/* * Copyright (c) 2020 TriaGnoSys GmbH * * SPDX-License-Identifier: Apache-2.0 */ /dts-v1/; #include #include #include / { model = "Silicon Labs BRD2601B (Mighty Gecko Radio Board)"; compatible = "silabs,efr32mg24_brd2601b", "silabs,efr32mg24"; chosen { zephyr,console = &usart0; zephyr,shell-uart = &usart0; zephyr,sram = &sram0; zephyr,flash = &flash0; zephyr,code-partition = &slot0_partition; }; aliases { led0 = &red_led; led1 = &green_led; led2 = &blue_led; sw0 = &button0; sw1 = &button1; }; leds { compatible = "gpio-leds"; red_led: led_2 { gpios = <&gpiod GECKO_PIN(2) GPIO_ACTIVE_LOW>; }; green_led: led_0 { gpios = <&gpioa GECKO_PIN(4) GPIO_ACTIVE_LOW>; }; blue_led: led_1 { gpios = <&gpiob GECKO_PIN(0) GPIO_ACTIVE_LOW>; }; }; buttons { compatible = "gpio-keys"; button0: button_0 { gpios = <&gpiob GECKO_PIN(2) GPIO_ACTIVE_LOW>; zephyr,code = ; }; button1: button_1 { gpios = <&gpiob GECKO_PIN(3) GPIO_ACTIVE_LOW>; zephyr,code = ; }; }; wake_up_trigger: gpio-wake-up { compatible = "silabs,gecko-wake-up-trigger"; gpios = <&gpioa GECKO_PIN(5) GPIO_ACTIVE_LOW>; }; sensor_enable: gpio_switch_0 { compatible = "regulator-fixed"; regulator-name = "sensor_enable"; enable-gpios = <&gpioc GECKO_PIN(9) GPIO_ACTIVE_HIGH>; regulator-boot-on; }; }; &cpu0 { clock-frequency = <78000000>; }; &usart0 { current-speed = <115200>; pinctrl-0 = <&usart0_default>; pinctrl-names = "default"; status = "okay"; }; &i2c0 { pinctrl-0 = <&i2c0_default>; pinctrl-names = "default"; status = "okay"; veml6035: veml6035@29 { compatible = "vishay,veml7700"; reg = <0x29>; status = "okay"; }; si7210: si7210@30 { compatible = "silabs,si7210"; reg = <0x30>; status = "okay"; }; si7021: si7021@40 { compatible = "silabs,si7006"; reg = <0x40>; status = "okay"; }; }; &gpio { status = "okay"; }; &gpioa { status = "okay"; }; &gpiob { status = "okay"; }; &gpioc { status = "okay"; }; &gpiod { status = "okay"; }; &wdog0 { status = "okay"; }; &se { status = "okay"; }; &flash0 { partitions { compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; /* Reserve 48 kB for the bootloader */ boot_partition: partition@0 { label = "mcuboot"; reg = <0x0 0x0000c000>; read-only; }; /* Reserve 464 kB for the application in slot 0 */ slot0_partition: partition@c000 { label = "storage"; reg = <0x0000c000 0x00074000>; }; /* Reserve 464 kB for the application in slot 1 */ slot1_partition: partition@80000 { label = "image-0"; reg = <0x00080000 0x00074000>; }; /* Reserve 32 kB for the scratch partition */ scratch_partition: partition@f4000 { label = "image-1"; reg = <0x000f4000 0x00008000>; }; /* Set 528Kb of storage at the end of the 1024Kb of flash */ storage_partition: partition@fc000 { label = "image-scratch"; reg = <0x000fc000 0x00084000>; }; }; }; &adc0 { status = "okay"; };