c80ace50f4
For more effective code execution on STM32 devices is convenient to enable flash prefetch buffer. To be enabled by default, possible to disable using kconfig. Signed-off-by: Lubos Koudelka <lubos.koudelka@st.com>
96 lines
2.6 KiB
Plaintext
96 lines
2.6 KiB
Plaintext
# Copyright (c) 2024 STMicroelectronics
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
|
|
config SOC_FAMILY_STM32
|
|
select HAS_SEGGER_RTT if ZEPHYR_SEGGER_MODULE
|
|
select STM32_ENABLE_DEBUG_SLEEP_STOP if DEBUG || ZTEST
|
|
select BUILD_OUTPUT_HEX
|
|
|
|
if SOC_FAMILY_STM32
|
|
|
|
rsource "*/Kconfig"
|
|
|
|
# STM32 wide symbols definitions
|
|
|
|
# Workaround for not being able to have commas in macro arguments
|
|
DT_CHOSEN_Z_CCM := zephyr,ccm
|
|
|
|
config STM32_CCM
|
|
def_bool $(dt_chosen_enabled,$(DT_CHOSEN_Z_CCM))
|
|
|
|
config USE_STM32_ASSERT
|
|
depends on ASSERT
|
|
bool "STM32Cube HAL and LL drivers asserts"
|
|
help
|
|
Enable asserts in STM32Cube HAL and LL drivers.
|
|
|
|
config STM32_BACKUP_SRAM
|
|
bool "STM32 Backup SRAM"
|
|
depends on DT_HAS_ST_STM32_BACKUP_SRAM_ENABLED
|
|
help
|
|
Enable support for STM32 backup SRAM.
|
|
|
|
config STM32_ENABLE_DEBUG_SLEEP_STOP
|
|
bool "Allow debugger attach in stop/sleep Mode"
|
|
help
|
|
Some STM32 parts disable the DBGMCU in sleep/stop modes because
|
|
of power consumption. As a side-effects this prevents
|
|
debuggers from attaching w/o resetting the target. This
|
|
effectivly destroys the use-case of `west attach`. Also
|
|
SEGGER RTT and similar technologies need this.
|
|
|
|
config SWJ_ANALOG_PRIORITY
|
|
int "SWJ DP port to analog routine initialization priority"
|
|
default 49
|
|
help
|
|
Initialization priority of the routine within the PRE_KERNEL1 level.
|
|
This priority must be greater than GPIO_INIT_PRIORITY and lower than
|
|
UART_INIT_PRIORITY.
|
|
|
|
config STM32_FLASH_PREFETCH
|
|
bool "Flash prefetch buffer"
|
|
|
|
choice POWER_SUPPLY_CHOICE
|
|
prompt "STM32 power supply configuration"
|
|
default POWER_SUPPLY_LDO
|
|
depends on SOC_SERIES_STM32H7X || SOC_SERIES_STM32U5X || \
|
|
SOC_STM32WBA55XX
|
|
|
|
config POWER_SUPPLY_LDO
|
|
bool "LDO supply"
|
|
|
|
config POWER_SUPPLY_DIRECT_SMPS
|
|
bool "Direct SMPS supply"
|
|
|
|
config POWER_SUPPLY_SMPS_1V8_SUPPLIES_LDO
|
|
bool "SMPS 1.8V supplies LDO (no external supply)"
|
|
depends on SOC_SERIES_STM32H7X
|
|
|
|
config POWER_SUPPLY_SMPS_2V5_SUPPLIES_LDO
|
|
bool "SMPS 2.5V supplies LDO (no external supply)"
|
|
depends on SOC_SERIES_STM32H7X
|
|
|
|
config POWER_SUPPLY_SMPS_1V8_SUPPLIES_EXT_AND_LDO
|
|
bool "External SMPS 1.8V supply, supplies LDO"
|
|
depends on SOC_SERIES_STM32H7X
|
|
|
|
config POWER_SUPPLY_SMPS_2V5_SUPPLIES_EXT_AND_LDO
|
|
bool "External SMPS 2.5V supply, supplies LDO"
|
|
depends on SOC_SERIES_STM32H7X
|
|
|
|
config POWER_SUPPLY_SMPS_1V8_SUPPLIES_EXT
|
|
bool "External SMPS 1.8V supply and bypass"
|
|
depends on SOC_SERIES_STM32H7X
|
|
|
|
config POWER_SUPPLY_SMPS_2V5_SUPPLIES_EXT
|
|
bool "External SMPS 2.5V supply and bypass"
|
|
depends on SOC_SERIES_STM32H7X
|
|
|
|
config POWER_SUPPLY_EXTERNAL_SOURCE
|
|
bool "Bypass"
|
|
depends on SOC_SERIES_STM32H7X
|
|
|
|
endchoice
|
|
|
|
endif # SOC_FAMILY_STM32
|