Allocates segmented message buffers as slabs in a common pool for RX and
TX. This reduces memory requirements for both TX and RX, as TX messages
can be stored without the network and advertising buffer overhead, and
RX can use only the slabs it needs, instead of allocating a full size
segmented message. This approach also removes the need for decrypting
the segments for each retransmission, reducing overall processing load.
Slab based segmentation for tx also introduces queuing of segmented
messages, which allows the application layer to send multiple messages
to the same destination without violating Bluetooth Mesh specification
v1.0.1, section 3.6.4.1. This mechanism is provided through a flag that
blocks segmented messages to a destination which a message is already
being sent to until the previous message finishes.
This changes the SDU size configuration to a symmetrical
RX_SEG_MAX/TX_SEG_MAX pair of configurations, plus a new segment pool
side configuration. It also removes the binding between the TX_SEG_MAX
config and the advertising buffers, reducing the minimum advertising
buffer count from 6 to 3.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Split Link Layer implementation uses 80 bytes more ISR stack
in comparison to Legacy Link Layer, hence increase the
required ISR_STACK_SIZE for the BBC micro:bit and other
nRF51 QFAA SoC based mesh and mesh_demo samples.
Fixes#20414.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Reduce the RAM usage in two of the Bluetooth samples in order for them
to fit in the BBC Microbit's RAM.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Tick rate is becoming a platform tunable in the tickless world. Some
apps were setting it due to requirements of drivers or subsystems (or
sometimes for reasons that don't make much sense), but the dependency
goes the other way around now: board/soc/arch level code is
responsible for setting tick rates that work with their devices.
A few tests still use hard-configured tick rates, as they have
baked-in assumptions (like e.g. "a tick will be longer than a
millisecond") that need to be addressed first.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Minimal driver for ILI9340 LCD display driver including support
for adafruit 2.2" LCD display (1480)
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
Enable BT_SETTINGS and remove any custom flash access used for the
sequence number. We do settings_load() before bt_mesh_provision() and
use the return value from the latter to identity that settings_load()
had recoved a full configuration.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With upcoming ICs that are not in the nRF5x family, rename the flash
driver and all its dependencies from nrf5 to nrf.
Should also fix the issue introduced by f49150cab6 which broke the
assignment of the flash device due to a partial rename.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
2017-11-08 20:00:22 -05:00
Renamed from samples/bluetooth/mesh_demo/microbit.conf (Browse further)
