Adds a DAC driver for Texas Instruments DACx0501 family of devices
Signed-off-by: Eran Gal <erang@google.com>
Co-authored-by: Martin Jäger <17674105+martinjaeger@users.noreply.github.com>
Rename ad5592 files in dts, driver and include to ad559x and add support
for I2C bus which is required for AD5593.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Do not enable subsystem/driver shell modules by default and stop abusing
CONFIG_SHELL_MINIMAL, which is internal to the shell subsystem, to decide
when to enable a driver shell.
The list of shell modules has grown considerably through the
years. Enabling CONFIG_SHELL for doing e.g. an interactive debug session
leads to a large number of shell modules also being enabled unless
explicitly disabled, which again leads to non-negligible increases in
RAM/ROM usage.
This commit attempts to establish a policy of subsystem/driver shell
modules being disabled by default, requiring the user/application to
explicitly enable only those needed.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
LTC1665/LTC1660 is a 8/10-bit Digital-to-Analog Converter
(DAC) with eight individual channels.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Unify the drivers/*/Kconfig menuconfig title strings to the format
"<class> [(acronym)] [bus] drivers".
Including both the full name of the driver class and an acronym makes
menuconfig more user friendly as some of the acronyms are less well-known
than others. It also improves Kconfig search, both via menuconfig and via
the generated Kconfig documentation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
MCP4728 is a 12-bit, Quad Digital-to-Analog Converter with EEPROM Memory.
Controlled via I2C interface.
Signed-off-by: Marek Janus <marek.janus@grinn-global.com>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Refactors all of the DAC drivers to use a shared driver class
initialization priority configuration, CONFIG_DAC_INIT_PRIORITY, to
allow configuring DAC drivers separately from other devices. This is
similar to other driver classes like I2C and SPI.
The default is set to CONFIG_KERNEL_INIT_PRIORITY_DEVICE to preserve the
existing default initialization priority for most drivers. The
exceptions are dacx0508, dacx3608, and mcp4725 drivers which have
dependencies on SPI or I2C drivers and must therefore initialize later
than the default device priority.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Add Digital-to-Analog Converter driver (based on DACC module) for Atmel
SAM MCU family. Only SAME70, SAMV71 series devices are supported in
this version.
Tested on Atmel SMART SAM E70 Xplained board.
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The DAC53608 and DAC43608 (DACx3608) are lowpower, eight-channel,
voltage-output, 10-bit or 8-bit digital-to-analog converters (DACs)
respectively. They support I2C with a wide power supply range
from 1.8 V to 5.5 V, and a full scale output voltage range of
1.8 V to 5.5 V. The DACx3608 also includes per channel, user
programmable, power down registers.
Signed-off-by: Matija Tudan <mtudan@mobilisis.hr>
If shell is enabled then enable all sub-shells if their dependencies are
satisfied. This was done for some modules and subsystems but was not
consistent.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
DAC (digital to analog converter) peripheral driver with a generic API
suitable for most MCUs (only basic DAC features considered).
Signed-off-by: Martin Jäger <martin@libre.solar>
