Added changes required for nxp_enet ethernet driver to work
with multiple PHYs and fixed few problems:
- The cfg_link API resets PHY before configuring link. It was moved
here so the ethernet driver does not have to reset it - not all
PHYs need reset before configuring link and moving the reset code
here makes possible to have the reset done in a PHY specific way
(for example to reset by toggling GPIO pin). It also avoids ethernet
driver touching PHY registers without locking.
- When reset GPIO is not defined, reset is performed by setting reset
bit in control register.
- The cfg_link API does not return error when autonegotiation fails.
This fixes situation when the link is down at system start - ethernet
driver then skipped setting link-change callback and link was never
to be detected again.
- Added reset of excessive bits 16-31 when reading register values.
As only 16 bits are read from PHY, but the API is supposed to read
into uint32_t, the remaining bits contained previous data after
a successful read.
- Fixed missing mutex unlock when querying link state and link was down.
- Added missing initializer to link state variables. This could result
in link state change detection while link was still down, because
the speed/duplex settings could be random and old and new state
could be wrongly detected as different.
- Not logging link speed/duplex status when link is not up.
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
drivers: eth: phy: tja1103: Handle link change
These changes enable -
TJA1103 driver to gracefully handle Link connect or disconnect events
between Ethernet PHY and its link partner and notify it to the
upper network layers
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
- PHY can be set up as rmii but still use 25 MHz MDC, add DT property
value for this case
- Fix KSZ8081 driver spamming phy status in debug level logging,
and fix some other state/logging logic
- Fix PHY driver not rescheduling monitor work if first configuration
fails, change code path to use goto for errors
- Handle case where some phys are not using the gpio pins in phy driver
Make GPIO properties of ksz8081 phy optional since these hardware pins
may be unused on some boards
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
When there'is no phy at the address both registers will return
0xFFFF, giving a phy address of UINT32_MAX, not 0x00FFFFFF.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Add Driver for KSZ8081 Ethernet PHY. The Generic MII Driver
is not sufficient to use for this PHY chip which has special
vendor implemented behaviors.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Adds the tja1103 enet phy for setting phy options on the mr_canhubk3.
Co-authored-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Co-authored-by: Peter van der Perk <peter.vanderperk@nxp.com>
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
Decouples the generic MII PHY driver from the adin2111 driver by making
it depend on an ethernet-phy compatible devicetree node rather than the
adin2111 driver not being enabled. This makes it possible to add the
adin2111 driver to tests/drivers/build_all/ethernet
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Updates Ethernet PHY devicetree bindings to be more consistent with
Linux by using the standard `reg` property for the PHY address instead
of a custom `address` property. As a result, MDIO controller bindings
now require standard `#address-cells` and `#size-cells` properties.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Add `mdio_read_c45()`/`mdio_write_c45()` APIs for Clause 45 access
and remove the `protocol` MDIO binding property so that MDIO bus
controller can support more than one protocol.
A new MDIO header is introduced with generic opcodes, MMD and
registers addresses, to be used by MDIO and PHY drivers.
Existing MDIO drivers that support both Clause 22 and Clause 45
access are migrated to the new APIs.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Now that all in-tree phys are declared under their mdio bus, drop the
`mdio` property and use DT_INST_BUS to find the bus.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add support for ADIN1110 10BASE-T1L Ethernet MAC-PHY.
The ADIN1110 is an ultra low power, single port, 10BASE-T1L
transceiver design for industrial Ethernet applications and is com-
pliant with the IEEE® 802.3cg-2019™ Ethernet standard for long
reach, 10 Mbps single pair Ethernet (SPE). Featuring an integrated
media access control (MAC) interface, the ADIN1110 enables direct
connectivity with a variety of host controllers via a 4-wire serial
peripheral interface (SPI). This SPI enables the use of lower power
processors without an integrated MAC, which provides for the
lowest overall system level power consumption. The SPI can be
configured to use the Open Alliance SPI protocol or a generic SPI
protocol.
Documentation:
https://www.analog.com/en/products/adin1110.html
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Adds PHY driver. Works via MDIO API and
exposed ADIN2111 MDIO Clause 45
functions.
Link status detection is triggered by
ADIN2111 driver within offloaded IRQ
handler.
Supports:
- LED0, LED1 enable/disable
- Fatal HW error detection
- AN 2.4V tx mode enable/disable
The initialization order is important.
PHY 2 must be initialized after PHY1.
Therefore, it shall be defined after the 1st one
in the devicetree.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Advertise Gigabit Ethernet if the PHY supports it. As with the
other speeds, it is assumed the PHY supports both duplex modes.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Following zephyr's style guideline, all if statements, including single
line statements shall have braces.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Just use dev->name. This change follow same principles applied when
DEV_CFG and DEV_DATA macros were removed.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
A common pattern here was to take the work item as the subfield of a
containing object. But the contained field is not a k_work, it's a
k_work_delayable.
Things were working only because the work field was first, so the
pointers had the same value. Do things right and fix things to
produce correct code if/when that field ever moves within delayable.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Stop using redundant DEV_DATA/DEV_CFG macros and use dev->data and
dev->config instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Fixes: #38403
Adding NET_DRIVERS menuconfig so that network drivers are grouped
together in its own menu entry under drivers, similar to most other
drivers.
This further has the advantages that `CONFIG_NET_DRIVERS` can be used
for testing to determine if network drivers has been selected.
This changed revealed a dependency loop where both `select` (for SLIP)
and `depends` (for PPP) which both depends on NET_DRIVERS` where in use
in the dependency tree for Qemu networking, especially NET_SLIP_TAP.
This is handled by defaulting `NET_DRIVERS` to `y` when building for a
Qemu target.
`SLIP` had a dependency to `!QEMU_TARGET || NET_QEMU_SLIP`. This is
changed so that SLIP prompt depends on `!QEMU_TARGET` which provides
full user control in hardware but makes the symbol promptless on Qemu
targets.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
This commit adds support for Ethernet PHY drivers via a PHY API.
It also includes a driver for a generic MII compliant PHY
which supports most PHYs on the market.
Separating PHY driver from the SoC specific Ethernet driver
simplifies the Ethernet driver code and enables code re-use.
Drivers for specific PHYs with more advanced features, such as
RGMII delay in PHY can be developed independent of the Ethernet
MAC driver.
Signed-off-by: Arvin Farahmand <arvinf@ip-logix.com>
