The network interface parameter for net_eth_get_vlan_tag() should
be the VLAN interface so use the search loop properly.
Earlier the main interface could be checked.
Add also test cases for this so that we can catch that the func
works properly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Remove IPSP support from the tree.
It has no maintainers, and is regularly broken. The fact that it's
nontrivial to set-up in linux makes it hard to fix reported issues.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
The commit adds dependency on Kconfig FLASH_PAGE_LAYOUT to subsystems
that really require it:
FCB, NVS, LittleFS
and removes direct selection from '*.conf' files where no longer
needed.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
There is no limitations for dwell time. Just add
valid condition for positive value. So , it's better
to remove those constraints.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
Add support for capturing arbitrary data via the cooked mode (sll)
capture API. The actual packet capture is done using net_capture_data()
function, the packet capture infrastructure does not need any changes.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Allow user to create a kitchen sink pseudo a.k.a any network
interface that one is only able to write to. This might seem
unnecessary, but it is possible to attach virtual network
interfaces on top of this pseudo interface. These virtual
interfaces could then process the data for example for
packet capture purposes.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add a recv callback to dummy API. After this it is possible to
receive data by a dummy network interface. This is only useful
if one attaches a virtual interface on top of the dummy one.
One such example is the cooked mode capture interface.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
eth_stats.h is using ethernet api but not including the header,
it must be working by luck in files that include it after
something else that includes ethernet.h, fix by just including it.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
There should be a particular defines which clarify the
use of that number. So, replacing numbers with defines
in wifi shell.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
Once Wi-Fi is associated few parameters like listen interval and
power-save mode cannot be changed. The state for association is
"ASSOCIATED" and not completed. Even after state transitions to
COMPLETE, it can still go back to other states, e.g., PTK/GTK renewal.
Fix the state check.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
The gPTP is not suppose to be run on top of VLAN and the
earlier support was just for testing purposes. Remove VLAN
support now after the VLAN overhaul.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Print also network interface index together with the pointer value
in order to get more useful information what is going on in the system.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Re-implement the VLAN support inside the network stack.
All the user facing APIs stay as is but internally the VLANs
are implemented using the L2 virtual interfaces.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Some compilers have trouble parsing variables directly after a case
statement.
Fixes: #70792
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
By using `getopt_state` to access `optarg`, offering a better alternative
to direct global `optarg` access.
This approach mitigates the risks associated with concurrent access to
the global variable.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
This change marks each instance of the `struct option` as `static const`.
The rationale is that `struct option` is a read-only variable.
By using `static const`, we ensure immutability, leading to usage of only
the `.rodata` section and a reduction in the `.data` area.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
This commit simplifies the access to structure members and omits
unnecessary variable initializations.
Specific adjustments include:
- Moving from pointer-based access (`(®d)->chan_info`) to
direct structure member access (`regd.chan_info`).
- Removing explicit initializations where not required.
- Removing excess backslashes '\' before '%' in the format string.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Refactor the IP tunneling support as the input callback was removed
in previous commit. The data will flow through the recv callback now
as expected.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The input callback was an unfortunate idea which just complicated
how the packet flows through virtual interfaces so removing it.
The data is passed normally through the recv callback from now on.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The function needs to loop through the virtual interfaces
tied to this physical interface.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Channel is mandatory for AP mode. It is processed only
if its less than or equal to three characters. Otherwise
we need to throw error for channel in AP mode.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
Dwell time Active or Passive is optional in wifi scan.
If user don't set the Dwell time value, it will be set
as 0. We are adding a range check in scan extensions
for dwell time. So need to set default values.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
During stress test with WiFi connect, disconnect, ping and throughput
traffic, ARP table updating failed issue may occur.
In arp_prepare(), if packet allocate failed, should add the arp
entry back to arp_free_entries, to avoid this entry is leak forever.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
Convert various networking subsystem files to use ARRAY_FOR_EACH
macro to make the looping more robust.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The netmask should be tied to the IPv4 address instead of being
global for the network interface.
If there is only one IPv4 address specified to the network interface,
nothing changes from user point of view. But if there are more than
one IPv4 address / network interface, the netmask must be specified
to each address separately.
This means that net_if_ipv4_get_netmask() and net_if_ipv4_set_netmask()
functions should not be used as they only work reliably if there is
only one IPv4 address in the network interface.
The new net_if_ipv4_get_netmask_by_addr() and
net_if_ipv4_set_netmask_by_addr() functions should be used as they make
sure that the netmask is tied to correct IPv4 address in the network
interface.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This ensures that the configured link address is
at least as big as the part of it that is used.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
Since PR, PR_SHELL, PR_ERROR, PR_INFO, and PR_WARNING already have
an embedded `sh` NULL check, we can remove the change from PR #68809.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
This change reduces the memory footprint by changing the data type of
`valid_5g_chans_20mhz` from `uint16_t` to `uint8_t`.
Additionally, since the maximum channel number for 5GHz Wi-Fi is 177,
it can fit within the `uint8_t` range.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
This flag indicates that only passive transmissions are allowed in that
channel for that regulatory domain.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Fix the dead lock between rx_q and tx_q thread.
When tx_q thread prepares to send ARP packet, it might get
the net_if_tx_lock in net_if_tx(), then in net_arp_prepare(),
it will try to get the arp_mutex.
At the same time, if the rx_q thread receives an ARP reply
packet, in arp_update(), it will get the arp_mutex first,
and flush the packets in arp pending_queue and try to get
the net_if_tx_lock. Then the dead lock occurs, two threads
stuck and all the packcets can't be freed.
In arp_update(), taking the net_if_tx_lock first then taking
the arp_mutex can fix this issue.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
By default variable context.sh is set to NULL. If any net_mgmt
event will be called when the variable has default value, there
will be a system exception.
Signed-off-by: Wojciech Slenska <wsl@trackunit.com>
WIFI scan result shows junk character in SSID because of
the length of ssid is maximum(32 character) which leads
to buffer overflow. It required one character for null
terminator ‘\0’.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
As defined in IEEE802.1AS-2020 ch. 10.2.12.2.1, the port identity
of an MDSyncSend structure sent from a port shall be set to the
port identity of the sending port according to and ch. 8.5.2.
This commit replaces the port identity before forwarding a sync.
Fixes#68385
Signed-off-by: Manuel Schappacher <manuel.schappacher@hs-offenburg.de>
Additionally, replace the local print(sh, level, fmt, ...) macros
with PR, PR_ERROR, and PR_WARNING macros.
Then remove the print(sh, level, fmt, ...) macros.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Replaced direct shell_fprintf calls with PR, PR_ERROR, PR_INFO
and PR_WARNING macros.
This change simplifies the code by using predefined macros.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Moved 'scan_result' from a standalone variable into the 'context' struct
to enhance code optimization.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
This commit introduces a local variable 'sh' to store 'context.sh' for
use with the 'shell_fprintf' function.
By doing so, we avoid the repeated dereferencing of 'context.sh',
thereby reducing the code footprint.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
For a Wi-Fi station the connect API supports both band and channel
configuration, but for a shell command either channel or band makes
sense, so, overload the channel field to support band.
Rejig the band and channel validation to support all modes.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
