Changes signature so it takes uint32_t instead of pointer to a
register.
Later `sys_read*` and `sys_write*` functions are used, which cast
given address to volatile pointer anyway.
This required changing types of some fields in LiteX GPIO driver and
removal of two casts in clock control driver.
There was a weird assert from LiteX GPIO driver, which checked whether
size of first register in dts was a multiple of 4.
It didn't make much sense, so I removed it.
Previous dts was describing size of a register in terms of subregisters
used. New one uses size of register, so right now it is almost always
4 bytes.
Most drivers don't read register size from dts anyway, so only changes
had to be made in GPIO and clock control drivers.
Both use `litex_read` and `litex_write` to operate on `n`bytes.
Now GPIO driver calculates this `n` value in compile time from given
number of pins and stores it in `reg_size` field of config struct like
before.
Registe sizes in clock control driver are hardcoded, because they are
tied to LiteX wrapper anyway.
This makes it possible to have code, independent of CSR data width.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Adds LITEX_CSR_DATA_WIDTH option to Kconfig
Depending on its value appropriate read/write handling is used
for accessing CSR registers.
By using `>=` in preprocessor conditions it is somewhat future-proofed.
Doesn't touch `litex_read` and `litex_write` yet.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Do not assume `reg_size` to be a multiple of 4 and
divide it on each call, expect the caller to provide
an already divided value instead.
This change require the LiteX GPIO driver to be modified,
which will come in the following commit.
Signed-off-by: Pawel Czarnecki <pczarnecki@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
This adds a helper function for reading LiteX 64-bit CSRs
to be used by LiteX drivers.
Signed-off-by: Jakub Cebulski <jcebulski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
This commits adds GPIO driver for LiteX SoC builder.
Due to the fact that GPIO in LiteX is unidirectional and can be
configured with different pins amount per port, additional entries
were added to the dts file.
Signed-off-by: Robert Winkler <rwinkler@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
generated_dts_board.h is pretty redundant and confusing as a name. Call
it devicetree.h instead.
dts.h would be another option, but DTS stands for "devicetree source"
and is the source code format, so it's a bit confusing too.
The replacement was done by grepping for 'generated_dts_board' and
'GENERATED_DTS_BOARD'.
Two build diagram and input-output SVG files were updated as well, along
with misc. documentation.
hal_ti, mcuboot, and ci-tools updates are included too, in the west.yml
update.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Depending on LiteX configuration, CSRs
(control&status registers) might be split
into several consecutive registers.
This introduces common helper functions
for all LiteX drivers providing access
to CSRs for a default LiteX configuration
(data_width = 8bit, bus_width = 32bit).
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
With the upcoming riscv64 support, it is best to use "riscv" as the
subdirectory name and common symbols as riscv32 and riscv64 support
code is almost identical. Then later decide whether 32-bit or 64-bit
compilation is wanted.
Redirects for the web documentation are also included.
Then zephyrbot complained about this:
"
New files added that are not covered in CODEOWNERS:
dts/riscv/microsemi-miv.dtsi
dts/riscv/riscv32-fe310.dtsi
Please add one or more entries in the CODEOWNERS file to cover
those files
"
So I assigned them to those who created them. Feel free to readjust
as necessary.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
2019-08-02 13:54:48 -07:00
Renamed from soc/riscv32/litex-vexriscv/soc.h (Browse further)
