The buffers for the PBP advertising data as well as the
buffers for the BASE periodic advertising data were
not cleared, so calling the functions multiple times
would simply append the data rather than just setting
the new data.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
There are devices that will send empty SDUs instead of
empty PDUs, and while that should be harmless, it is nice
to know what is going on, and we may want to deal with
empty SDUs and empty PDUs differently.
This also modifies the state for TS and PSN to only be
applied for valid ISO packets.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
It is a common occurance that a specific type is not
found in the codec configuration, and the main way of
knowing that is by calling the function.
The debug log does not help debug anything (as it does also
return a specific error code), but rather just clutters up
the log if enabled.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
When returning an error code directly to an application
in the API, it should not log as a warning or error.
The lack of PAC records is also reported directly to the
application, and is not an error (in fact it is valid not to have
e.g. sink or source pacs).
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add printing of the broadcast ID and whether an existing PA
sync was found in the bap_broadcast_assistant_recv_state_cb
function.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The bap_broadcast_assistant mod_src command can now take "unknown"
as a value to supply BT_BAP_PA_INTERVAL_UNKNOWN to the scan
delegator.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The documentation for the command
bap_broadcast_assistant broadcast_code
was incorrect and has been fixed.
Additionally, and example of the command has been added
in the shell documentation.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
When a PA is synced via PAST, the receive state does not
have a PA sync object, and the address and SID must be
used.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The audio configuration 5 is defined to have 2 sink channels
per stream and 1 source channel per stream.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Increase the supported receive state count to 4, as
several on-market device have at least 2 and sometimes
more.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
If pa_sync_past returns 0 then that means we are ready to
sync to past, and the BT_BAP_PA_STATE_INFO_REQ state should be set.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
stm32l1_disco board from STMicroelectronics has eeprom and watchdog.
Enable those peripherals.
Tested using:
1. samples/drivers/eeprom
2. samples/drivers/watchdog
Signed-off-by: Maxin John <maxin.john@gmail.com>
LPTIM4 is selected, since it is used only for internal timing
and it doesn't support output/input
Signed-off-by: Adam Berlinger <adam.berlinger@st.com>
The LL_APBx_GRPn_ReleaseReset clears reset bit in RCC,
however this bit is reset by default. Code that set
this bit was removed in previous commit
0856e99155
Keepint the autonomous clocks for STM32U5 family.
Signed-off-by: Adam Berlinger <adam.berlinger@st.com>
Magic constants throughout the code made this difficult to reason about,
especially with two different units of measurement (bytes and words) at
play.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
The RX FIFO size is in words, so needs to be subtracted from the total
memory size *after* it's divided by 4.
Fixes#70789.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
This adds DT aliases for LED and button used in recovery mode of the
MCUboot bootloader, on the 'nucleo_wb55rg' board.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Add nrfx_grtc related entries that were introduced in nrfx 3.4.0,
especially NRFX_GRTC_CONFIG_AUTOSTART that should be by default
set to 1.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This patch adds support for custom commands to be executed during the
build of an llext target. The commands can be executed at different
points in the build process:
- PRE_BUILD: Before the llext code is linked.
- POST_BUILD: After the llext code is built, but before packaging
it in an .llext file.
- POST_PKG: After the llext file has been created.
Note that PRE_BUILD is not supported for ARM targets, as in that case
object files are used directly and there is no actual linking step.
The commands can be added using the new add_llext_command() function.
An example usage of it, along with some target properties, is added to
the hello_world test case.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
Remove the C_FLAGS argument from add_llext_target() and add a set of
functions to configure the compilation and linking of an llext using
the same API of the target_* functions.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
This change reworks the Xtensa support in llext to use CMake's native
shared library support, instead of manually running "gcc -shared".
This change minimizes the differences in llext handling by defining
appropriate CMake targets for the different architectures.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
When CONFIG_LLEXT is enabled, the Zephyr platform needs to enable dynamic
library support. This is done by setting the `TARGET_SUPPORTS_SHARED_LIBS`
property to `TRUE` in the global property scope.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
Add entry for st7796s to display build_all test, so that the controller
driver will be built by CI.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add driver for ST7796s display. This is a MIPI DBI display controller,
with a frame memory of 320x480x18 pixels. Support for 4 wire SPI mode is
implemented using the MIPI DBI API.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add binding for sitronix ST7796s, a MIPI DBI display controller
supporting up to 320x480 displays at 18 BPP
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
