In this board, there are eight PWM channels from
EMIOS 0 CH0 --> EMIOS 0 CH7 that can be used to
generate PWM pulse to outside of the board.
Moreover, there are three RGB leds that can use
PWM pins for blinking, faded leds
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Update TF-M version with fix for build with shared boot data enabled,
i.e. CONFIG_TFM_MCUBOOT_DATA_SHARING=y.
Regression from: 485fa940aa
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
* In Zephyr: The HW models now include N interrupt controllers
The interrupt handling code needs to target one controller
specifically.
* Update the HW models module to
57b61a9a2da75c860f15ca79522b24d57992df2c
Including the following:
* 57b61a9 INT CNTRL: Generalize to N controllers
* 1ea8194 nrf_bsim_redef.h: Add first definitions for nrf5340
* 5f81ee9 irq_ctrl: Lower a bit HW event priority
* 0986acc RNG: Add nrf53 variant in model
* 09345da RNG: Generate level interrupts instead of pulse ones
* f9b7c7a DPPI: Add first version
* 62dabd3 HW models: Initial peripheral adaptation for multi-int_cntr
* f54b59d HW models: Adding initial nrf5340 structure
* fb1edd9 HW models: Use HW types definitions only where neded
* 2744f4c Add basic support for variants
* a5f79cd nrf_bsim_redef.h: Remove unnecessary redefinitions
* 2c781dd HW_models: Improve includes
* bdb0a08 minor: Remove non-ASCII characters from source
* b5e95bd RADIO: Corrected note about MAXLEN and CRCINC behaviour
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Update SNVS pin names in RT11xx DTSI files to align with new pin data
generated for the RT1176 and RT1166 processors. This pin data is stored
within the NXP HAL, so the SHA of the HAL is also updated by this
commit.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
- fix i2c hang issue
- switch hpet/i2c/uart/gpio to use osxml generated header files for
IP registers
- spi dma support
Signed-off-by: Dong Wang <dong.d.wang@intel.com>
Update Zephyr fork of MCUboot to revision:
11ecbf639d826c084973beed709a63d51d9b684e
Brings following Zephyr relevant changes and fixes:
- 11ecbf63 zephyr: use cmsis_core.h header
- da65db00 zephyr: Provide slot definitions for three images
- 2c61caf6 bootutil: Move flash_area_id_to_image under ifdef
- 904d0c46 bootutil: Add DirectXIP version of boot_set_next
- 2a874b6e zephyr: Do not build in debug mode
- 258a6c7d bootutil: Fix support for more than 2 flash areas
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The Xtensa HAL has been updated with the following changes:
* Removed intel_s1000 overlay files as it is no longer needed.
* Fix uninitialized variable warning in xthal_v2p()
* Add config and overlay files for dc233c core so we can use
QEMU with this core to test MMU code.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert the nrf52_bsim board, to use the native simulator
as its engine.
This means some of the functionality the board included
before is now handled by the native simulator, including
the overall program main and CPU/HW scheduling.
Note that this board remains separate from the native_sim
board, even if both use the native simulator.
Also update the nRF HW models component to a new version
which has been converted into an extension for the
native simulator.
After this change, it becames also possible to build
the nrf52_bsim with an embedded C library, and to
use with it the Zephyr POSIX API shim.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The CMSIS module glue code was part of arch/ directory. Move it to
modules/cmsis, and provide a single entry point for it: cmsis_core.h.
This entry header will include the right CMSIS header (M or A/R).
To make this change possible, CMSIS module Kconfig/CMake are declared as
external, allowing us to add a new Zephyr include directory.
All files including CMSIS have been updated.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The nRF HW models have been updated to include the following
fixes and improvements:
* RADIO: Handle MAXLEN and other related improvements
* PPI: Added 2 notes about status and shortcommings
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Align all sensor drivers that are using stmemsc (STdC) HAL i/f
to new APIs of stmemsc v2.3
Requires https://github.com/zephyrproject-rtos/hal_st/pull/16
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The existing heap starts at the beginning of SPIRAM which is also occupied
by the WiFi stack if CONFIG_ESP32_WIFI_NET_ALLOC_SPIRAM is enabled. This
results in memory corruption.
Update the linker description to add a _spiram_heap_start symbol and add a
KConfig size option to allow the SPIRAM stack to be correctly located and
sized. Requires matching commit in hal_espressif.
Fixes: 61359
Signed-off-by: Eric Holmberg <eric.holmberg@northriversystems.co.nz>
This enables the power management for Intel ISH. It supports D0i1,
D0i2, D0i3 power saving modes for ISH.
Signed-off-by: Leifu Zhao <leifu.zhao@intel.com>
The change is to update the location of the NXP HAL license file (BSD-3)
to the root of the NXP HAL repo.
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
Implement the sys_poweroff hook for all ESP32 SoCs based on the previous
SOFT_OFF implementation.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The nRF HW models have been updated to include the following
fixes and improvements:
* TIMER: Fix bogus events/interrupts if shorts where used
* PPI: Handle well an event triggering a task twice
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Update trusted-firmware-m to 1.8.0, mbedtls to 3.4.0, and tf-m-tests to
1.8.0. Includes minor cmake changes due to file renames and such, as well
as adjusting the return type of a callback function that has changed since
the previous version of trusted-firmware-m.
Signed-off-by: David Brown <david.brown@linaro.org>
SiLabs' sleeptimer driver supports several hardware peripherals, of
which the counter driver so far only supports the RTCC-based variant.
This patch adds support for the SYSRTC-based sleeptimer implementation,
which is required for Gecko SoCs that do not have an RTCC module.
Signed-off-by: Markus Fuchs <markus.fuchs@ch.sauter-bc.com>
The Zephyr-specific Segger SystemView configuration was not used as
the same file was available inside the external Segger module with
higher import priority.
Fixes the regression by moving the SystemView configuration to the same
place in the external module where RTT configuration already resides and
thereby creates a canonical include path to avoid further regressions of
the same kind.
Fixes: #61133
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
This version introduces support for the syscalls extension,
which greatly reduces the amount of bandwidth being used
for tracing syscalls.
Signed-off-by: Aron Lander <aron.lander@percepio.se>
Add initial support for NXP S32 GMAC/EMAC:
- it's a copy-implementation with DMA data buffers and buffer
descriptors in non-cached memory (buf len and ring size configurable)
- PHY interface selection only implemented for S32K3 devices as it is
SoC-specific
- no PHY driver integration, it works as a fixed link with speed/duplex
configured through devicetree
- supports multicast hash filtering, promiscuous mode, MAC loopback
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The nRF HW models have been updated to include the following
fixes and improvements:
* TIMER: Add missing HAL function override
* TIMER: Added notes about minor differences
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The nRF HW models have been updated to include the following
fixes and improvements:
* RADIO: Bugfix if DISABLE or STOP during first us of TxStart
* File opening: Create folders if missing
* TIMER: Completed, including all count functionality
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Update uoscore-uedhoc repository to the latest revision.
Align uoscore tests with the API changes.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This adds basic support for 'B' revision of the Silicon Labs EFR32BG
BRD4184 (Thunderboard BG22) board. Due to missing drivers, some of the
on-board peripherals are currently unsupported:
- Silicon Labs Si7021 relative humidity and temperature sensor
- Vishay VEML6035 ambient light sensor
- Knowles SPK0641HT4H-1 MEMS microphones
- TDK InvenSense ICM-20648 6-axis inertial sensor
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Enable all channels that available connector on board.
ADC0 channel 6 on precision group with normal end chain
callback.
ADC1 channel 2 on precision group with normal end of
conversion callback.
ADC2 channels 3, 4, 5 on precision group with normal end
of conversion callback.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Reuse existing MCUX-based shim driver for FlexCAN.
Enable flexcan0 for Zephyr canbus to run tests.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
When `nrfx_pwm_stopped_check()` was called multiple times it was
returning incorrect value after second and next calls.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
The nRF HW models have been updated to include the following
fixes and improvements.
* RADIO: Improve T_IFS support, and fix for low latency mode
* docs: Miscelaneous improvements
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
