Of these, only struct net_ipv6_nbr_data::send_ns is a descriptive
change:
send_ns is used for timing Neighbor Solicitations in general, not
just for DAD.
The rest are typo/grammar fixes.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The PIO cores on Altera Nios-II processors can be used
for GPIOs and each PIO core can be configured as Input only,
Output only or as Bidirectional port from the Qsys tool.
The present Nios-II softcpu image on the Zephyr only has the
support for Output only port and the PIOs[0:3] are wired to
LED[0:3] on the Altera MAX10 board.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
In ARC's SecureShield, a new secure mode (currently only em) is added.
The secure/normal mode is orthogonal to kernel/user mode. The
differences between secure mode and normal mode are following:
* different irq stack frame. so need to change the definition of
_irq_stack_frame, assembly code.
* new aux regs, e.g, secure status(SEC_STAT), secure vector base
(VECT_BASE_S)
* interrupts and exceptions, secure mode has its own vector base;
interrupt can be configured as secure or normal through the
interrupt priority aux reg.
* secure timers. Two secure timers (secure timer 0 and timer 1) are
added.Here, for simplicity and backwards compatibility original
internal timers (timer 0 and timer1) are used as sys clock of zephyr
* on reset, the processor is in secure mode and secure vector base is
used.
Note: the mix of secure and normal mode is not supported, i.e. it's
assumed that the processor is always in secure mode.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Some drivers doesn't implement flash API page layout extension
which is causing the application crash once the API was calling.
This patch introduce system termination for this in those drivers
which doesn't implement extension. This will help to discover this
problem early.
It is not done by preprocessor check because it is possible to have
enabled a driver which support and a driver which doesn't support
this API simultaneously.
Now FLASH_PAGE_LAYOUT configuration option is accessible only in case
that at last one driver which implements mentioned API is enabled.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
On stm32f3_disco pins PF0/PF1 are used for OSC_IN/OSC_OUT
signals. Use pins PA9/PA10 for I2C_2 port
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Add the STM32F0 Embedded Flash support in the flash_stm32 driver
interface.
The STM32F0 has a particularity or use the HSI as clock source
for the flash controller interface, so this clock must be
enabled directly in the case HSE or another clock is used by
the system clock.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
IPv6 mcast addr to MAC mcast conversion was factored out to
subsys/net/ip/l2/ethernet.c for reuse by other drivers.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Now that proper solicited-node multicast group joing is implemented,
promiscuous mode's purpose is reduced to just debugging needs.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This fixes a regression from
https://github.com/zephyrproject-rtos/zephyr/pull/5018
The ieee802154 driver wouldn't build because nrf drivers/ieee802154
depends on the nordic ext drivers to build.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Fix#5298
irq_is_pending function returned TXE/RXNE flag status
even if IRQ was masked, which led to enless loop
in uart_pipe when no TX was performed. Fix by reporting status only when
IRQ is unmasked.
Signed-Off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In uart_nrf5.c the IRQ masks for the TX READY and ERROR events are
incorrect. This pull request fixes the mask values so they are
according to the nRF51/nRF52832/nRF52840 product specification.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Added Inter-IC Sound driver (based on SSC module) for Atmel
SAM MCU family.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-2509
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added DMA (XDMAC) driver for Atmel SAM MCU family. The driver provides
private DMA API to be used by the SAM family device drivers. Public
DMA API to be used by user space programs is currently missing.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1609
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This patch makes minor improvements to the flash documentation:
* spi -> SPI
* Capitialise the first word in a sentance
* Adding the, and, all, etc where appropriate.
Signed-off-by: Michael Hope <mlhx@google.com>
Waiting for transfer complete and stop condition uses while loops
even when interrupt mode is enabled.
Implement use of TC, TCR and STOP interrupt for interrupt mode.
msg_done is not needed in interrupt mode anymore, so move it
to non-interrupt section
Tested with stm32f3_disco board.
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
Disabling of Interrupts is duplicated. Move it to a position
that is common to messages that end with and without errors.
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
As the nRF5x BLE controller uses TIMER1, TIMER2 and PPI
indices 0-13 (and 14-15, if PA/LNA feature is enabled),
the software based PWM driver needing 6 PPI channels has
to use PPI indices outside the BLE controller used range.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
- Renaming NET_L2_RAW_CHANNEL to NET_RAW_MODE
- Create a generic IEEE 802.15.4 raw mode for drivers
- Modify the IEEE 802.15.4 drivers so it passes the packet unmodified,
up to code using that mode to apply the necessary changes on the
received net_pkt according to their needs
- Modify wpanusb/wpan_serial relevantly
Fixes#5004
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Delete the native UART JTAG driver as we will be reusing
the Altera's HAL driver.
Add the shim driver support for Altera HAL's JTAG UART soft IP.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Delete the native timer soft IP driver as we will be reusing
the Altera's HAL drivers for most of the soft IP's.
Add shim driver support for Altera timer system clock soft IP.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Rename the Atmel SAM I2C driver based on TWIHS module to match the
convention:
<driver class>_<SoC family>_<hardware module used by the driver>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Various minor changes to the Atmel SAM (TWIHS) driver
- clean up variable names, comments
- refactor i2c_clk_set function
- do not save configuration in dev_data
- improve ISR NACK handling
- print "Device initialized" string
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Adds a new gpio driver for the NXP i.MX family of SoCs. Read, write,
configure, and callback API functions are all implemented.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Event ISR checks if the TX/RX interrupts is enabled instead
of the TXIS/RXNE interrupt status flags. Use the TXIS/RXNE
interrupt status flags to check which interrupt event
happened.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
STM32 I2C driver doesn't use the I2C API flags STOP/RESTART,
instead it uses its own RESTART flag. As a result, I2C API's
i2c_burst_write* funtions doesn't work. This patch makes
STM32 I2C driver to use I2C API flags.
Tested on: 96b_carbon, olimexino_stm32 (i2c_ll_stm32_v1)
Tested on: stm32f3_disco, disco_l475_iot1 (i2c_ll_stm32_v2)
Fixes: #4459
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
The interrupt priority on KW41Z is from 0..3. The value of 0x80 is
invalid, so lets set it to 0 for now as all the other interrupt
priorities default to 0 right now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added conditionally enabled event state tracing support.
Needed for enhanced debug visibility of tight timed events where
normal print debug messages affect the timing of things. This is a
simple buffer that allows post analysis via gdb of what sequencer
events occurred.
Signed-off-by: David Leach <david.leach@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
