Update gpio drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on devicetree.
We remove 'depend on' Kconfig for symbols that would be implied by
the devicetree node existing.
Signed-off-by: Kumar Gala <galak@kernel.org>
In #40140, all on-chip gpios where made to use `CONFIG_GPIO_INIT_PRIORITY`.
The lmp90xxx and sx1509b are off-chip gpios. This commit reverts those
changes for these two devices.
Signed-off-by: Ryan McClelland <ryanmcclelland@fb.com>
Refactors all of the on-chip GPIO drivers to use a shared driver class
initialization priority configuration, CONFIG_GPIO_INIT_PRIORITY, to
allow configuring GPIO drivers separately from other devices. This is
similar to other driver classes like I2C and SPI.
Most drivers previously used CONFIG_KERNEL_INIT_PRIORITY_DEFAULT or
CONFIG_KERNEL_INIT_PRIORITY_DEVICE, therefore the default for this new
option is the lower of the two, which means earlier initialization.
Driver-specific options for off-chip I2C- or SPI-based GPIO drivers are
left intact because they often need to be initialized at a different
priority than on-chip GPIO drivers.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
enable the interrupt functionality for sx1509b gpio expander,
when the CONFIG_GPIO_SX1509B_INTERRUPT config is enabled.
The gpio pin used for interrupt should be configured in the
device tree sx1509b node before enabling the interrupt
configuration.
Signed-off-by: Viraaj Somayajula <sviraaj@zedblox.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
All GPIO controller drivers support DTS so we can select HAS_DTS_GPIO
at the GPIO driver subsystem level rather than for each specific driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enable the gpio_sx1509b driver by default when a "semtech,sx1509b"
compatible node is enabled in devicetree.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Most of these are from source'ing a file within an 'if GPIO', and then
adding another 'depends on GPIO' within it.
'if FOO' is just shorthand for adding 'depends on FOO' to each item
within the 'if'. There are no "conditional includes" in Kconfig, so
'if FOO' has no special meaning around a 'source'. Conditional includes
wouldn't be possible, because an 'if' condition could include (directly
or indirectly) forward references to symbols not defined yet.
Tip: When adding a symbol, check its dependencies in the menuconfig
('ninja menuconfig', then / to jump to the symbol). The menuconfig also
shows how the file with the symbol got included, so if you see
duplicated dependencies, it's easy to hunt down where they come from.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Every board that uses dts-enabled i2c drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_I2C_DEVICE and
HAS_DTS_I2C.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Selects HAS_DTS_GPIO in various gpio drivers that already support dts,
similar to how we select HAS_DTS_SPI in spi drivers and HAS_DTS_I2C in
i2c drivers.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
When CONFIG_GPIO_SX1509B was not set, the related Kconfig options
were still showing up in .config. Let's make them depend on
GPIO_SX1509B so they can go away when not being used.
Signed-off-by: Michael Scott <mike@foundries.io>
Consistently use
config FOO
bool/int/hex/string "Prompt text"
instead of
config FOO
bool/int/hex/string
prompt "Prompt text"
(...and a bunch of other variations that e.g. swapped the order of the
type and the 'prompt', or put other properties between them).
The shorthand is fully equivalent to using 'prompt'. It saves lines and
avoids tricking people into thinking there is some semantic difference.
Most of the grunt work was done by a modified version of
https://unix.stackexchange.com/questions/26284/how-can-i-use-sed-to-replace-a-multi-line-string/26290#26290, but some
of the rarer variations had to be converted manually.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Piggyback a missing 'source "drivers/gpio/Kconfig.imx"'. This file
wasn't included anywhere previously.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Adds a driver for SX1509B I2C GPIO chip. This driver only supports the
basic GPIO features and does not currently implement the LED driver and
keypad matrix features.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
