Add LEDC device for esp32s3
Update PWM LED binding
Remove invalid comment from driver source file
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Support for the measuring the CPU die temperature
for the ESP32 targets S2,C3. The ESP32 support
was ommited due to lack of offset calibration.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
This reverts commit fdd47f39be.
After v4.4.1, write-block-size is no longer needed to be 32-bytes
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
- adds properties 'group', 'index' and 'prescaler'.
- updates board's dts to include those properties.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
This commit moves the hardware configuration for ledc
peripheral to the device-tree instead of Kconfig.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Current write block size does not guarantee proper
write operation, what might cause corrupted data.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
On Espressif SoCs, the pin controller is a virtual device.
Pin settings are actually controlled in a distributed way.
Therefore, that node does not belong to the SoC bus.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
In order to bring consistency in-tree, migrate all dts code to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to zephyrproject-rtos#45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add a GPIO pass-thru map for accessing the full range (0 to 39) of ESP32
GPIO pins by their datasheet number.
GPIOs 0 to 31 are mapped to gpio0 while GPIOs 32 to 39 are mapped to
gpio1.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
The pinctrl support made usage of the 'peripheral'
property no longer required.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Current uart driver implementation is incompleted regarding the
usage of DT_INST_FOREACH_STATUS_OKAY. If uart0 and uart2 are selected,
build breaks due to peripheral number ordering, which would be
0 and 1 in this case. This fix PR fix this by re-working the macros
and setting proper uart peripheral instances in DTSI, required for signal
routing configuration.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
By enabling SMP option plus the APPCPU, also
completes the SMP port by adding the esp32
specific arch_sched_ipi() function
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
Not all boards use the same UART's defaults properties.
This commit updates device tree declarations by deferring
specific definitions to the board's DTS.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
add ledc to board dtsi file,
change compatible and device define in pwm driver,
add yaml for board ledc support,
fix missing include for board in gpio include
Signed-off-by: Andrei-Edward Popa <andrei_edward.popa@upb.ro>
Use i2c_hal functions to enable support for
multiple SoCs.
Use DT compat to enable I2C from device
tree configuration
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
This joins all clock control handling to same source
by using hal clock functions. It also brings ESP32C3
clock support.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
1) Allow use of interrup driven instance.
ROM implementation could be selected via dts compatiable.
2) Use UART rx fifo and timeout interrupt for end of message detection.
Added to decrease interrupts count on data reception
3) Use ESP_LL api.
Signed-off-by: Pavlo Hamov <p.hamov@venstar.com>
