Add a basic connection test between two devices,
in which the controllers are in separate nrf52_bsim devices
connected over UART to the devices running the host+app.
The controllers are running the HCI UART async sample.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This is a follow-up to commit c7e4d23c5d.
After all calls to `nrfx_dppi_*` and `nrfx_ppi_*` functions were
replaced with corresponding `nrfx_gppi_*` calls, it is no longer
needed to include the `nrfx_dppi.h` and `nrfx_ppi.h` headers.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The sample needs to check in Kconfig whether PPI or DPPI is present
on the target platform in order to enable the proper allocator in nrfx.
It should not use the `HAS_HW_NRF_*` symbols for this as those take
into account also the status of the corresponding DT node, not only
its presence.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This sample makes calls to the nrfx_gpiote driver functions that
require absolute pin numbers, not relative to a given GPIO port,
so instead of getting the numbers with the `DT_GPIO_PIN` macro,
it should use `NRF_DT_GPIOS_TO_PSEL`.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert the sample for the lmp90100_evb shield to use devicetree for
configuring the ADC channel.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
If accept() returns an error, it typically means that the
system is running out of resources. In this case sleep
some time in order the system to cool down a bit.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If accept() returns an error, it typically means that the
system is running out of resources. In this case sleep
some time in order the system to cool down a bit.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
PBP API allows sources to create a Public Broadcast Announcement.
PBP API to parse a Public Broadcast Announcement.
public_broadcast_source application starts extended advertising and
includes a Public Broadcast Announcement. The advertised broadcast
audio stream quality will cycle between high and standard quality.
public_broadcast_sink application scans for broadcast sources and
synchronizes to the first found source which defines a Public Broadcast
Announcement including a High Quality Public Broadcast Audio Stream
configuration.
Add bsim tests for Public Broadcast Profile APIs.
Add shell implementation for Public Broadcast Profile APIs.
Signed-off-by: Daniela Andreea Dumitrache <danielaandreea.dumitrache@nxp.com>
Physical boards work on these tests but some of the required
peripherals are not simulated by `renode`, executing the tests
with renode-simulated board in CI will fail.
Exclude `renode` simulation from these tests.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Updated API version enables multi-instance GPIOTE driver.
Additionally obsolete symbol that was used to specify
API version in the past was removed.
Affected drivers have been adjusted and appropriate changes
in affected files have been made.
Signed-off-by: Jakub Zymelka <jakub.zymelka@nordicsemi.no>
The incorrect semaphore was used for the ipc1 instance to synchronise
the data receiving.
This commit fixes it.
Signed-off-by: Marcin Jelinski <marcin.jelinski@nordicsemi.no>
Adjust the sample to work with the priority boost. It illustrates zbus
being used inside an ISR instead of into the main function.
Signed-off-by: Rodrigo Peixoto <rodrigopex@gmail.com>
This change follow the recent commit that update openamp rsc table logs.
Add the logs for both samples sample client & TTY responder,
as well as for both sides Linux & Zephyr.
Remove the serial connection to Zephyr because it is board specific.
Signed-off-by: Marc-Antoine Riou <marc-antoine.riou@iot.bzh>
Add logs in both of the openamp rsc table loops to stick with
what is shown in Zephyr documentation. Prefix each message with the loop
name and unify logs with those from rpmsg_client_sample module.
Signed-off-by: Marc-Antoine Riou <marc-antoine.riou@iot.bzh>
Sample openamp_rsc_table was sending too many characters to master.
It was displayed as unrecognised character when reading message on master.
Signed-off-by: Marc-Antoine Riou <marc-antoine.riou@iot.bzh>
The sample did not correctly select the WinUSB
driver for the WebUSB interface as required
on Windows when CDC ACM was included in the
build configuration (the case for e.g. nRF52840
Dongle).
Introduce correct function subset header in the
MS OS 2.0 descriptor.
Signed-off-by: Lars Knudsen <larsgk@gmail.com>
Allow engine to give hints about ongoing CoAP transmissions.
This information can be used to control various power saving
modes for network interfaces. For example cellular networks might
support release assist indicator.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Add DT overlay to be able to support and test UDC DWC2 driver
(snps,dwc2) on nucleo_f413zh board. This disables STM32 shim
driver described and configured on the SoC and board level.
Obviously,it should work with other STM32F4 boards as well and we
could have a mechanism to apply it generically using snippets.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Update coap_service_send and coap_resource_send to take an optional
pointer argument to the newly introduced coap_transmission_parameters.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
This is just as arbitrary as what was before, but simpler.
Before this change, the callback were invoked upon receiving the num
complete packets event.
This did not necessarily work with all spec-compliant controllers.
Now the callback is invoked as soon as the lower layer destroys the
buffer. ATT shouldn't care whether L2CAP sends it over RFC1149 or
something else after that point.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
Co-authored-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
Why?
- metadata is easier to manage as an array + index
- less error-prone -> less memory-management bugs
- we can. because of the previous refactor
- PDU allocations are more predictable
- ATT buffer size can be optimized by app
- isolates ATT from the rest of the ACL users
- decouples ATT PDU size from e.g. SMP w/ LESC
Drawbacks:
- higher memory usage
- kconfig change
The higher memory use is only temporary, as this will be followed-up
with more refactors that should bring it back down.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
Co-authored-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
Add README.rst file with description of sample which shows how to use
pytest and Twister together.
Signed-off-by: Piotr Golyzniak <piotr.golyzniak@nordicsemi.no>
Use the common USBD sample initialization helper where new USB device
support has already been added.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
There is common code for the new USB device support in the samples to
instantiate USB device, descriptors, configuration and initialize USB
device. Add common code that can be used for the simple usecase with a
single USB device and single configuration.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Renames "prov device" references and options to
"provisionee" to align implementation with Mesh
Protocol specification v1.1, section 5.4.
Signed-off-by: Anders Storrø <anders.storro@nordicsemi.no>
Adds a charge_enable handler to facilitate enabling and disabling
a charge cycle. This deprecates enabling and disable the charge
cycle via the CHARGER_PROP_STATUS property.
Signed-off-by: Ricardo Rivera-Matos <ricardo.rivera-matos@cirrus.com>
Updaye buffer counts and semaphore initial value so that the
Broadcast Audio Source can utilize any use of broadcast
pre-transmissions.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The issue with non secure storage system has been fixed
in nrf53_ns platform: https://github.com/zephyrproject-rtos/zephyr/issues/59376
No need workarounds anymore.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
The benchmark sample did not contemplate message subscribers. It adds
the msg subscribers and improves the organization of the project.
Signed-off-by: Rodrigo Peixoto <rodrigopex@gmail.com>
The subsys/logging/logger example can be used to demonstrate how to
use SWO for logging. Add a configuration fragment that enables the
logger's SWO backend. The default SWO frequency in this example is set
to 2 MHz to ensure a well-defined output bit rate instead of the
highest possible.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Set the prescaler for the stm32_lp_tick_source lptim node.
When the LPTIM is clocked by the LSE with a prescaler
of 16 (lptim freq at 2048Hz) expecting 2048 for the TICKS_PER_SEC.
When the LPTIM is clocked by the LSE with a prescaler
of 32 (lptim freq at 1024Hz) expecting 1024 for the TICKS_PER_SEC.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
