Fix the following device tree warnings:
unit-address and first reg (0x20000) don't match for iccm@0
unit-address and first reg (0x80010000) don't match for dccm@80000000
Since the em_starterkit_em7d_normal has a different base address for
iccm & dccm, and most of the em_starterkit variants have different sizes
for iccm & dccm. Just define the nodes in the specific
em_starterkit*.dts file and remove them from emsk.dtsi. This removes
the issue reported in the warning.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since there are times that we include a base .dtsi file and change the
reg address we tend to end up with warnings that the reg address and
unit-address don't match. To handle this introduce a simple DT_ADDR(x)
macro that will prepend '0x' to a 'unit-address' style address.
#define DCCM_ADDR 80000000 /* in unit-address format */
dccm0: dccm@DCCM_ADDR {
reg = <DT_ADDR(DCCM_ADDR) 0x1>;
...
};
This allows the dts file to override the value of DCCM_ADDR and than to
have the unit-address of the node and the reg address match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Create an SoC definition for the Audio DSP on Intel Apollolake
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds a simple binding for the Cadence Tensilica Xtensa LX4
CPU. File originally from the LX6 binding.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Update to use new API for GPIO pin configuration and operation. Fix
invalid arithmetic on void pointer. Convert to support devicetree.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update to use new API for GPIO pin configuration and operation. Fix
invalid arithmetic on void pointer. Mark all CC2520 GPIOs as required
in binding.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update the lora/sx1276 driver to the new GPIO API, using configured
active level and the replacement interrupt and active-sensitive set
APIs.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Document and assign write-protect signal as active low, and use the
active-sensitive API to control it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update devicetree sources and bindings, switch to new GPIO API. Use
devicetree property name to identify interrupt signal.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API. Update all
devicetree bindings to add INT signal active level. Document active
level.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update sample overlays. Add GPIO flags to configuration state.
Refactor to split out setup/handle/process phases. Switch to new API
replacing callback dis/enable with interrupt dis/enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The offset and the number of pins were swapped causing an error when a
64-position left shift was generated to calculate the pin mask.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a config structure for each port and use the devicetree GPIO pin
count to initialize it. Simplify device initialization by using
instance number as only variation point.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Almost all drivers support 32 pins, though some support less.
Eventually this should be specified in every SOC binding, but until
then provide a default so GPIO drivers can be updated to use this.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Since this was converted to the setup/handle/process idiom in master
the conversion is straightforward.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commit updates the HMC5883L driver to use the new GPIO API.
Also add a note explicitly describing the active state of the DRDY
pin in the binding file.
Tested on frdm_k64f.
Signed-off-by: Kevin Townsend <kevin@ktownsend.com>
Update sample overlay for missing chip select and to deconflict with
UART TXD. Add GPIO flags to configuration state. Replace callback
enable with interrupt enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a sample overlay. Add GPIO flags to configuration state. Replace
callback enable with interrupt enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Converts the fxas21002 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on the hexiwear_k64 board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This maps devicetree GPIO phandle arrays from the full controller pin
range to the sub-controllers required by Zephyr's limit of 32 pins per
controller device.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This breaks down the GPIO controller definition in DTS into
multiple entries. This allows these controllers to be
referenced by other DTS, and test board overlay files.
And also we can remove the entries in the dts fixup file.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There were complains about the unit-address and first reg
not matching. So update the DTS file to match.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Converts the fxos8700 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on frdm_k64f and rv32m1_vega_ri5cy boards. The latter verifies
that the reset output works correctly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converts the usdhc driver to the new gpio api. Updates the
device tree for the mimxrt1050_evk board to set appropriate active
high/low polarity for the power and card detect pins.
Note that the driver doesn't actually support interrupts yet. It
initializes a gpio callback for the card detect pin, but never actually
enables the gpio interrupt. This incomplete behavior is left as-is,
since the purpose of this patch is only to convert the driver to the new
gpio api, not to add new features.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
