OT does not have 64 bit timestamp support. This is a limitation of OT
and not of the IEEE 802.15.4 driver API. Therefore any workaround
related to such OT idiosyncracies should be encapsulated inside the OT
adapatation layer.
This change moves the OT-specific conversion of OT 32 bit timestamps to
Zephyr 64 bit timestamps into the OT adaptation layer.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
The IEEE 802.15.4 API and networking subsystem were using several
inconsistent timestamp resolutions and types. This change defines all
timestamps with nanosecond resolution and reduces the number of
available types to represent timestamps to two:
* `struct net_ptp_time` for PTP timestamps
* `net_time_t` for all other high resolution timestamps
All timestamps (including PTP timestamps) are now referred to a
"virtual" local network subsystem clock source based on the well-defined
types above. It is the responsibility of network subsystem L2/driver
implementations (notably Ethernet and IEEE 802.15.4 L2 stacks) to ensure
consistency of all timestamps and radio timer values exposed by the
driver API to such a network subsystem uptime reference clock
independent of internal implementation details.
The "virtual" network clock source may be implemented based on arbitrary
hardware peripherals (e.g. a coarse low power RTC counter during sleep
time plus a high resolution/high precision radio timer while receiving
or sending). Such implementation details must be hidden from API
clients, as if the driver used a single high resolution clock source
instead.
For IEEE 802.15.4, whenever timestamps refer to packet send or receive
times, they are measured when the end of the IEEE 802.15.4 SFD (message
timestamp point) is present at the local antenna (reference plane).
Due to its limited range of ~290 years, net_time_t timestamps (and
therefore net_pkt timestamps and times) must not be used to represent
absolute points in time referred to an external epoch independent of
system uptime (e.g. UTC, TAI, PTP, NTP, ...).
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Adapts a return type to the API specification. The changed return type
is not referenced anywhere so it can be changed without breaking
backwards compatibility.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
The support for capability IEEE802154_OPENTHREAD_HW_MULTIPLE_CCA is added
to the ieee802154_nrf5 driver.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
Use generic symbols defined in ieee802154.h for packet/FCS size instead
of redefining them in the driver header.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
In case upper layer does not follow the convention, and the net_pkt
provided to the nRF 15.4 driver had a payload larger than the maximum
payload size of an individual 15.4 frame, the driver would end up with
buffer overflow.
Fix this by adding an extra payload_len check before attempting to copy
the payload to the internal buffer.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The Kconfig IEEE802154_NRF5_MULTIPLE_CCA option is added.
The new functions `z_ieee802154_nrf5_extra_cca_attempts_set` and
`z_ieee802154_nrf5_extra_cca_attempts_get` are added.
The ieee802154_nrf5.c is updated allowing to pass extra cca attempts
to nRF 802.15.4 Radio Driver.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
The code declares variables in switch-case blocks. This
seems to compile without an error on GCC 11 and newer,
but older compilers don't accept this code.
Signed-off-by: Damian Krolik <damian.krolik@nordicsemi.no>
PHY overrides have been checked against the latest version of TI's
SmartRF(TM) Studio. The result was regression tested (PER/performance)
against LAUNCHXL-CC1352P1 boards.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
The length field in the header refers to the size of the MAC so it
shouldn't rely on constants describing PHY header length. While
currently both constants have the same value this will no longer be true
for enhanced PHYs and/or MAC frames as the number of FCS bytes may then
be four.
Also introduces an assertion that ensures that the given package buffer
does not exceed the TX buffer's length. An assertion is enough as the
package buffer is allocated at compile time.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
The CMD_CLEAR_RX and CMD_SET_TX_POWER commands are declared and
initialized but not used anywhere. They are therefore removed to reduce
RAM/flash footprint.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Switch the driver to the soft CSMA/CA algorithm as an intermediate
compromise for improved standard compliance (namely expontential
backoff) until true hardware support can be implemented by chaining
radio commands.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
The driver's CCA method had various issues and would always return an
error code. This is fixed in this change.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
This change introduces inline documentation with references to the
current version of the IEEE 802.15.4 standard.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
The CC13xx/CC26xx Sub-GHz driver announces a hardware CSMA/CA capability
which it provides only partially. This change documents the gap.
The change also fixes two related issues with the current CCA
implementation:
- The given default ED threshold was above the allowed threshold
defined in the specification.
- The CCA timeout was not calculated according to the requirements
defined in the standard.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
This change introduces standard variable names used elsewhere in the
stack for improved naming consistency and readability.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
The driver contained references to KConfig variables w/o the required
CONFIG_ prefix. This change introduces the missing prefixes.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
The low-level configuration of the chip's radio commands was mostly
redundant. This change removes redundant configuration code.
This is also relevant as a preparation to supporting further frequency
bands and operating modes on the same SUN FSK channel page with
similar but slightly different settings (center frequencies, channel
spacing, modulation index as defined in the standard). The SUN FSK
standard defines plenty of such variations with different physical
characteristics and trade-offs. Such variations are highly relevant in
industrial applications which will be targeted by TSCH. Using the
correct settings is required for additional features (e.g. frequency
hopping) and interoperability.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
The CC13xx/CC26xx Sub-GHz driver header file defined several constants
that were not used in the driver.
Other constants could be replaced with generic constants which were
introduced in the prior commit.
This change removes and/or replaces redundant definitions.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Acknowledgment is mandatory if legitimately requested by the package's
"ACK requested" flag. The L2 layer will have to ensure that compliant
ACK packages will always be sent out automatically as required by the
standard.
For IEEE 802.15.4 compliance, the NET_L2_IEEE802154_ACK_REPLY option is
therefore being deprecated.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
The existing calls to ieee802154_radio_send() and soft MAC ACK handling
were inconsistent and/or not properly integrated with more recent
radio driver capabilities as CSMA/CA and ACK in hardware.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
The method ieee802154_radio_handle_ack() does not belong to the
PHY/radio layer but to the L2 layer. It is a callback called from the
radio layer into the L2 layer and to be implemented by all L2 stacks.
This is the same pattern as is used for ieee802154_init(). The
'_radio_' infix in this function is therefore confusing and
conceptually wrong.
This change fixes the naming inconsistency and extensively documents
its rationale.
It is assumed that the change can be made without prior deprecation of the
existing method as in the rare cases where users have implemented custom
radio drivers these will break in obvious ways and can easily be fixed.
Nevertheless such a rename would not be justified on its own if it were
not for an important conceptual reason:
The renamed function represents a generic "inversion-of-control" pattern
which will become important in the TSCH context: It allows for clean
separation of concerns between the PHY/radio driver layer and the
MAC/L2 layer even in situations where the radio driver needs to be
involved for performance or deterministic timing reasons. This
"inversion-of-control" pattern can be applied to negotiate timing
sensitive reception and transmission windows, it let's the L2 layer
deterministically timestamp information elements just-in-time with
internal radio timer counter values, etc.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Add new `IEEE802154_CSL_DEBUG` Kconfig option that, when enabled,
prevents the radio to sleep after a delayed reception is finished.
This allows to debug CSL timing issues due to accuracy drifts in
communications between receiver and transmitter.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
The RSSI value in net_pkt (net_pkt_cb_ieee802154.rssi) was used
inconsistently across drivers. Some drivers did cast a signed dBm value
directly to net_pkt's unsigned byte value. Others were assigning the
negative value of the signed dBm value and again others were offsetting
and stretching the signed dBm value linearly onto the full unsigned byte
range.
This change standardizes net_pkt's rssi attribute to represent RSSI on
the RX path as an unsigned integer ranging from 0 (–174 dBm) to 254 (80
dBm) and lets 255 represent an "unknown RSSI" (IEEE 802.15.4-2020,
section 6.16.2.8). On the TX path the rssi attribute will always be
zero. Out-of-range values will be truncated to max/min values.
The change also introduces conversion functions to and from signed dBm
values and introduces these consistently to all existing call sites. The
"unknown RSSI" value is represented as INT16_MIN in this case.
In some cases drivers had to be changed to calculate dBm values from
internal hardware specific representations.
The conversion functions are fully covered by unit tests.
Fixes: #58494
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
The rf2xx does not check the return value from gpio_add_callback
function, which can prevent it from detecting unexpected states and
conditions. This add error processing check and log.
Fixes: #58595
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The IEEE802154_2015 option is misleading, as it does not introduce full
802.15.4-2015 standard compliance but only random bits, plus it's
defined at the radio driver level, which brings yet another confusion.
Because of that, the option will be deprecated, and respective parts of
code that made use of it converted to use more specific configurations:
* nRF driver will now use CONFIG_NRF_802154_ENCRYPTION to specify
whether to compile in TX security
* net_pkt will only add extra 802.15.4 control block fields if
OpenThread is used, as they were solely used by this L2
* OpenThread radio layer will now use the OpenThread version to
determine whether to compile in TX security.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Over time, some non-standard concepts and extensions were introduced
into the stack (in KConfig, in drivers, in the internal API and into the
implementation) which makes introduction of additional standard-
compliant extensions like TSCH (and others) unnecessarily difficult.
To introduce extensions like TSCH it is required for the IEEE 802.15.4
stack to become more structurally aligned with the standard again which
will be the focus of some of the upcoming preparatory changes.
One way to check and prove standard compliance is to reference the
standard from within the source code. This change therefore introduces
inline references to the IEEE 802.15.4-2020 standard wherever possible.
Deviations from the standard are documented with TODO or deprecation
labels to be addressed in future changes.
In the future, new code introduced to the IEEE 802.15.4 stack should
be documented and reviewed for standard-compliance to avoid further
divergence. Most importantly:
* MAC/PHY configuration (via net mgmt, radio API, devicetree or
KConfig) should always be directly linked to well-defined MAC/PHY
PIB attributes if visible to the MAC API or the end user.
* Net management/shell/radio API commands should have a documented
reference to the corresponding MLME action from the standard.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Functions nrf_802154_serialization_error and
nrf_802154_sl_fault_handler shall never return.
However `__ASSERT()` might expand to an empty instruction
CONFIG_ASSERT=n and is not enough to stop execution.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
some floats were getting promoted to doubles or they needed to be
casted as doubles to be used by printf
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
This case takes a float value and passes it to the integer abs function,
storing the result in an integer type variable. That looks like a possible
error to clang, so insert an explicit cast to int to make the compiler
happy.
Signed-off-by: Keith Packard <keithp@keithp.com>
Unify the drivers/*/Kconfig menuconfig title strings to the format
"<class> [(acronym)] [bus] drivers".
Including both the full name of the driver class and an acronym makes
menuconfig more user friendly as some of the acronyms are less well-known
than others. It also improves Kconfig search, both via menuconfig and via
the generated Kconfig documentation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
clean up redundant static functions
convert `csl_rx_time` to uint32_t and remove redundant `nrf5_schedule_rx`
`nrf5_config_csl_period` and `nrf5_receive_at` static functions.
`csl_rx_time` has been passed as uint32. It is compared to uint64 value
returned by `nrf_802154_sl_timer_current_time_get` in
`nrf_802154_ie_writer.c` which leads to wrong calculation of phase in CSL.
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
Currently the 2.4G radio driver for CC1352 has few implementations which
prevents both the radios to be used in a single build, thus preventing
applications to have different builds to switch the RF bands even though
the hardware supports dual bands simultaneously.
The following updates are made:
* Remove RF patches from stack.
* Implement if_stop() to stop the interface and yield the interface.
* Use RF_runCmd() instead of RF_runImmediateCmd() so that two RF handles
can work simultaneously.
All the updates are similar to the more recent cc13xx subg driver which
implements all these recommended practices already.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
During extended testing, rx_done() callback was seen to be invoked with
zero-length packets.When RAW_MODE is enabled, CRC is being appended to
these packets thus making downstream consumers think the packet is valid.
Root cause of the callback being invoked with zero-length packet is
unknown, but appending CRC to these packets is incorrect, thus fix it.
Also fix a minor error which causes build failure when
CONFIG_NET_L2_IEEE802154_SUB_GHZ is not defined.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Adding an Openthread radio API `otPlatRadioSetMacFrameCounterIfLarger`
implementation and the corresponding call to the IEEEE802154 driver.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
Correct bit mask for RF2XX_RX_TRAC_BIT_MASK. Current mask produce dead
code warnings when comparing to value:
RF2XX_TRX_PHY_STATE_TRAC_INVALID = 0x07
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The ISR prototype was changed some time ago
(6df8b3995e)
to (const void*) => fix the prototype used when
CONFIG_IEEE802154_NRF5_EXT_IRQ_MGMT is not set
to avoid a compile warning.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Added new CC1352P1 LaunchXL board supporting 20dBm TX for its
sub-GHz radio.
Note that the board has a multiplexer circuit to switch between
2.4GHz, High-Power TX and Sub1GHz states, for which a custom board
module was implemented, together with board-specific device-tree
bindings and pinctrl definitions for each of the RF states.
Signed-off-by: Stancu Florin <niflostancu@gmail.com>
Enhance IEEE802154 Sub-GHz driver to support CC13x2P's internal power
amplifier (20dBm) for TX.
Note: requires board-specific antenna switching for it to work
properly.
Signed-off-by: Stancu Florin <niflostancu@gmail.com>
When transceiver is overload on reception a frame can be stored on
the internal buffer without processing a frame start interrupt. The
frame will complete and system will received a interrupt and signal
receiver thread with an isr_status equal to 0x2c.
The current implementation process one flag at time and it may hang
when status is 0x2c. This issue can be reproduced using two nodes
where one perform a regular TX broadcast and tThe other one should
be wait for frames. The receptor should run on debug mode and system
should be started normally. The problem happens when pressing CTRL+C
on the debugger, which will cause system to stop. However, the
transceiver still can receive one last frame. After a few transmission
user can continue application and a isr_status of 0x2c will be visible
if CONFIG_IEEE802154_DRIVER_LOG_DEBUG is enabled.
This fixes the current issue by processing all RF2XX_TRX_END events.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Clean up occurrences of "#if IS_ENABLED(CONFIG_FOO)" an replace
with classical "#if defined(CONFIG_FOO)".
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
`spi_is_ready` function is being deprecated in favor of
`spi_is_ready_dt` so let's replace the old usage in the tree.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
Add CONFIG_CRC for building CRC related routines.
CRC routines are now being built for each application, whether used or
not and are add in the build system unconditionally.
Keep CONFIG_CRC enabled by default for now and until all users have
converted to use the new option.
Partial fix for #50654
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
net_pkt_get_frag() and a few other functions did not specify the
allocated fragment length, incorrectly assuming that fixed-sized
buffers are always used.
In order to make the function work properly also with variable-sized
buffers, extend the function argument list with minimum expected
fragment length parameter. This allows to use net_buf_alloc_len()
allocator in variable buffer length configuration, as well as verify if
the fixed-sized buffer is large enough to satisfy the requirements
otherwise.
Update the existing codebase to provide the expected fragment length,
based on the context.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Since nRF IEEE 802.15.4 radio driver is now capable of calculating CSL
phase based on provided anchor time and CSL period, the CSL placeholder
window is no longer necessary. This commit removes it and switches to
the new calculation method.
Signed-off-by: Artur Hadasz <artur.hadasz@nordicsemi.no>
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
This change implements part two of the program laid out in the TSCH RFC,
see #50336#issuecomment-1250250154 :
> Consolidate IEEE 802.15.4 options in net_pkt
This change improves decoupling of generic net core code from
IEEE 802.15.4 internals. It also simplifies IEEE 802.15.4
attribute cloning and thereby makes it easier to maintain and less
error prone (and probably even faster as individual bits are no longer
copied over separately).
This enables us to extend and design IEEE 802.15.4 L2 attributes inside
the package in isolation from the net core code which will no longer
have to be changed when introducing changes or additions to the flags.
This flexibility will be built upon in later change sets to model the
IEEE 802.15.4 attributes closer to the spec.
The solution is inspired by Linux's sk_buff->cb attribute which addresses
the same concern as the attribute introduced in this change set:
https://elixir.bootlin.com/linux/v6.0.1/source/include/linux/skbuff.h#L871
As the inline comment says: The cb attribute can be made a union or even a
uint8[something] in the future, if further L2s need a control block, too.
Right now such full indirection would make the code overly abstract, so
I chose to compromise with maintainability in mind.
Care has been taken to ensure that this changes does not introduce
additional padding into the net package. To maintain zero-padding, future
changes to the net packet struct will have to ensure that the
IEEE 802.15.4 struct is 4-byte aligned (iff the IEEE 802.15.4 struct
continues with max uint32_t scalar members) which is no deviation from
the previous implementation.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
Nordic's IEEE 802.15.4 radio driver adapter layer had a few raw accesses
to net packet attributes.
Packet attributes should never be accessed directly, though, but only
through the dedicated accessor methods provided by the net core.
This change replaces raw accesses to packet attributes by their
respective wrapper functions.
This also is a necessary precondition to the isolation and
encapsulation of IEEE 802.15.4 specific packet attributes which will be
introduced in a later commit of this change set.
Fixes: #51264
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
Several IEEE 802154 drivers allocated RX packets from the TX pool.
This may seem like a minor problem at first sight but it may become
problematic if the pool is used to distinguish package types as is the
case in some code paths, e.g. for packet priority or determination of
the packet buffer pool.
This bug also has the potential of starving the TX pool capacity which
even may make devices vulnerable to DoS attacks as sending may be
prohibited by addressing enough RX packets to a device to let it run out
of TX capacity.
Fixes: #51261
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
Change automated searching for files using "IRQ_CONNECT()" API not
including <zephyr/irq.h>.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The IEEE 802.15.4 radio driver encodes attributes in:
* little endian for everything that is close to the protocol as
IEEE 802.15.4 frames are little endian encoded.
* mixed big and little endian in its configuration where extended
addresses are being represented. These inconsistencies are unfortunate
but cannot be easily fixed in a backwards compatible way so will be
left untouched in this change.
Endianness was almost nowhere documented which explains these
inconsistencies and led to several bugs where assignments of different
byte order are not converted (or sometimes converted, sometimes not).
This change documents intended endianness within the realm of the
IEEE 802.15.4 radio driver code. Conversion bugs are fixed in a separate
commit.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
Add support to at86rf212[b] sub-giga devices. This work enables use of
pages 0, 2 and 5 in accordance with IEEE-802.15.4/2003/2006/2011. The
proprietary speeds can be object of future work.
Note: It is recommended that user define a power table for better
performance, low emissions and to save power. A reference power table
can be found in the datasheet and should be used for tests only and
not on a final product.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The current version of power table is hardcoded in the driver which is a
problem when use devices in production. This change remove all hardcode
from driver and reimplement the feature to allow people create a table
which is defined in devicetree. The big advantage is that each board can
define their own table based on lab tests and allows use of FEM devices
inclusive.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This change applies the newly introduced consistent MTU definition to
all IEEE 802.15.4 radio drivers.
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
Many device pointers are initialized at compile and never changed. This
means that the device pointer can be constified (immutable).
Automated using:
```
perl -i -pe 's/const struct device \*(?!const)(.*)= DEVICE/const struct
device *const $1= DEVICE/g' **/*.c
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Activating both, the IEEE 802.15.4 raw mode /and/ the L2 mode is not
possible and in fact leads to a build error.
It should therefore not be possible to activate both options at the same
time. This is achieved by only offering the (rather exotic) raw mode
once the L2-support for the IEEE 802.15.4 has been switched off.
Fixes: #48715
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
Previous to this change, each individual driver option depended on
NETWORKING. Instead, move dependency one level up.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Make all drivers default to 'y' and dependent on being enabled in DT.
This will allow simplifying many samples/tests.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the UART UPIPE IEEE 802.15.4 driver. This
allows to remove usage of IEEE802154_UPIPE_DRV_NAME in preparation for
the removal of NET_CONFIG_IEEE802154_DEV_NAME.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the radio and IEEE 802.15.4. This allows to
remove usage of IEEE802154_NRF5_DRV_NAME in preparation for the
removal of NET_CONFIG_IEEE802154_DEV_NAME.
All SoC files have been updated with the addition of an ieee802154 node
(disabled and only on those SoCs that define ieee802154-supported. The
peripheral has been enabled in the nRF52840DK board (used for testing
ieee802154).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the radio and IEEE 802.15.4. This allows to
remove usage of IEEE802154_KW41Z_DRV_NAME in preparation for the removal
of NET_CONFIG_IEEE802154_DEV_NAME.
KW41Z files have been updated with the addition of radio and an
ieee802154 nodes The peripheral has been enabled in the frdm_k41z board
(used for testing ieee802154).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The crypto driver is used internally, so there's no real need to expose
its name as a Kconfig option. Just drop it in favor of a plain string
with the same previous value.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the radio and IEEE 802.15.4. This allows to
remove usage of IEEE802154_CC13XX_CC26XX_SUBG_DRV_NAME in preparation
for the removal of NET_CONFIG_IEEE802154_DEV_NAME.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the radio and IEEE 802.15.4. This allows to
remove usage of IEEE802154_CC13XX_CC26XX_DRV_NAME in preparation for the
removal of NET_CONFIG_IEEE802154_DEV_NAME. All boards used in testing
have been updated to enable the peripheral in DT as well.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the radio and IEEE 802.15.4. This allows to
remove usage of IEEE802154_CC1200_DRV_NAME in preparation for the removal
of NET_CONFIG_IEEE802154_DEV_NAME.
In this case, the driver already had bindings, however, it was still
using NET_DEVICE_INIT.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
MISRA C:2012 Rule 14.4 (The controlling expression of an if statement
and the controlling expression of an iteration-statement shall have
essentially Boolean type.)
Use `do { ... } while (false)' instead of `do { ... } while (0)'.
Use comparisons with zero instead of implicitly testing integers.
The commit is a subset of the original auditable-branch commit:
5d02614e34a86b549c7707d3d9f0984bc3a5f22a
Signed-off-by: Simon Hein <SHein@baumer.com>
Move driver to use {NET_}DEVICE_DT_INST_DEFINE. This lets us
remove the IEEE802154_CC2520_DRV_NAME Kconfig symobl.
We also update the ieee802154 build_all test to actually enable
the CC2520 driver.
Signed-off-by: Kumar Gala <galak@kernel.org>
Move driver to use {NET_}DEVICE_DT_INST_DEFINE. This lets us
remove the IEEE802154_B91_DRV_NAME Kconfig symobl.
Signed-off-by: Kumar Gala <galak@kernel.org>
irq_lock() returns an unsigned integer key.
Generated by spatch using semantic patch
scripts/coccinelle/irq_lock.cocci
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
The uart_pipe driver is not dependent on any console driver,
however a serial driver is required.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
This commit fixes a bug where an already received Rx frame could not be
processed by the IEEE 802.15.4 driver.
In the current implementation, buffer is marked as free and released to
the buffer pool after `nrf_802154_buffer_free_raw` finishes executing.
However, delays caused by thread scheduling might result in a new frame
being already received and provided to the driver before
`nrf_802154_buffer_free_raw` returns. Such a situation ends in an
assertion now.
This commit changes that behavior by marking the buffer as free before
calling `nrf_802154_buffer_free_raw`.
Signed-off-by: Jedrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
This commit increases verbosity of serialization error handler for
nRF5340 application core. The handler prints the error code now.
Signed-off-by: Jedrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
Since the driver uses spi_dt_spec there is no need for an explicit
spi_cs_control variable. The variable is unused.
Signed-off-by: Kumar Gala <galak@kernel.org>
Files including <zephyr/kernel.h> do not have to include
<zephyr/zephyr.h>, a shim to <zephyr/kernel.h>.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This commit extends Nordic's ieee802154 driver with the possibility to
set Tx power for every transmission separately.
Signed-off-by: Jedrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
This commit extends the `struct net_pkt` structure with
`ieee802154_txpwr` field that contains signed value of the desired
transmission power of a IEEE 802.15.4 frame in dBm.
Signed-off-by: Jedrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
This PR introduces a fix for DRX window being triggered to early during
CSL. Fixes were also introduced in the nrf 802154 radio
driver, so removed the unneeded DRX_ADJUST constant.
Signed-off-by: Artur Hadasz <artur.hadasz@nordicsemi.no>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
After change in RD into 64-bit time, target time must be express in
absolute 64-bit time. Upper layer e.g. OpenThread still utilizes only
LSB of the RD time therefore the conversion is required.
Make sure that target time is absolute 64-bit target time.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
For delayed reception only NRF_802154_RX_ERROR_DELAYED_TIMEOUT is
expected to happen, others rx errors should be handled in regular
manner.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
Some failures are possible and expected from fime to time e.g.
NRF_802154_RX_ERROR_TIMESLOT_ENDED. Add informational log for the frame
reception failure to differentiate the specific case.
It can be helpful for analizing failure in network trafic.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
Allows the setting of ieee802154 EUI64 address in non-secure processing
environment by reading the FICR device ID through the secure service.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Currently IEEE802154_NRF5_DELAY_TRX_ACC can exceed the max possible
value. Add upper bound to limit this.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
Align clock accuracy used in CSL calculations to the value in platform.
This is recomended setting for devices working in wide range
temperature. Nevertheless it can be profiled in end product to decrease
CSL window duration and finally the power consumption.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
