Add a fixed clock to the qemu-virt-a53.dtsi to match how the musca dts
files work so we get the clock DT info in the same way in the driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add interface name to link up/down information message
to help tracking which port is changing status.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
Copy paste error, base address of second controller was set to the
same as the first one, corrected to ENET2.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
With Ethernet controller base address is not straight forward
to figure out if it is ENET or ENET2l, using name is much better.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
This will allow having a different PHY address for each controller.
It also avoids for the PHY address to be hard-coded in several
functions.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
Add new config allowing to enable the second Ethernet port
on i.MX RT1060 SoC family.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
Source and destination ports should be set properly
when assembling the receive socket data.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
Coverity doesn't invoke the build for this module with a configuration
that provides a non-zero delay for entering or releasing deep power
down, so it sees a check that a value known to be non-negative
magically became negative without being touched, and so screams about
dead code.
Refactor to make the adjustments unconditional which has the same
effect in any reasonable level of optimization while making it
slightly less obvious that the value may not change.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add entropy driver based on GECKO TRNG module along with device
tree support for EFM32PG and EFR32MG SOCs.
Signed-off-by: Pooja Karanjekar <pooja.karanjekar@lemonbeat.com>
This reverts commit 8739517107.
Pull Request #23437 was merged by mistake with an invalid manifest.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This reverts commit 979ed4e1cd.
Pull Request #23437 was merged by mistake with an invalid manifest.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add a missing include of debug/stack.h in order to fix the
compilation warning on implicit declaration of log_stack_usage().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Reworked calibration to not use HW platform which is not available on
some platforms (nrf53) and does not bring any value compared to using
system timer. Switched to use k_timer. Additionally, improved
calibration algorithm to request also LF clock before starting
calibration. This simplifies the algorithm because it does not need
to support disabling low frequency clock which in calibration.
Tests has been updated and simplified. Former tests relied on HW timer
event.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This commit fixes the field definition names for `GICD_ICFGR`, which
were incorrectly prefixed with `GICC_`.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Change adds waiting until PWM is stopped before restarting it. Without
the change, calling the pwm_nrfx_pin_set function multiple times in
quick succession could cause a race condition causing the PWM to
remain stopped in case it should be restarted.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
The ISM330DHCX is a ultra-low power IMU with a 3D digital accelerometer
and 3D digital gyroscope tailored for Industry 4.0 applications, which
can be interfaced through either I2C or SPI bus.
https://www.st.com/resource/en/datasheet/ism330dhcx.pdf
This driver is based on stmemsc i/f v1.02.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
LPUART1 TX alternate function number for PB6 was not correct in the
pinmux settings for H7 series.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
With new NXP HAL, MCUX CSI does not necesseraly start the
capture into the first submitted buffer. However the driver
expects that buffers will be captured in submitted order.
Fix that.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
k_mem_pool_malloc reserves some space for block descriptor at the start
of the data block, causing misalignement of returned video buffer.
In our context we want to return a video buffer with aligment matching
the video buffer poll alignment config. Fix that by using the simpler
k_mem_pool_alloc function.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
After RX is disabled during receiving, some bytes are received to
internal fifo. To not interfere with further transactions fifo has to be
flushed.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Add Virtual LAN support to stm32 Ethernet driver. Refactor the
eth_iface_init() and move device configuration settings to
eth_initialize() as the eth_iface_init() is called multiple
times (once / configured VLAN).
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Towards cleaning up (and hopefully removing dts_fixup.h in the near
future). We need to move the handling of different names for the irq
flag propety into the driver and out of dts_fixup.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Towards cleaning up (and hopefully removing dts_fixup.h in the near
future). We need to move the handling of different names for the irq
flag propety into the driver and out of dts_fixup.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch is setting the pin to very high speed for all
the SPI2 clock outputs, for the stm32f7 soc series.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Convert usb_stm32 driver to use of DT_INST macros.
Since driver is compatible with 3 different dt compatibles and
compatible string is included in DT_INST macros, I've kept the
DT_USB_ compatible agnostic macros based on DT_INST ones, which
allowed to remove fixup definitions.
Use of DT_USB symbols is now limited to usb_dc_stm32.
Additionally, compatible "st,stm32-otgfs" is removed from list
of compatibles for usbotg_hs ips.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use DT_INST_ defines.
In the process, we've removed all UART/USART/LPUART code in
device instanciation code which had no impact.
Since all uart/usart/lpuart nodes declare compatibility with
st,stm32uart, DT_INST_X_ST_STM32_UART_FOO could be used.
Removed DT_UART fixup macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On stm32 spi devices, there are 2 main IP variants, with and w/o
fifo. Fifo is not really used today, but still there is some
additional code handling fifo. Today this code is protected under
Kconfig symbol SPI_STM32_HAS_FIFO.
This code carries redundant information vs dedicated compatible
"st,stm32-spi-fifo", which is provided as unique driver compatible
for devices supporting this IP as opposed to use of "st,stm32-spi"
when fifo is not supported.
Having these 2 compatibles defined exclusively is not convenient for
migration to DT_INST as DT_INST macros contain compatible string and
hence it cannot be used to provide common compatible code for devices
defining different compatibles.
Based on these observations, review stm32 spi devices compatible
declarations. Devices supporting fifo will now declare both
compatibles, as proposed by dt spec: "[compatible] property value
consists of a concatenated list of null terminated strings,
from most specific to most general". Hence field will now be:
"st,stm32-spi-fifo", "st,stm32-spi"
This way, fifo enabled stm32 spi devices will generate both:
DT_INST_STM32_SPI_FOO and DT_INST_STM32_SPI_FIFO_FOO
As well as:
DT_COMPAT_ST_STM32_SPI and DT_COMPAT_ST_STM32_SPI_FIFO
So, DT_INST_STM32_SPI_FOO could be used for device initialization.
Also DT_COMPAT_ST_STM32_SPI_FIFO could be used for FIFO handling
code inside driver. Hence use it to replace Kconfig symbol
SPI_STM32_HAS_FIFO.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use DT_INST_ defines.
Removed DT_FLASH_DEV fixup macros, except DT_FLASH_DEV_NAME
used in applications.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use DT_INST_ defines.
Removed DT_RTC_0 fixup macros but keep DT_RTC_NAME_0 as it is
still in use across RTC users.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The RX fragment debug print does not work (compile error)
if memory allocation debugging is enabled, so disable it
for time being.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In the DT_INST conversion we introduced a typo bug of accessing port0
instead of port1 in the IRQ config function.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Configure the PWM period and pulse width in timer ticks instead of
calculating the frequency and duty cycle for use in the higher level
MCUX API. This improves the resolution of the PWM output signal
considerably.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The IIS2DLPC is a 3D digital accelerometer ultra-low power sensor
for industrial applications, which can be interfaced through either
I2C or SPI bus.
https://www.st.com/resource/en/datasheet/iis2dlpc.pdf
This driver is based on stmemsc i/f v1.02
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Telnet console was move as a shell backend and is not anymore part of
console drivers.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Enable counter driver support for H7 series. Tested with H743ZI MCU
using samples/drivers/counter/alarm.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
