Acknowledgment is mandatory if legitimately requested by the package's
"ACK requested" flag. The L2 layer will have to ensure that compliant
ACK packages will always be sent out automatically as required by the
standard.
For IEEE 802.15.4 compliance, the NET_L2_IEEE802154_ACK_REPLY option is
therefore being deprecated.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
The method ieee802154_radio_handle_ack() does not belong to the
PHY/radio layer but to the L2 layer. It is a callback called from the
radio layer into the L2 layer and to be implemented by all L2 stacks.
This is the same pattern as is used for ieee802154_init(). The
'_radio_' infix in this function is therefore confusing and
conceptually wrong.
This change fixes the naming inconsistency and extensively documents
its rationale.
It is assumed that the change can be made without prior deprecation of the
existing method as in the rare cases where users have implemented custom
radio drivers these will break in obvious ways and can easily be fixed.
Nevertheless such a rename would not be justified on its own if it were
not for an important conceptual reason:
The renamed function represents a generic "inversion-of-control" pattern
which will become important in the TSCH context: It allows for clean
separation of concerns between the PHY/radio driver layer and the
MAC/L2 layer even in situations where the radio driver needs to be
involved for performance or deterministic timing reasons. This
"inversion-of-control" pattern can be applied to negotiate timing
sensitive reception and transmission windows, it let's the L2 layer
deterministically timestamp information elements just-in-time with
internal radio timer counter values, etc.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
The RSSI value in net_pkt (net_pkt_cb_ieee802154.rssi) was used
inconsistently across drivers. Some drivers did cast a signed dBm value
directly to net_pkt's unsigned byte value. Others were assigning the
negative value of the signed dBm value and again others were offsetting
and stretching the signed dBm value linearly onto the full unsigned byte
range.
This change standardizes net_pkt's rssi attribute to represent RSSI on
the RX path as an unsigned integer ranging from 0 (–174 dBm) to 254 (80
dBm) and lets 255 represent an "unknown RSSI" (IEEE 802.15.4-2020,
section 6.16.2.8). On the TX path the rssi attribute will always be
zero. Out-of-range values will be truncated to max/min values.
The change also introduces conversion functions to and from signed dBm
values and introduces these consistently to all existing call sites. The
"unknown RSSI" value is represented as INT16_MIN in this case.
In some cases drivers had to be changed to calculate dBm values from
internal hardware specific representations.
The conversion functions are fully covered by unit tests.
Fixes: #58494
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
`spi_is_ready` function is being deprecated in favor of
`spi_is_ready_dt` so let's replace the old usage in the tree.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
Several IEEE 802154 drivers allocated RX packets from the TX pool.
This may seem like a minor problem at first sight but it may become
problematic if the pool is used to distinguish package types as is the
case in some code paths, e.g. for packet priority or determination of
the packet buffer pool.
This bug also has the potential of starving the TX pool capacity which
even may make devices vulnerable to DoS attacks as sending may be
prohibited by addressing enough RX packets to a device to let it run out
of TX capacity.
Fixes: #51261
Signed-off-by: Florian Grandel <jerico.dev@gmail.com>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Simplify driver implementation by using spi_dt_spec. Most internal
functions now take a device reference to simplify the operation, since
config did not exist before.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device already has a DT compatible (and uses DT properties).
Instantiate the device using the DT-based macros and remove hardcoded
name.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Convert drivers to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In all of these drivers, passing the device's data was sufficient as
only the data is being used by thread.
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Even though radio driver can report in its capabilities that it does
support CSMA CA, there's no way in the driver to select how the frame
should be transmitted (with CSMA or without). As layers above radio
driver (Thread, Zigbee) can expect that both TX modes are available, we
need to extend the API to allow either of these modes.
This commits extends the API `tx` function with an extra parameter,
`ieee802154_tx_mode`, which informs the driver how the packet should be
transmitted. Currently, the following modes are specified:
* direct (regular tx, no cca, just how it worked so far),
* CCA before transmission,
* CSMA CA before transmission,
* delayed TX,
* delayed TX with CCA
Assume that radios that reported CSMA CA capability transmit in CSMA CA
mode by default, all others will support direct mode.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
By changing the various *NET_DEVICE* macros. It is up to the device
drivers to either set a proper PM function or, if not supported or PM
disabled, to use device_pm_control_nop relevantly.
All existing macro calls are updated. Since no PM support was added so
far, device_pm_control_nop is used as the default everywhere.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Convert driver to use DT_INST_ defines. There was just one case for
CS_GPIOS that wasn't using DT_INST defines already.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use the named representation for no-wait to future-proof against a
change to the representation of timeout values.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
move misc/byteorder.h to sys/byteorder.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert DT_.*_GPIO_{CONTROLLER,PIN,FLAGS} ->
DT_.*_GPIOS_{CONTROLLER,PIN,FLAGS)
Used the following commands to make these conversions:
git grep -l DT_.*_GPIO_CONTROLLER | xargs sed -i 's/DT_\(.*\)_GPIO_CONTROLLER/DT_\1_GPIOS_CONTROLLER/g'
git grep -l DT_.*_GPIO_PIN | xargs sed -i 's/DT_\(.*\)_GPIO_PIN/DT_\1_GPIOS_PIN/g'
git grep -l DT_.*_GPIO_FLAGS | xargs sed -i 's/DT_\(.*\)_GPIO_FLAGS/DT_\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This macro is slated for complete removal, as it's not possible
on arches with an MPU stack guard to know the true buffer bounds
without also knowing the runtime state of its associated thread.
As removing this completely would be invasive to where we are
in the 1.14 release, demote to a private kernel Z_ API instead.
The current way that the macro is being used internally will
not cause any undue harm, we just don't want any external code
depending on it.
The final work to remove this (and overhaul stack specification in
general) will take place in 1.15 in the context of #14269Fixes: #14766
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
15.4 MHR is no longer set in net_buf pointed by net_pkt, but in a
separate net_buf, hence we need to check that net_buf now to
determine if we need to wait for ACK or not.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Moving towards serialized fragmentation, adapting mac command creation
to avoid the need of ll_reserve etc...
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Do not initialize reset gpio on KW2XD SIP.
Modem's clock output is used by the SoC for the PLL.
Initialization of the reset gpio may result in the reset of the modem
and the crash of SoC.
Keep reset gpio low until modem initialization.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Fix overwrites update of indirect register.
Since the indirect register should be updated,
the parameter dreg should be false.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
As for Ethernet, up to ieee802154 L2's send to actually sent the packet.
It's currently unoptimized as 6lo compression, 15.4 fragmentation and so
on will reallocate net_buf etc... but it's the first step towards
removing ll reserve space and more.
Applying changes to Openthread L2 as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that all SPI controllers support DTS we can remove the Kconfig
support for non-DTS options. We also cleanup some defines that should
have be DT_MCR20A_ instead of CONFIG_MCR20A_.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Allow to set debug also for RAW_CHANNEL and set general debug template
instead of networking one.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
