For ztest twister would parse the symbol information that was
generated as part of the build (zephyr.symbols). However the format
of the zephyr.symbols files is highly dependant on the toolchain.
Move to using pyelf to parse the symbol information directly from
zephyr.elf instead so that this works regardless of toolchain.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
By default there is only CONFIG_LOG_FUNC_NAME_PREFIX_DBG=y enabled. When
both Bluetooth (CONFIG_BT=y) and logging (CONFIG_LOG=y) subsystems are
enabled, then other CONFIG_LOG_FUNC_NAME_PREFIX_{INF,WRN,ERR}=y options are
pulled in as well using an 'imply' Kconfig command indirectly from
`CONFIG_BT_LOG`. This behavior was introduced recently as part of
commit af01a0f313 ("Bluetooth: Logging: Move all logging symbols
together") with no explicit reason provided.
Pulling in LOG_FUNC_NAME_PREFIX_* options automatically with (CONFIG_BT=y
&& CONFIG_LOG=y) blows up flash usage. As an example of downstream project
(nRF52840-based, with Bluetooth and WiFi connectivity), it increases flash
usage from 473668 bytes to 487856 bytes. This seems "only" 3% difference,
but this is actually a lot when there is no good reason why this happens.
Downstream users quite often compare flash sizes of subsequent Zephyr
releases and this 3% footprint increase might be a blocker at some point.
Additionally, it is not trivial to find the root cause of footprint
increase for most (non-expert) users.
The reason why there is so much footprint overhead because of
CONFIG_LOG_FUNC_NAME_PREFIX_*=y is because each function in the
codebase (be it Zephyr or downstream application) that contains logging
macros (LOG_{DBG,INF,WRN,ERR}()) is bloated because the function name has
to be included in the output image.
Remove 'imply LOG_FUNC_NAME_PREFIX_*' commands from 'menuconfig BT_LOG'
option, so that flash usage does not increase too much. Those logging
options are not enabled by other subsystems, so Bluetooth should not be an
exception here.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
RPR Client doesn't send RPR_OP_LINK_REPORT and therefore it can't wait
for it using ack ctx. It should have been RPR_OP_PDU_OUTBOUND_REPORT
to cover a case where Outbound PDU transmission failed. But in this case
the link status will be non equal to BT_MESH_RPR_SUCCESS (see pb_error in
rpr_srv.c) and the link state will be set to idle. And the client will
reset the link together with ack ctx.
When bearer user (provisioner.c) sends an Outbound PDU, it uses the
callback (see bt_mesh_prov_send in provisioner.c) to send a next PDU,
but it doesn't check the error code even though it is provided through
the callback. Therefore calling the callback with error code would
require error handling in provisioner.c.
With ordinary provisioning PB-ADV doesn't call the callback in case of
error, but closes the link by timeout if doesn't receive ACK (see
prov_send_adv in pb_adv.c). PB-GATT always calls the callback with
error code 0 once the PDU is transmitted (see buf_send in pb_gatt.c).
Thus this change aligns RPR Client implementation with other bearers.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
When central is sending SMP Pairing Request is it unknown if
pairing will be legacy or LE SC so set OOB flag if any OOB
data is present and assume to peer device provides OOB data
that will match pairing type.
This was affecting following qualification test cases:
SM/CEN/OOB/BI-01-C
SM/CEN/OOB/BV-01-C
SM/CEN/OOB/BV-03-C
SM/CEN/OOB/BV-09-C
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Secure Channel Base Key (SCBK) is a secret key used to derive the session
keys used to encrypt and decrypt OSDP packets. Secure coding practice
requires us to clear such sensitive data from stack once we are done
needing it. This patch addresses this issue.
Signed-off-by: Siddharth Chandrasekaran <sidcha.dev@gmail.com>
OSDP secure channel message blocks are terminated with a 0x80. This means
that even for zero length messages, we would have at least one block of
encrypted data to decrypt (since message blocks are rounded up to the next
16 byte boundary). The current length assertion checks for 16 byte
alignment but a malicious peer could send a specially crafted packet with
zero length blocks. Fix this issue by adding check for length == 0 case.
Signed-off-by: Siddharth Chandrasekaran <sidcha.dev@gmail.com>
HID readers are responding to a KEYSET command with an ACK in plaintext
instead of using the current session keys to acknowledge this command
(which is the reasonable thing to do as the command itself was received
encrypted with the old key). Since the spec doesn't say anything about
this, both methods are technically correct.
Make changes to CP so it allows ACKs in plaintext for KEYSET command in
particular and make the PD implementation do this too as it makes the code
look cleaner there (perhaps HID did it for the same reasons :D).
Signed-off-by: Siddharth Chandrasekaran <sidcha.dev@gmail.com>
If command or reply has no data, PD "should" use secure message types
SCS_15 or SCS_16. But some PD seem to not implement this correctly. We
will be tolerant towards those faulty implementations.
Signed-off-by: Siddharth Chandrasekaran <sidcha.dev@gmail.com>
OSDP command KEYSET is used to set the secure channel base key for all
connected PDs. This key is then used to derive the session keys for each
secure channel session. When the app wants to set the this key, it has
to issue a command and then both the CP/PD has to be notified of this
change so they can store this key in a non-volatile medium for future
operations across power cycles.
The current implementation of OSDP had limited support for key
management. This patch adds all the bells and whistles needed to handle
keyset command/event in the CP/PD application.
Signed-off-by: Siddharth Chandrasekaran <sidcha.dev@gmail.com>
Hoisting a `length--` helps simplify a lot of code which has ad-hoc -1s
in a bunch of places. Also, fix some formatting issues and remove
unnecessary log lines.
Signed-off-by: Siddharth Chandrasekaran <sidcha.dev@gmail.com>
Struct sh_telnet should be initialised before first function call.
Right now there is a possibility that telnet_accept function will
be called before memset.
Signed-off-by: Wojciech Slenska <wsl@trackunit.com>
Add a new backend for Host Commands that uses UART. The backend bases
asynchronous UART API.
The UART backend is mainly used by FPMCU.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
There were a missing NULL check for the track segment in
paused_state_command_handler when performing the segment
operations.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The discovery parameters may contain values from previous
discovery calls. The simply and future proof solution to
this is to simply memset it before using it.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
If the subscribed callback is called with value_handle = 0,
then it should not be treated as a subscription complete.
This will happen when bt_mcc_discover_mcs is called, as
reset_mcs_inst unsubscribed to all characteristics before
discovering again.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add macro BT_MCS_VALID_OBJ_ID to verify the OTS Object
ID before attempting any OTS operations.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
If server or bootstrap writes a lifetime value less than
configured default lifetime, client will automatically overwrite
the value with default one.
This gives better control for the application where client
behaviour is fine tuned on the Kconfig, but default values
from bootstrap server cannot be fine-tuned.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
This patch allow to use isotp use_fixed_addr feature
with CAN identifier which not match SAE J1939 format.
Signed-off-by: William MARTIN <william.martin@power-lan.com>
Extend the invert command to run cfb_invert_area when given four arguments.
Make a change to invert the screen immediately in case of run invert
without arguments.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Add the `draw text` command to execute the `cfb_draw_text()` API.
The command is similar to the `print` command. The difference is
`draw text` can render to coordinate that is not on tile boundaries.
The command is not run `cfb_framebuffer_clear()`,
So it allows rendering appendiceal with keeping already drawn image.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Add cfb_draw_text() API for rendering text.
It is similar to cfb_print(), the difference is cfb_draw_text() accepts
coordinate that is not on tile boundaries and don't wrap the line.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Implements dot-by-dot font rendering to make cfb_print() able to
draw text even at a coordinate that is not on tile boundaries.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
cfb_print does not modify either address and contents of
the pointer that is pointing drawing text.
Thus, it can add a const modifier.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
cfb_framebuffer_finalize() invert the framebuffer, and it still
leave as inverted after executing the function.
It restores the framebuffer at the end of the cfb_framebuffer_finalize()
for the continued drawing.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
dev and clear_display parameter are unused and only
the framebuffer was cleared. A condition which calls
cfb_framebuffer_fanalize when clear_display is
true is implemented. Then not only the buffer,
but buffer and display are cleared.
Signed-off-by: Dölker Kim <KDoelker@baumer.com>
This function had only one use in SenML CBOR formatter and it
contained some specific tweaks, so move the function to be a
static member of that module.
Fixes#53674
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Fail compilation when incorrect configuration is detected, i.e. when
SHELL_BACKEND_SERIAL_CHECK_DTR is set but UART_LINE_CTRL is not set.
Use periodic timer to wait for DTR instead of waiting in uart callback
to prevent blocking caller workqueue and/or sleeping in ISR.
DTR check was only ever supported with interrupt driven backend so add
appropriate depends on to Kconfig.
Fixes: e9f238889b ("shell: uart: Add waiting on DTR signal before
sending data")
Fixes: #47120Fixes: #54705
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
When LwM2M engine is paused, stop functionality just
marks the intent and when we resume, it will send the
de-registration if that was requested.
Otherwise it will stay in SUSPENDED state until resumed
and then goes into ENGINE_DEREGISTERED -> IDLE.
This also removes the blocking loop from lwm2m_rd_client_stop().
It does not need to block because lwm2m_rd_client_start()
is already checking if client is in IDLE.
Fixes#56254
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Various bluetooth tests fails to link because bt_le_ext_adv_set_data
can't be resolved. Solve this by adding a check CONFIG_BT_EXT_ADV
around use of bt_le_ext_adv_set_data.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
Instead of passing the test parameters to the websocket function, by
casting the pointer to integer (which may not work on 64-bit platform
due to int/pointer size mismatch), let the test allocate a file
descriptor, and initialize it with test context. The tested functions
expect a file descriptor as an argument anyway, so it's a more intuitive
approach.
The conditional test code within WS implementation can retrieve the test
context by using FD APIs to obtain the object represented by the FD.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Added using LOG_DEFAULT_LEVEL kconfig option in log module
template for assigning the default log level to newly created
module instance, instead of assuming always INFO level.
Signed-off-by: Kamil Kasperczyk <kamil.kasperczyk@nordicsemi.no>
C only permits labels on statements, not declarations. Separate the
declarations from the assignments so that the labels can target
statements instead.
Signed-off-by: Keith Packard <keithp@keithp.com>
Some cases, especially those dealing with faults need to inject output
manually, so provied a macro for special case.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
When lfs mount fails and there is no formatting requested, the return
code must be translated to errno before being passed to the application
layer.
Additionally, only log a warning that the FS will be formatted, when the
system is not read-only.
Fixes#56378
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
The PAST sender needs to support periodic advertising
and the PAST receiver needs to support periodic advertising
sync.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
