The pga enum internal reference voltage and gain values
were fixed in the code, but a comment was forgotten to be
updated. Correct the comment to match how the code uses
the enum.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
This patch ensures that the power domain to which the current HD DMA
instance belongs is power-up first.
In addition, it initializes the channels when coming out of SUSPEND
state, so this operation will be performed also when the stream is
started after the DSP comes out of D3 state.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
os.path.commonpath() throws a ValueError exception when paths in the
list provided share nothing in common (like for example two Windows
paths on different drive letters). Handle that special case properly
instead of letting the exception propagate up.
Fixes#51549.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The Boron has a power switch that controls power to a level shifter
for the modem's serial line. Previously, this switch was being enabled
after the modem driver had already started. It is now controlled using
a fixed regulator.
The board initialization was also configuring the V_INT_DETECT pin.
However, this pin is already handled as mdm-vint-gpios in the dts when
the ublox-sara-r4 driver is used. Since it is not used otherwise,
there is no need to configure it in the board init.
Fixes: #56883
Signed-off-by: Göran Weinholt <goran@weinholt.se>
Change the assertion when evaluating the baudrate to trig if
result is greater or equal to 16.
This will also match the comment : checking BRR.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Mocks used in the test were not initializing certain variables.
Valgrind detected that. Test was passing but could fail if some
garbage would end up in that memory.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
The tachometer collects the data continuously setting a "data ready" bit
when it's ready. The availability bit has to be cleared before the
register is updated.
The driver also supports underflow detection, when the bit indicating it
is set the reading of "0" is returned.
The problem here is that there is that once the underflow bit is cleared
we might end up reading stale data.
To prevent that clear the "data ready" bit when underflow is detected
Signed-off-by: Kornel Dulęba <mindal@semihalf.com>
Fix the OTRIG related build error in the DMA LPC
by defaulting num_of_otrigs to 0 if a plarform using
the LPC DMA does not specify this property in devicetree.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
For Intel cavs2.5, access from LPGPDMAC to Audio Link Hub
RX/TX registers needs to be explicitly enabled before use.
The logic follow hardware initialization done in
SOF project sof/src/platform/intel/cavs/platform.c
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Found EMSDP board SPI-FLASH sample broke after adding DFSS
into spi_dw. Found wrong interrput mask resulting in false
interrupt enabled. Now fixed it to fit both DFSS and DW.
Signed-off-by: Siyuan Cheng <siyuanc@synopsys.com>
Set up a test fixture to reduce repetition and split
testsuite into blocking and nonblocking tests.
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
Include standard headers first, and then ensure that the
convention of `<zephyr/posix/...>` is followed for internal
POSIX sources.
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
In order to reduce churn in CI, test only with the default libc.
Additionally, reduce Kconfig options in `prj.conf` to minimum.
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
Up until now, it has not been possible to reconfigure a CIG and its
CISes after initial configuration, without first removing the CIG.
With this commit, le_set_cig_parameters allows the following
reconfiguration operations in configuration state:
- Set new CIG configuration parameters on existing CIG
- Iteratively configure single CIS (of more CISes)
- Increment number of CISes via multiple configuration calls
- Keep handle- and CIS_ID relation
Changes:
- Pass handles in le_set_cig_parameters from ll_cig_parameters_commit
via output variable.
- Implement CIG state variable instead of 'started', with states
IDLE/CONFIGURABLE, ACTIVE and INACTIVE.
- Implement ll_conn_iso_stream_get_by_id for easier access to specific
CIS.
This fixes the following CIS Central EBQ tests:
- HCI/CIS/BI-10-C
- HCI/CIS/BI-11-C
- HCI/CIS/BI-13-C
- HCI/CIS/BV-05-C
Signed-off-by: Morten Priess <mtpr@oticon.com>
The path_dir variable of BT_HCI_OP_LE_REMOVE_ISO_PATH must be bitflags,
with the following meaning:
- BIT(0) : DIR_HOST_TO_CTLR
- BIT(1) : DIR_CTLR_TO_HOST
Signed-off-by: Morten Priess <mtpr@oticon.com>
According to the Core spec, the direction parameter passed to this function
should be bitfields, i.e.:
- BIT(0) : DIR_HOST_TO_CTLR
- BIT(1) : DIR_CTLR_TO_HOST
Signed-off-by: Morten Priess <mtpr@oticon.com>
This option is relevant enough to appear in the release notes, since it
is helpful to ease the debugging of a frequent issue.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
TF-M changes are documented in another section of the document, this is
likely a merge mistake.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use phase shift between the emulated A and B signals equal to the half
of the used period instead of a fixed 1 millisecond, to not enforce
decoders to use relatively frequent sampling just to make use of this
emulation.
Add also a few missing `static` keywords.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This is a follow-up to commit 09fa46ee4e.
Before nrfx 3.0, the QDEC interrupt on REPORTRDY event was activated
implicitly when a `reportper` value other than `DISABLED` was used.
Now, the `reportper_inten` field needs to be used to activate this
interrupt.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
When calling twister with --coverage and no platform specified on the
command line, set the the value of coverage platforms to an empty list.
Fixes#57534
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This set tests if Private Beacons are advertised properly, with address
changed for every beacon and Random value changing appropriately
regarding the scenario (IV Update, Key Refresh, advertisements on device
with friendship support) and Random Interval state.
All tests contain two devices: tx advertises Private Beacon (has Private
Beacon Server in composition) and rx sets Private Beacon state on tx
device (has Private Beacon Client). On rx device, scan callback is
registered to monitor Private Beacon advertisements.
Signed-off-by: Krzysztof Kopyściński <krzysztof.kopyscinski@codecoup.pl>
In `private_random_update`, when first beacon is advertised, there could
be a case when uptime is less then interval * 10s
(`priv_random.timestamp` is equal to 0 for first beacon). Then, Private
Random value will not be generated and will be set to all zeros.
New Private Random must also be generated before Random Interval
expires, when KR or IVU flags are changed. Reset timestamp to 0 on
`bt_mesh_beacon_update` to generate new Random value.
Do not generate new private random if it won't be used (Private Beacon
state is not enabled).
Signed-off-by: Krzysztof Kopyściński <krzysztof.kopyscinski@codecoup.pl>
cpu_node_list does not hold the corrent mapping of cpu id and mpid when
core booting sequence does not follow the DTS cpu node sequence. This
will cause an issue that sgi cannot deliver to the right target.
Add the cpu_map array to hold the corrent mapping between cpu id and
mpid.
Signed-off-by: Jaxson Han <jaxson.han@arm.com>
Each core should init their own stack during the reset when SMP enabled,
but do not touch others. The current init results in each core starting
init the stack from the same address which will break others.
Fix the issue by setting a correct start address.
Signed-off-by: Jaxson Han <jaxson.han@arm.com>
LOG system has unalignment access instruction which will cause an
alignment exception before MPU is enabled. Remove the LOG print before
MPU is enabled to avoid this issue.
Signed-off-by: Jaxson Han <jaxson.han@arm.com>
The test case will show an unexpected exception in the idle thread after
all test cases pass. The issue is caused by the main thread
stackoverflow.
Increase the main stack configured in this test case to fix the issue.
Signed-off-by: Jaxson Han <jaxson.han@arm.com>
