Convert driver to use DT_INST_ defines.
In the process, we've removed all UART/USART/LPUART code in
device instanciation code which had no impact.
Since all uart/usart/lpuart nodes declare compatibility with
st,stm32uart, DT_INST_X_ST_STM32_UART_FOO could be used.
Removed DT_UART fixup macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
When building with LLVM we get the following error:
uart_stm32.c:272:9: error: implicit conversion from enumeration type
'enum uart_config_parity' to different enumeration type
'enum uart_config_flow_control' [-Werror,-Wenum-conversion]
return UART_CFG_PARITY_NONE;
~~~~~~ ^~~~~~~~~~~~~~~~~~~~
We shouldn't be mixing parity and flow control enum's. Use
UART_CFG_FLOW_CTRL_NONE instead or UART_CFG_PARITY_NONE.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This patch tests the return code when calling clock_control_get_rate
and completes the issue #20503 seen on watchdog
[Coverity CID :205655]
Fixes#20503
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Currently both uart_stm32_irq_tx_complete() and
uart_stm32_irq_tx_ready() return the TXE flag. However
uart_irq_tx_complete() should really return the TC flag to output true
"Transmit Complete" status.
Signed-off-by: Tommy Vestermark <tovsurf@vestermark.dk>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move uart.h to drivers/uart.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move clock_control.h to drivers/clock_control.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Per guidelines, all statements should have braces around them. We do not
have a CI check for this, so a few went in unnoticed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
On STM32 series currently available in Zephyr,
LPUART and U(S)ART IPs are similar and share most of their
registers. As a consequence LL API defined for U(S)ART also
applies to LPUART.
This allows to remove specific LPUART code.
Restrict use of LL LPUART API when it diverges from UART one.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Allows to enable initial RTS/CTS hardware flow control
in the dts.
Co-authored-by: Benoit Leforestier <benoit.leforestier@gmail.com>
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
In case of TX IRQ pending,
uart_stm32_irq_is_pending() function always return 0,
because "is TXE enabled ?" is checked instead of "is TC enabled ?".
Signed-off-by: Benoit Leforestier <benoit.leforestier@gmail.com>
Following recent renaming of STM32 UART Kconfig UART symbols,
LPUART was named as UART_LPUART_1.
Rename to LPUART_1.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32 uart Kconfig instance flags were not following
same naming scheme than other drivers (i2c, spi, ..)
Update driver to use UART_X instead of UART_STM32_PORT_X
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Check clock_control_on return value now that it is checking appropriate
bus is used in the request.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
poll_out function was returning the character that was sent. It
happens that it is always constant and the return of this functions is
never tested. Changing it to be a void function.
MISRA-C rule 17.7
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Provide CONFIG macros for clocks bits and bus properties in fixup
files and use them to simplify logic in uart devices instanciation
code
Fixes#10448
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
If data is received before an IRQ handler was set and enabled,
hardware sets the ORE flag. Once set, the IRQ routine starts
hogging the CPU until ORE is cleared. This change will clear
the flag when user code attempts to drain incoming data.
Signed-off-by: Kiril Zyapkov <k.zyapkov@allterco.com>
Zephyr UART drivers offer very low-level functionality. Oftentimes,
it would be useful to provide higher-level wrappers around UART
device which would offer additional functionality. However, UART
driver irq callback routine receives just a pointer to (low-level)
UART device, and it's not possible to get to a wrapper structure
(without introducing expensive external mapping structures). This
is an indirect reason why the current UARt wrappers - uart_pipe,
console - are instantiated statically just for one underlying UART
device and cannot be reused for multiple devices.
Solve this by allowing to pass an arbitrary user data to irq
callback, set by new uart_irq_callback_user_data_set() function.
Existing uart_irq_callback_set() keeps setting a callback which
will receive pointer to the device.
While public API maintains compatibility, drivers themselves need
to be updated to support arbitrary user data storage/passing (as
legacy uart_irq_callback_set() functionality is now implemented in
terms of it).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
clear RXNE flag in fifo_read, remove TEACK and REACK
check when uart_stm32_init because stm32f2 doesn't
has those flags.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
In order to ease integration of new series, remove reference to
series in code activation. Use LPUART support Kconfig symbol instead.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Remove reference to SoC series in activation of TEACK/REACK flags
checks. Use flags definitions instead which is defined, if supported,
in STM32Cube packages.
Decouple the checks since REACK is not supported in some series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
LPUART (Low-power UART) peripheral is just like ordinary U(S)ART
which lives in a separate clock/power domain.
Therefore already existing code could be reused as is
almost entirely.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
LBD interrupt manupulation makes sense for UART with LIN support only.
Otherwise this bit should not be touched.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
STM32Lx LPUART peripherals do not fit well into existing U(S)ART
port numbering scheme, so there will be two separate namespaces
in Kconfig: one for U(S)ARTs and one for LPUARTs.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Replace specific STM32F1 references with generic STM32 ones.
Use generic names like U(S)ARTx for instances which have different
naming across STM32 families.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Some mcu's have USART_PRESC_PRESCALER defined in the function call. Add
a prescaler of div1 to it.
Signed-off-by: Pushpal Sidhu <psidhu.devel@gmail.com>
STM32 UART driver uses a macro for clock initialization, that
is difficult to read and incompatible with needed changes to
fix STM32F0 series UART problems.
This change switches to using the full clock bus names in UART
init functions removing the macro-magic and increasing
readability.
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
Fix#5298
irq_is_pending function returned TXE/RXNE flag status
even if IRQ was masked, which led to enless loop
in uart_pipe when no TX was performed. Fix by reporting status only when
IRQ is unmasked.
Signed-Off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32 UART driver was using a mix of LL/HAL APIs. This commit removes
calls to HAL API and replaces them with LL APIs. No functional change
have been seen during non regression testing.
But we could note a direct gain of 1Kb of ROM
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
