The CMSIS module glue code was part of arch/ directory. Move it to
modules/cmsis, and provide a single entry point for it: cmsis_core.h.
This entry header will include the right CMSIS header (M or A/R).
To make this change possible, CMSIS module Kconfig/CMake are declared as
external, allowing us to add a new Zephyr include directory.
All files including CMSIS have been updated.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Updated the code to to invoke reset using PCR block
z_mchp_xec_pcr_periph_reset() instead of resetting
using I2C Configuration register
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
We get a compiler warning in this code with arm clang due to using
the wrong enum type for the variable. The enum should be of
type `enum periph_clk32k_src` so replace VBR_CLK32K_SRC_PIN_XTAL
with PERIPH_CLK32K_SRC_PIN_XTAL.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
Program the right trim control register for mec150x.
This fixes uart debug console output issue.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add support for Microchip MEC15xx to the XEC clock control driver.
MEC15xx 32KHz clock support uses the same 32KHz source for both the
PLL and peripherals. MEC152x does not include the PCR clock monitor
present in MEC172x. MEC15xx and MEC172x support internal silicon
oscillator, parallel and single ended crystal inputs, and the
32KHZ_PIN input. MEC152x supports fall back to internal silicon
OSC when VTR and 32KHZ_PIN are turned off. Therefore in MEC152x the
internal silicon oscillator can only be disabled if using an external
32KHz which is always on. For MEC152x the driver will only use the
PLL source clock device tree value.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Fix Microchip XEC clock control driver single-ended XTAL2 pin
initialization. Add support for external 32KHZ_IN pin as a
clock source including PINTRL to switch the GPIO to 32KHZ_IN
function. Add device tree option to disable internal silicon
oscillator if it is not required by the configuration. Add
device tree tuning options based on crystal and board layout.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Microchip MEC172x CPU and fast peripheral (QMSPI and PK) are
clock source is based upon an OTP setting. Add logic to adjust
clock source based on OTP value. If the OTP value is ever changed
this fix will allow calcluation of correct clock rate.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Refactors all of the clock control drivers to use a shared driver class
initialization priority configuration,
CONFIG_CLOCK_CONTROL_INIT_PRIORITY, to allow configuring clock control
drivers separately from other devices. This is similar to other driver
classes like I2C and SPI.
Most drivers previously used CONFIG_KERNEL_INIT_PRIORITY_OBJECTS or
CONFIG_KERNEL_INIT_PRIORITY_DEVICE, therefore the default for this new
option is the lower of the two, which means earlier initialization.
The even lower defaults for STM32 and Arm Beetle are preserved by
SoC-family level overrides.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Implement a clock control driver for Microchip MEC172x handling
configuring the 32 KHz input sources for the PLL and peripheral-32k
clock domains. MEC172x differs from MEC152x. MEC152x had one 32K source
for both PLL and peripherals. MEC172x allows the two domains to use
independent 32 KHz sources. Device tree updated to provide addresses
of hardware used by the driver.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
