All pins from the existing pin init in
drivers/pinmux/k64/pinmux_board_hexiwear_k64.c were brought forward.
Jira: ZEP-1393
Change-Id: I3eb38dc435809cb7997d5884ff63bf8dd1e54720
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Some pins were not brought forward from the existing pin init in
drivers/pinmux/k64/pinmux_board_frdm_64f.c because they do not appear to
be used anywhere and it increases power consumption to enable them. For
example, 6 pins were enabled as analog inputs, but there is not yet an
ADC driver for the k64. The pins that were not brought forward are:
* PTA 0-2
* PTB 2,3,9-11,23
* PTC 2-4,10,11
Jira: ZEP-1393
Change-Id: I7410f6d993bd0a4df8f80df72e84def73bcf74cc
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch updates defconfig file on V2M Beetle board in order to enable
clock_control and watchdog by default.
It defines also a dummy LED in order to maintain compliance with the
Zephyr test environment.
Jira: ZEP-1300
Change-Id: I40ae4cb19e79ff24e1e351a2185a7191f03664d1
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Add board support for the Nucleo64 L476RG development board.
Change-Id: Ibb5424bc936c67a5d96855617202136d7dea772c
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
There was a misalignment between Zephyr UART device numbering and
SoC UART IP. Device "UART_1" was mapped to IP USART_2, which could
be confusing for user.
This commit allows to align "UART_1" to IP USART_1.
Change is propagated to all STM32F103RB/STM32F401RE based boards and
respective pinmux drivers
Change-Id: Ia8099dfeec7b9c0c686c2a58ccb4dbb1a55b6537
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add defaults for the fxos8700 sensor, including which i2c instance, the
slave address, and interrupt pin.
Change-Id: Ib8a1e451ddfd84d2b2f19b0da846854acc969dcf
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add defaults for the fxos8700 sensor, including which i2c instance, the
slave address, and interrupt pin.
Change-Id: I4b0255308fd5c9b7c43f0f22e8ce2fe86c5e7011
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Make the blinky application work with this board.
Change-Id: Ibe8d310229e2ff79a2164b7c8f16e7ba3ee0b8c2
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add board support for ARM V2M Beetle platform.
ARM V2M Beetle board is build around the ARM Beetle Cortex-M3
based processor.
The support has been tested in nanokernel mode with the bringup
application that will be pushed with a future patch.
Jira: ZEP-1245
Change-Id: Ib05a40c072f10149e692283177387cf2cfe32f66
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The Quark SE C1000 BLE Core is a nRF51822-QFAA, with 16kB of RAM and
256kB of flash. The configuration is otherwise similar to the Arduino
101 BLE, except that the UART RTS pin is the same as that used by
nrf51_pca10028.
Change-Id: I88cb18876bdde65abcf9a499894f70802046c824
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Board uses nRF51822-QFAA, with 16kB of RAM and 256kB of flash.
The UART has no hardware flow control pins.
Change-Id: I16ffeee15a1f5714c695dc8b38e77fb134ea7a0f
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Change the default Bluetooth UART device name to the UART connected to
the arduino header. This allows using the frdm_k64f with a frdm_kw40z
shield board.
Change-Id: Id22950f0a48a7c95bcddc6f1ec044f7a37cb9b72
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Change the default Bluetooth UART device name to the UART connected to
the on-board kw40.
Change-Id: I2ae981bce31a58aed4dc6d3c378fc6f6a0bec76f
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The pinmux configuration is done during board initialization.
This was validated using the following Zephyr apps:
- samples/hello_world
- samples/philosophers
- samples/drivers/uart
- samples/shell
UARTA0 is currently supported.
Change-Id: I85727c622d4d42183cc9f2f8b43d653e245dd17e
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Leverages the pinmux.c file generated by the TI PinMux utility
to enable UART pins. The pinmux configuration is used in lieu of a Zephyr
pinmux driver, and is called during board initialization.
UARTA0 is currently supported.
Jira: ZEP-1109
Change-Id: Iddb01f79043af034886859b608b7b6aadf844e53
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Added Kconfig and makefiles to be able to build a Zephyr application
on Linux/gcc, and load via OpenOCD.
Validated by running the hello world, and philosophers microkernel
samples, and stepping through the code in gdb.
Jira: ZEP-1109
Change-Id: If5d3e7b1a8ecf5ecf6a00f147742b3bc5716190f
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The k64 SoC has multiple instances of many peripherals, but which
instances can actually be used depends upon the board design and pinmux
configuration.
Move all instance-specific default driver configurations from the SoC to
the boards (frdm_k64f and hexiwear_k64). Default driver selection
remains in the SoC (e.g., enable the KSDK I2C driver when I2C is
enabled).
This paves the way to support different driver defaults for the
frdm_k64f and hexiwear_k64 boards, but it does not yet change any of the
default values; it only changes where the default values get set.
Change-Id: Id9ed898762eb400ecefeac91ae4dce66da05622d
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
STM32Cube uses SoC defines made to reflect HW heterogeneity that
should be taken into account by SW.
Aim of this commit is to adapt values used by Zephyr to the same
diversity. This will help create new SoC values only when justified
by a real hardware difference that should be taken into account
by software.
For instance, for SoC stm32f401re following define is used:
*STM32F401xE
Which means:
*Same SW could be used on STM32F401RE and STM32F401CE:
same CONFIG_SOC could be used
*Different SW should be used on STMF401RE and STM32F401RC:
different CONFIG_SOC should be used
This change focuses on stm32f4xx series.
Change-Id: I56ff4d1815d09747cf722385532eb2dcbdf37b44
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32Cube uses SoC defines made to reflect HW heterogeneity
that should be taken into account by SW.
Aim of this commit is to adapt values used by Zephyr to the same
diversity. This will help create new SoC values only when justified
by a real hardware difference that should be taken into account
by software.
For instance, for SoC stm32f103rb following define is used:
*STM32F103xB
Which means:
*Same SW could be used on STM32F103RB and STM32F103VB:
same CONFIG_SOC could be used
*Different SW should be used on STMF103RB and STM32F103R4:
different CONFIG_SOC should be used
This change focuses on stm32f1xx series.
Change-Id: I5ecfaa52952d04421b27b5e74fb71b4fc108b662
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Board uses nRF51822-QFAA, with 16kB of RAM and 256kB of flash.
Change-Id: I92b543022ae6103683cc9e16b925508fb3cf7db1
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Move common config options one level up to try to simplify the per-board
defconfig
Change-Id: I3d80fa494050634d0f877af2015b01b85df20d1d
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for the STM32F401 chip on the board
Change-Id: I96c0799f3658ecea096fa5971bce9faf21919ee1
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The BLE core on the Arduino 101 is an nRF51822 QFAA (256kB flash, 16kB
RAM).
Change-Id: Ia802b3eb634c0cd6775c4059c9569bccd915a578
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Removing options that are already set by the soc Kconfig files.
Change-Id: I603c7797a26e3afedfa5ee72fe989c614c080fe5
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Introduce an architecture sorting of boards. This is to allow for
easier maintenance going forward as the number of boards grows. It
will be easier for any scripts to know the board/arch mapping without
having to maintain an explicit list of what boards are associated with
which arch. We can also do things like have architecture maintainers
cover reviews and branches for arch/${ARCH} and boards/${ARCH} going
forward.
Change-Id: I02e0a30292b31fad58fb5dfab2682ad1c5a7d5a7
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
