Define the reg and size property for the stm32 boards with qspi inside
Refer to the dts/bindings/flash_controller/st,stm32-ospi-nor.yaml.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Define the reg and size property for the stm32u585 and stm32l562
disco kit.
Refer to the dts/bindings/flash_controller/st,stm32-ospi-nor.yaml.
The stm32l562 reads the sfdp table from the flash itself.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
1. Configure 'core-clock' to 192MHz to generate necessary 48MHz
2. Support workaround to disallowing ISO IN/OUT EPs to be assigned
the same EP numbers
Signed-off-by: Chun-Chieh Li <ccli8@nuvoton.com>
drivers: eth: phy: tja1103: Handle link change
These changes enable -
TJA1103 driver to gracefully handle Link connect or disconnect events
between Ethernet PHY and its link partner and notify it to the
upper network layers
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
The DMA is already enabled for this board, but updating the board doc
page to make that clear, and enabling the DMA loop_transfer test.
Signed-off-by: Derek Snell <derek.snell@nxp.com>
GR716A has two SPIMCTRL SPI controllers.
This adds the SPIMCTRL description to the DTS and makes the SPI
option available in the kernel configuration.
Signed-off-by: Martin Åberg <martin.aberg@gaisler.com>
Add support for ADI EVAL-ADIN2111EBZ.
Tested samples:
* hello_world
* blinky
* dhcpv4_client
Co-developed-by: Philip Molloy <pmolloy@baylibre.com>
Signed-off-by: Philip Molloy <pmolloy@baylibre.com>
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Add support for ADI EVAL-ADIN1110EBZ.
Tested samples:
* hello_world
* blinky
* dhcpv4_client
* adt7420
Tested proper SPI detection of the ADIN1110 chip.
Co-developed-by: Philip Molloy <pmolloy@baylibre.com>
Signed-off-by: Philip Molloy <pmolloy@baylibre.com>
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Microchip's PolarFire SoC interface with on-board spi
nor flash via system controller. This on-board spi nor flash can be
used to store FPGA design bitstream's.
Signed-off-by: Harshit Agarwal <harshit.agarwal@microchip.com>
qemu_x86_tiny@768 has coverage enabled by default. Because of
this, it requires more stack space for running tests.
The increases needed are verified via twister.
Fixes#68272
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert ili9xxx display drivers to use MIPI DBI API. Due to the fact
this change requires a new devicetree structure for the display driver
to build, required devicetree changes are also included in this commit
for all boards and shields defining an instance of an ili9xxx display.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
add acpi pnp/hw id for pcie node to enable support for retreive
interrupt routing information for pci legacy interrupt via acpi
Signed-off-by: Najumon B.A <najumon.ba@intel.com>
We need to enable this configuration for all R-Car ARM64 boards.
First and foremost, we definitely should run Zephyr on the boards
in the NS-EL1 state. The EL3 is used for TF-A, EL2 is used for
U-Boot, and Xen in the case when we run Zephyr as Dom-0. The S-EL1
is used for OP-Tee, and S-EL0 is used for OP-Tee apps.
Signed-off-by: Mykola Kvach <mykola_kvach@epam.com>
On the Polarfire SOC Icicle Kit the SPI pins are routed to MikroBus.
Enable SPI by default.
Signed-off-by: Naga Sureshkumar Relli <nagasuresh.relli@microchip.com>
the device tree offers a default config (qdec0) for 1x qdec at TC0,
however does not offer a default config for qdec1 - qdec3.
this will be added with this commit. Fixes#65610
Signed-off-by: Sven Ginka <sven.ginka@gmail.com>
The purpose of this separation is to avoid conflict initializing
gpio-keys because button 0 and joystick up have a shared interrupt
source. Joystick is now configured using polling mode option.
Signed-off-by: Joel Guittet <joelguittet@gmail.com>
This allows to run tests & examples on the physical board with:
```
west twister -p mps2_an521 --device-testing --device-serial /dev/ttyUSB0
```
Signed-off-by: Wilfried Chauveau <wilfried.chauveau@arm.com>
Create a folder for RZ Renesas range device tree to follow how it's
done for other renesas ranges.
It will also help to better delimit areas to maintain.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
- Remove hadcoded cc2538-bsl.py path
- Use cc1352-flasher program instead
- Add docs about how to install the program
Signed-off-by: Ayush Singh <ayushdevel1325@gmail.com>
This commits makes it possible to use the onboard bluetooth
module (STM32WB5MMG) with existing zephyr bluetooth samples.
Note that there was no hardware flow control wiring
available on the board, which is why it has been disabled
in the both main board and BLE module Device Tree. As the
board doesn't support HW flow control, users must set
CONFIG_BT_HCI_ACL_FLOW_CONTROL=n in project files.
Signed-off-by: Javad Rahimipetroudi <javad.rahimipetroudi@mind.be>
This patch introduces the Bluetooth Low Energy (BLE) feature to the board.
The board utilizes the STM32WB5MMG as the BLE module. However, As there
was no BLE controller available for this module. Therefore, a board
support package has been added to enable the STM32WB5MMG module to act as
a BLE controller. This is achieved by running Zephyr's hci_uart example on
the STM32WB5MMG module which enables communication with the main
microcontroller over the H:4 HCI transport protocol. So, users must first
build the BLE controller for the BLE module and upload it via on board
ST-Link,then they can uses Zephyr Bluetooth demos on the development board
Note that there was no hardware flow control wiring available on the
board, which is why it has been disabled in the both main board and BLE
module Device Tree.
Signed-off-by: Javad Rahimipetroudi <javad.rahimipetroudi@mind.be>
OpenOCD can now be used to flash and debug nucleo_wba52cg.
However it required use of STMicroelectronics OpenOCD fork.
Add instructions on how to use it.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
This reverts commit 6a3612666e
"boards: mps2_an385: Exclude platform from networking tests"
This would have found the issue described in #67762 where a
network test was failing because of wrong section placement.
All the simulated environments (qemu_x86 and native_sim) used
in network testing missed this problem, but could have easily
found if network tests would have been run in mps2_an385.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Instead of relaying on those macros having been defined
somewhere else let's define them for this library.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This constant is supposed to be defined as a long instead of an int,
presumably to support systems where int isn't large enough.
Signed-off-by: Keith Packard <keithp@keithp.com>
Define the pinctrl-based pin controller instance
for the Mercury XU board and remove the old implementation
Signed-off-by: Jan Bylicki <jbylicki@antmicro.com>
Setting an extremely low value by default on two boards doesn't seem
like the right thing to do. The defaults were added with the v1 logging
subsystem in https://github.com/zephyrproject-rtos/zephyr/pull/8023.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Provide three basic examples to test the x-nucleo-iks4a1 shield:
- Test shield in standard mode
Acquire sensor data from shield with all MEMS sensors connected
to micro-controller
- Test shield in HUB1 mode
Acquire sensor data from shield with lis2mdl and lps22df
connected to LSM6DSV16X sensor hub
- Test shield in HUB2 mode
Acquire sensor data from shield with lis2mdl and lps22df
connected to LSm6DSO16IS sensor hub
Signed-off-by: Armando Visconti <armando.visconti@st.com>
x-nucleo-iks4a1 shield is an arduino compatible companion board
which can be used on top of Nucleo standard boards for industrial
applications. Following MEMS sensor are currently supported:
- LSM6DSO16IS: MEMS 3D accelerometer + 3D gyroscope
- LSM6DSV16X: MEMS 3D accelerometer + 3D gyroscope
- LIS2MDL: MEMS 3D magnetometer
- LPS22DF: Low-power and high-precision MEMS pressure sensor
(https://www.st.com/resource/en/data_brief/x-nucleo-iks4a1.pdf)
The board exports three overlays:
1. x_nucleo_iks4a1.overlay (standard mode)
All MEMS sensors are connected to micro-controller.
2. x_nucleo_iks4a1_shub1.overlay (HUB1 mode)
LSM6DSV16X IMU sensor act as a sensor_hub with LIS2MDL and
LPS22DF connected to it.
3. x_nucleo_iks4a1_shub2.overlay (HUB2 mode)
LSM6DSO16IS IMU sensor act as a sensor_hub with LIS2MDL and
LPS22DF connected to it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The nucleo_g0b1re board is based on stm32g0 that supports 2 can
controllers. This commit adds support for the second can controller.
Add also can label in yml board file.
Signed-off-by: Adrien MARTIN <adrienmar@kickmaker.net>
This patch add the basic board support for the
STM32WB5MM-DK Discovery Kit. At the moment only
debug UART Debug is ported. Other peripherals will be added
in the following patches.
Signed-off-by: Javad Rahimipetroudi <javad.rahimipetroudi@mind.be>
In order to build a BLE application nucleo_wba55cg fecthing controller
blobs is required. Document the command.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Let's not treat this driver differently for simulation
than for real HW.
There is a few cases which are not yet working,
but the driver is disabled by default for all platforms.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
CONFIG_RISCV_SOC_INTERRUPT_INIT=y and CONFIG_RISCV_HAS_PLIC=y are both
defaulted to y by the board SoC.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Decrease total RAM usage when Wi-Fi is enabled, specially after
`config HEAP_MEM_POOL_ADD_SIZE_BOARD` was added. This allows application
to handle additional HEAP as required.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
