patrick/zephyr
1
0
Fork 0
Code Issues Pull requests Actions 7 Packages Projects Releases Wiki Activity
zephyr/boards/nxp/twr_ke18f/Kconfig

14 lines
304 B
Plaintext
Raw Permalink Normal View History

kconfig: Clean up header comments and make them consistent Use this short header style in all Kconfig files: # <description> # <copyright> # <license> ... Also change all <description>s from # Kconfig[.extension] - Foo-related options to just # Foo-related options It's clear enough that it's about Kconfig. The <description> cleanup was done with this command, along with some manual cleanup (big letter at the start, etc.) git ls-files '*Kconfig*' | \ xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /' Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-11-01 13:45:29 +01:00
# TWR-KE18F board configuration
boards: twr-ke18f: add support for the NXP TWR-KE18F board Add support for the NXP TWR-KE18F development board. This board feautures an NXP MKE18F16 MCU, a selection of user LEDs and push-buttons, potentiometer, thermistor, CAN interface, and FlexIO header. Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
2019-05-07 20:24:03 +02:00
# Copyright (c) 2019 Vestas Wind Systems A/S
# SPDX-License-Identifier: Apache-2.0
if BOARD_TWR_KE18F
config BOARD_TWR_KE18F_FLEXIO_CLKOUT
kconfig: remove Enable from boolean prompts According to Kconfig guidelines, boolean prompts must not start with "Enable...". The following command has been used to automate the changes in this patch: sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig* Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
2022-03-09 12:05:12 +01:00
bool "CLKOUT signal on FlexIO header"
boards: twr-ke18f: add support for the NXP TWR-KE18F board Add support for the NXP TWR-KE18F development board. This board feautures an NXP MKE18F16 MCU, a selection of user LEDs and push-buttons, potentiometer, thermistor, CAN interface, and FlexIO header. Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
2019-05-07 20:24:03 +02:00
help
Enable the CLKOUT signal on FlexIO header pin 7 (PTE10).
kconfig: Global whitespace/consistency cleanup Clean up space errors and use a consistent style throughout the Kconfig files. This makes reading the Kconfig files more distraction-free, helps with grepping, and encourages the same style getting copied around everywhere (meaning another pass hopefully won't be needed). Go for the most common style: - Indent properties with a single tab, including for choices. Properties on choices work exactly the same syntactically as properties on symbols, so not sure how the no-indentation thing happened. - Indent help texts with a tab followed by two spaces - Put a space between 'config' and the symbol name, not a tab. This also helps when grepping for definitions. - Do '# A comment' instead of '#A comment' I tweaked Kconfiglib a bit to find most of the stuff. Some help texts were reflowed to 79 columns with 'gq' in Vim as well, though not all, because I was afraid I'd accidentally mess up formatting. Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-11-01 10:24:07 +01:00
endif # BOARD_TWR_KE18F
Reference in a new issue Copy permalink