDER used to be 0 by default, now it's 1.
Fixes#8098
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The old way of erasing was not completely moved to the new SPI access
function, thus always sending useless dummy bytes that could lead to
error (aka: erasing more than requested).
Fixes#8065
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Each driver seemed to use their own Kconfig option to set the name for
their drivers. This makes writing example/test code difficult as each
one of them will have to special case for each of the supported
platforms.
Use a consistent CONFIG_WDT_0_NAME option in all drivers.
Fixes#8094.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Instead of relying on CONFIG_WDT_ESP32_DISABLE_AT_BOOT, use
CONFIG_WDT_DISABLE_AT_BOOT that's available for all watchdog timers.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This commit moves the bit timing (PROP, BS1, BS2 segments and SWJ)
from Kconfig to the device-tree and fixes issue #7933
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Add bit definitions and set M/N divider ownership in
i2s_initialize.
Changes to comply with coding guidelines
Changes to address review comments
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Added support for fractional division of reference clock to obtain
I2S bit clocks
For example:
If reference clock is 38.4MHz and
if the I2S format is 2ch, 32bits per channel, 48KHz sample rate,
the bit clock frequency has to be 2*32*48K = 3.072MHz
38.4MHz/3.072MHz = 12.5 (a fraction)
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
STM32 GPIO device initialization priority was set to
CONFIG_KERNEL_INIT_PRIORITY_DEFAULT
Following introduction of __ZEPHYR_SUPERVISOR__ macro (#6835),
drivers intialization order have been reordered which blocks
some use cases now.
Increase GPIO init priority to get it initialized before SPI
and avoid a deadlock.
Fixes#7663
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Don't hard code the syslog level to DEBUG, instead use the
CONFIG_SYS_LOG_ETHERNET_LEVEL setting like other ethernet drivers.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
Allow the application using DMA driver to register a callback for
a specific channel within the DMA device instead of one callback
per device.
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Native POSIX echo server sends malformed response to echo request of
size larger than 128 bytes (default size of each network data
fragment). Wireshark notices that by tagging echo request with "No
response seen". This commit fixes that issue.
Signed-off-by: Ruslan Mstoi <ruslan.mstoi@intel.com>
usb_dc_ep_read_continue can be called without usb_dc_ep_read_wait,
check if the current buffer is claimed by the controller
(transfer not finished) to prevent a faulty behavior.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Some serial tools such as 'minicom' send BS when press backspace,
not DEL, so delete char using BS or DEL.
Fixes: #7959
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
This is a rare but valid case when you request the controller to send
dummy bytes on your behalf (it saves memory as you don't need to provide
a valid buffer, just NULL and the numbers of dummy bytes as length).
Without it, user code can get stuck into interrupt loop.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The choice symbol LSM6DSL_EXT0_LIS2MDL was given a 'default' in
Kboards/arm/96b_argonkey/Kconfig.defconfig, but 'default' has no effect
on choice symbols, triggering a warning from Kconfiglib.
Instead of adding a default to the choice symbol, change the default of
the 'choice' itself by giving it name and adding the default in
Kconfig.defconfig.
This requires that we remove the default on the "base" definition of the
'choice', due to some messiness related to the Zephyr-specific
prefer-later-defaults behavior (see the 'Zephyr-specific Kconfig
behavior for defaults' section in the Board Porting Guide). Choices were
overlooked when that patch was added to the C tools, meaning choices
still prefer earlier defaults. The crux is that Kconfig.defconfig files
are included last.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
CAVS_ICTL_0_IRQ_PRI to CAVS_ICTL_3_IRQ_PRI and DW_ICTL_IRQ_PRI
are now defined in Kconfig. This addresses the issue #7811.
This was not throwing up any compilation error earlier as the IRQ
priorities are all hardwired in Xtensa and hence are unconfigurable.
They are dummy for Xtensa arch but may be applicable if used in some
other arch.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Convert couple of MSEC() calls to K_MSEC() as the timeouts
when using MSEC() are just too long.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
