In multi-image environment, after jump to the image we can have UART in
unexpected state. Reset UART to default state to make sure that UART is
initialized properly and won't cause system to crash or hang.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
Update serial drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on devicetree.
We remove 'depend on' Kconfig for symbols that would be implied by
the devicetree node existing.
Signed-off-by: Kumar Gala <galak@kernel.org>
This is the dma V2bis which is particular DMA V2 instance for
stm32F1 and STM32L1 soc series. This DMA does not use the dma slot
Otherwise it is similar to version V2.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add initial implementation of the uart async api
for stm32 mcus. This uses the dma controller
in normal mode for reception. In addition, to detect
reception of bytes we enable the idle line detection
interrupt.
Signed-off-by: Shlomi Vaknin <shlomi.39sd@gmail.com>
Signed-off-by: Jun Li <jun.r.li@intel.com>
Signed-off-by: Giancarlo Stasi <giancarlo.stasi.co@gmail.com>
Replace use of Kconfig UART_X symbols by calls to DT API.
Clean driver from symbols definitions
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Added device tree nodes and associated headers for
defined uarts on the stm32g0 and stm32g07x 8x parts.
Tested with uart on stm32g071rb disco board with usart3 going to stlink.
Using shell.
Signed-off-by: Kieran Levin <ktl@frame.work>
Same deal as in commit eddd98f811 ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for the remaining cases outside defconfig
files. See that commit for an explanation.
Will do the defconfigs separately in case there are any complaints
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
In Kconfig.stm32, all UART port symbols were defined with a dependency
on symbol UART_STM32. This is redundant since they are located under
if UART_STM32 condition.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following recent renaming of STM32 UART Kconfig UART symbols,
LPUART was named as UART_LPUART_1.
Rename to LPUART_1.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32 uart Kconfig instance flags were not following
same naming scheme than other drivers (i2c, spi, ..)
Update driver to use UART_X instead of UART_STM32_PORT_X
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
LPUART (Low-power UART) peripheral is just like ordinary U(S)ART
which lives in a separate clock/power domain.
Therefore already existing code could be reused as is
almost entirely.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Replace specific STM32F1 references with generic STM32 ones.
Use generic names like U(S)ARTx for instances which have different
naming across STM32 families.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
As not all drivers support interrupts we don't have a means to know if
we can allow UART_INTERRUPT_DRIVEN to be enabled and thus various
Kconfig options that select UART_INTERRUPT_DRIVEN. Some drivers have a
interrupts, however not all do. So introduce a Kconfig option to let us
know what the driver actually supports.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we can utilize label in the device tree we can convert to
getting the device name for the STM32 UART out of the device tree
instead of from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for U(S)ART 4 to 10 that can be found at least on some
members of the STM32F4 family.
Change-Id: Ie870492511f885005cf023040e498bd4d800e807
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Now that all STM32 platforms are using device tree we can remove the
handling for !HAS_DTS from the serial driver.
Change-Id: Ifafc283f2509dd9a438f321e0b647720d4f13810
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Currently the entries for STM32 UART ports are at the same level than
the top menuconfig UART_STM32. As a result they are mixed with other
configs in the "Serial Drivers" menu.
Use if/endif grammar to put these entries under a dedicated STM32
submenu.
Change-Id: If28945204b801578d29f8cce7c2370ca3c2737a1
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
This patch adds device tree support to the STM32 UART driver. The base
address, interrupt, and interrupt priority values can now come from DTS.
Change-Id: I3c383da8b200037601ecb2dc087f99ef103761bb
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There was a misalignment between Zephyr UART device numbering and
SoC UART IP. Device "UART_1" was mapped to IP USART_2, which could
be confusing for user.
This commit allows to align "UART_1" to IP USART_1.
Change is propagated to all STM32F103RB/STM32F401RE based boards and
respective pinmux drivers
Change-Id: Ia8099dfeec7b9c0c686c2a58ccb4dbb1a55b6537
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use CONFIG_SOC_FAMILY for the top level SoC family. A family
will have different SoCs or different SoC series with multiple
SoCs.
Adding the Family string to the config variable to avoid confusion
between actual SoCs and families and to prevent name collisions.
Change-Id: Ic99a2c1df7850dee3a45641027af82464dd6fadb
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The patch extends STM32 serial port driver with support for IRQ API of
the common UART port driver API.
Change-Id: If105e8528ea4ed4181cc4af0c97c24aa874e69e0
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
Add driver for U(S)ART ports on STM32 MCUs. The driver implements basic
RX/TX functionality. Data transmission is implemented using polling. The
driver configures the port to use 8bit data transmission, 1 stop bit, no
parity control.
The driver exposes a public uart driver API and registers a single UART
device 'UART_0'. The device binds to USART1 peripheral and performs
required pinmux and clock control configuration. The device can be
initialized at the PRIMARY level, with default device priority.
The driver has been verified to work with a sample Hello World
application on a STM32F103 series MCU.
Change-Id: Iae103fcd8d2fb0a6c173cf141a68e17791255aab
Origin: Original
Signed-off-by: Maciej Borzecki <maciek.borzecki@gmail.com>
