Add a note about the new K_MEM_POOL_HEAP_SIZE define and the mechanism
for specifying custom system heap size requirements.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add an entry to indicate the changes to the coap_service_send and
coap_resource_send API functions.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Why?
- metadata is easier to manage as an array + index
- less error-prone -> less memory-management bugs
- we can. because of the previous refactor
- PDU allocations are more predictable
- ATT buffer size can be optimized by app
- isolates ATT from the rest of the ACL users
- decouples ATT PDU size from e.g. SMP w/ LESC
Drawbacks:
- higher memory usage
- kconfig change
The higher memory use is only temporary, as this will be followed-up
with more refactors that should bring it back down.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
Co-authored-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
Replace function parameter 'retries' with pointer to structure
holding coap transmission parameters. This allows setting the
retransmission parameters individually for each pending request.
Add coap transmission parameters to coap_pending structure.
Update migration guide and release notes.
Signed-off-by: Juha Ylinen <juha.ylinen@nordicsemi.no>
Renames "prov device" references and options to
"provisionee" to align implementation with Mesh
Protocol specification v1.1, section 5.4.
Signed-off-by: Anders Storrø <anders.storro@nordicsemi.no>
There is no in-tree user. Also, it is misleading as we use
SCOMPARE1 for spinlock too, not just IPC.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC should be defined at the SoC
or the board level since Xtensa cores are high configurable.
The default is just for ISS (Instruction Set Simulator). So
remove it from the arch level.
The xt-sim board is the only one in tree that is targeting
the ISS, so add it there.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Rename the native Linux SocketCAN driver to reflect that it can can now be
used in both native_posix and native_sim (with or without an embedded
C-library).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Update migration guide to introduce the stm32_lp_tick_source
for stm32 device when choosing the LPTIM fo lowPower modes.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Commit adds implementation of the specification
recommendations regarding randomization of
responses on the access layer.
3.7.3.1 Transmitting an Access messages
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Adds a note that the shell mcuboot erase command can no
longer erase the MCUboot or application slots
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Update the release notes and migration guide for CoAP events using
the Network Events subsystem.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Add information about the IPv4 multicast IP_ADD_MEMBERSHIP and
IP_DROP_MEMBERSHIP socket options.
Add information about the IPv6 multicast IPV6_ADD_MEMBERSHIP and
IPV6_DROP_MEMBERSHIP socket options.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add information about IPv4 TTL and IPv6 hoplimit changes
for unicast and multicast packets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add information about IPv4 TTL and IPv6 hoplimit changes
for unicast and multicast packets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
native_sim is superceeding native_posix.
Let's recommend users to use it instead.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
These were first deprecated in v3.2. We have kept support for them
for as long as we can, but now their presence is causing CI failures
in some configurations. Specifically, using the deprecated 'label'
property is causing a warning which is promoted to an error in some
twister runs. This is blocking other forward progress in the
devicetree API.
I tried to rework the tests to avoid this, but it was too much effort
for the time I had to work on the task. Removing the APIs is therefore
unfortunately the best way forward to unblocking other work.
Re-work the test suite a bit to maintain coverage where we are using
the label property to test other macros.
Add a migration guide section to help with the transition.
Signed-off-by: Martí Bolívar <mbolivar@amperecomputing.com>
Note that native_sim is replacing native_posix as default
test platform.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This allows HCI drivers to expose vendor-specific functions to set the
public address.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
Add a name for the Kconfig choice symbol
indicating the Zbus subscriber buffer allocation
and adjust the name of the existing choices.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
Added note about the migration steps needed to support the new IGMP api.
The api now expects an additional argument used for joining an IGMPv3
group.
Signed-off-by: Ibe Van de Veire <ibe.vandeveire@basalte.be>
The Bluetooth Mesh ``element`` declaration has been changed to add
prefix ``const``. The ``elem->addr``field has been changed to the
new runtime structure, replaced by ``elem->rt->addr``.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
Statically initialise the callback list so that subscriptions can be
registered before the call to `bt_enable`.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Rename the lorawan_set_battery_level_callback to
lorawan_register_battery_level_callback to make it consistent with other
functions for downlink and data rate changed callbacks.
Also making the function void for consistency. The get_battery_level
already checks if the callback is NULL before invoking it.
Signed-off-by: Martin Jäger <martin@libre.solar>
Add a note to the 3.6 migration guide about the CoAP API changes
introduced with the CoAP server subsystem.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Adds a note about how to replicate the functionality of the now
removed MCUboot mass erase Kconfig option
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Add in DT the possibility to configure both INT1 and INT2
pin. The driver will then assign one of the two (either 1
or 2, according to what value drdy_pin is set) to a gpio
for receiving drdy interrupts.
The other pin may be used in the future to receive event
interrupts.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
