Adds checking that qualifiers listed in a soc.yml file are valid
for the socs and cpuclusters defined in that file
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Adds configuration that allows nRF53 and nRF91-based boards to be
flashed through west using sysbuild for multiple images with the
recover or erase options and prevent running those commands for
each image being flash, which would make the device unbootable.
Also defers reset whilst all images for the cores of these SoCs
are flashed.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
This adds supports for flashing images with sysbuild where there
are multiple images per board to prevent using the same command per
image flash which might cause issues if they are not ran just once
per flash per unique board name. A deferred reset feature is also
introduced that prevents a board (or multiple) from being reset if
multiple images are to be flashed until the final one has been
flashed which prevents issues with e.g. security bits being enabled
that then prevent flashing further images.
These options can be set at a board level (in board.yml) or a SoC
level (in soc.yml), if both are present then the board configuration
will be used instead of the SoC, and regex can be used for matching
of partial names which allows for matching specific SoCs or CPU cores
regardless of the board being used
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
esp32 platforms can overflow its dram0_0_seg and dram0_1_seg.
So update current dram section to meet both cases.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
qemu_malta//be -> qemu_malta/qemu_malta/be
This caused the board not to work with Twister.
Signed-off-by: Øyvind Rønningstad <oyvind.ronningstad@nordicsemi.no>
Updates z_get_next_switch_handle() to set the new thread's base.cpu
value as it is done in do_swap(). This helps to ensure that the
last CPU on which the thread executed remains current.
Signed-off-by: Peter Mitsis <peter.mitsis@intel.com>
Removed following fields from relevant Handlers,
as they were unused in code:
* Handler's state
* Handler's generator
* BinaryHandler's call_west_flash
* QEMUHandler's results
* QEMUWinHandler's results
Signed-off-by: Lukasz Mrugala <lukaszx.mrugala@intel.com>
Found via static analysis. In fault path when checking for stack
overflows, if CONFIG_MULTITHREADING is not set, `guard_end` is left
uninitialized and is subsequently used in a comparison.
The solution is to simply return `false` in this configuration as stack
guards are not configured in the first place.
Signed-off-by: François Baldassari <francois@memfault.com>
This commit reverts a breaking change in CMAKE_SYSTEM_NAME introduced by
"Zephyr" back to "Generic") and removes the file
`cmake/modules/Platform/Zephyr`.
Both changes in the aforementioned PR were only introduced to ultimately
modify the value of the global CMake property TARGET_SUPPORTS_SHARED_LIBS
for the special case of building for Xtensa with LLEXT.
The modification of CMAKE_SYSTEM_NAME is considered a breaking change
because it has the potential to alter the build of any non-trivial project
that previously checked for the "Generic" system identifier as
corresponding to Zephyr - for example by doing
`if (CMAKE_SYSTEM_NAME STREQUAL "Generic")`. Such builds may now break in
many ways including silently when there is no `else()` clause with a
`message()` to alert the user that a whole configuration block had been
skipped.
In essence, that CMAKE_SYSTEM_NAME modification was only introduced in
order to have CMake to load `cmake/modules/Platform/Zephyr.cmake` which in
turn adjusted the value of TARGET_SUPPORTS_SHARED_LIBS.
But the use of a CMake platform file like this is ineffective for
non-trivial projects where one or more top level CMake `project()` calls
may happen before the first call to `find_package(Zephyr)` because in such
cases CMAKE_MODULE_PATH will not have been modified yet to contain the
path to <Zephyr_ROOT>/cmake/modules and thus no platform file will be
include by CMake.
This patch moves the conditional override of TARGET_SUPPORTS_SHARED_LIBS
needed by some archs (e.g. Xtensa) into the `kernel.cmake` module which
is known to be the first call to `project()` that enables any language and
thus the one that must come before any artifact target can be defined.
Note commit 64e7d85 added a Kconfig to specify the object type of llext
being built, so it's not tied to the arch anymore but to the
CONFIG_LLEXT_TYPE_ELF_SHAREDLIB option.
Signed-off-by: Nicolas Lebedenco <nicolas@lebedenco.net>
Adds release notes about the addition of a socs folder for
applications to store Kconfig fragments and devicetree overlays
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Adds details about Kconfig fragments and devicetree overlay files
that will be included in a build if they are found in the
``socs`` folder
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Adds support for SoC overlay files which go in a ``socs`` folder
in application folders and functions similar to the ``boards``
folder, but works for SoCs instead of boards
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Adds support for a new ``socs`` folder that can be placed in
application folders and functions similar to the ``boards``
folder, but works for SoCs instead of boards
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Some third-party modules uses 'find_package(Threads REQUIRED)' to check
if threads implementation is supported.
The original implementation tries to find threads library using various
methods (e.g. checking if pthread library is present or compiling
example program to check if the implementation is provided by libc), but
it's not able to detect pthread implementation provided by Zephyr.
Signed-off-by: Patryk Duda <patrykd@google.com>
Fixes an issue with zephyr modules not being listed in sysbuild if
they did not have a Kconfig file set
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Unlike GNU ld, lld's gp relaxation is disabled by default and must be
explicitly enabled via `--relax-gp`. Pass this flag to enable gp relaxation
for lld when both linker relaxations and gp usage for RISC-V are enabled.
Signed-off-by: Jonathon Penix <jpenix@quicinc.com>
The sysbuild_cache_set() supports setting variables in a dedicated
sysbuild image cache. When appending to a list, the list is checked for
existance of the variable to avoid appending it again on reruns.
This was done be checking with `string(FIND ...)`, but that will also
return an index on a partial match.
A much safer approach is to use the `if(<val> IN_LIST <list>)` approach
to check for existance.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
To allow easily building samples using the shell, without needing to
specify additional configurations. Tested with:
```
west build -b nrf52840dk/nrf52840 \
-S nus-console` \
samples/subsys/shell/shell_module
```
Signed-off-by: Luis Ubieda <luisf@croxel.com>
The Synopsys Designware SPI peripheral exists in two versions with
slightly different register layouts. Added a Kconfig option that makes the
driver compatible with the HSSI register layout.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Add a diagram that was first created for eoss 2024 to help
visualize the relation between the different application
environment profiles of IEEE 1003.13-2003.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
The POSIX Application Environment Profiles are additive and
offer incrementally more features over the System Interfaces.
For example, PSE51 includes all of the features of the Minimal
Realtime System Profile plus all of the System Interfaces.
PSE52 includes all of the features of the Realtime Controller
System Profile, plus the features of PSE51, plus the System
Interfaces, and so on.
It makes sense to take advantage of that and to condense the
AEP documenation.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Define additional options and option groups for PSE51 to PSE53.
The options groups added in this commit are:
POSIX_SIGNAL_JUMP
POSIX_FILE_SYSTEM
POSIX_PIPE
POSIX_FILE_LOCKING
The options added in this commit are:
_POSIX_MEMLOCK
_POSIX_MEMLOCK_RANGE
_POSIX_MONOTONIC_CLOCK
_POSIX_SHARED_MEMORY_OBJECTS
_POSIX_THREAD_CPUTIME
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Previously, some links were not resolving properly since they
lacked the :ref: prefix, so it was added.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Add mps2/an385 and unit_testing to the simulator
criteria while parsing testsuites. Now the testsuit
will count as a simulator only where the platform
is quemu*, native*, unit_testing, mps2/an385.
Signed-off-by: Arkadiusz Cholewinski <arkadiuszx.cholewinski@intel.com>
The function writes random data to the provided buffer. Maximum
permitted buffer size is 256 bytes. On success the function returns 0,
otherwise it returns -1 and sets errno to appropriate value.
Signed-off-by: Patryk Duda <patrykd@google.com>
Unicast RX stats
It represents total number of unicast (any type data, action or
any other unicast frames) frames received at firmware level.
The actual frames passed to host will be different as firmware
may drop packets or some packets may be dropped because of
errors.
Unicast TX stats
Transmission side the unicast packets count states the packets
handed over to firmware. The stats taken at firmware level.
Actual packets transmission may vary depending upon various factors.
Signed-off-by: Ajay Parida <ajay.parida@nordicsemi.no>
Add USB out support for the BAP shell, so that decoded LC3
data can be sent to the host (e.g. a PC).
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The volume controller always set the busy flag in
bt_vcp_vol_ctlr_set_vol, where it should only set it
if the GATT operation succeeds.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
For historical reasons, inversion mode is enabled by default in the
current implementation. This commit introduces an `inversion-off`
boolean DTS property, allowing it to be disabled if necessary.
Signed-off-by: Chen Xingyu <hi@xingrz.me>
Mark the _POSIX_ASYNCHRONOUS_IO headers as supported, and note
the deviation that they return -1 and set errno to ENOTSUP.
At some later date, it might be possible to implement the
standard functions with other Zephyr API calls.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Add tests to ensure that the aio.h header exists, the
structures are declared, and that the functions are present.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Add stubs for POSIX asynchronous io that return -1 and set
errno to ENOTSUP.
The functions and structures in aio.h are required by the
_POSIX_ASYNCHRONOUS_IO Option as detailed in Section E.1 of
IEEE-1003.1-2017.
The _POSIX_ASYNCHRONOUS_IO interface is required for PSE51,
PSE52, PSE53, and PSE54 conformance, and is otherwise mandatory
for any POSIX conforming system as per Section A.2.1.3 of
IEEE-1003-1.2017.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Test that the Host give back the correct error when we try to set too
big advertising data. And ensure that long advertising data are
correctly transmitted.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
Send a `READ_MAX_ADV_DATA_LEN` command to the controller at the
initialization of the host to fetch the maximum advertising data length
the host can accept.
This is done because even if the Zephyr controller provide the
`CONFIG_BT_CTLR_ADV_DATA_LEN_MAX` Kconfig symbol, other controllers may
not have such Kconfig symbol. So this is a way for the host to be more
controller-agnostic and provide useful feedback to the users.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
In most cases these were defined as 1. Saving one byte for the rest
doesn't really justify the added complexity that comes with these
options. Removing them also simplifies the interface between HCI
transports/drivers and the host stack, which in turn helps pave the way
for having HCI as a proper Zephyr driver API.
Fixes#71907
Signed-off-by: Johan Hedberg <johan.hedberg@gmail.com>
