The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Instead of endlessly repeating the same command line args,
centralize this and tune the shift value on a per-board
basis.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Conditionalizes pinmuxes on associated driver configs (CONFIG_SERIAL,
CONFIG_I2C, etc.) for the rv32m1_vega board to avoid possible conflicts
between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add an additional check for CONFIG_PWM to decide if pins associated with
LED are configured for GPIO or PWM.
Fixes#25337
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enable icount mode for hifive1 platform, The icount shift value is
selectd based on cpu clock frequency of this platform. The virtual
cpu will execute one instruction every 2^shift ns of virtual time.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Enable icount mode for qemu_riscv64 platform, The icount shift value
is selectd based on cpu clock frequency of this platform. The virtual
cpu will execute one instruction every 2^shift ns of virtual time.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Enable icount mode for qemu_riscv32 platform, The icount shift value
is selectd based on cpu clock frequency of this platform. The virtual
cpu will execute one instruction every 2^shift ns of virtual time.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace DT_ALIAS_GPIO_x_LABEL with DT_NODELABEL references to get the
device name for the gpio ports.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds the selection of the necessary CONFIG_*
options for allowing the use of privacy on VEGA platform
Signed-off-by: Jeanina Dragusin <ancajeanina.dragusin@nxp.com>
The radio on the VEGA platform will now be able to resolve Resolvable
Private Addresses through the use of the CAUv3 hardware. With this
patch the RPA feature is now fully supported on the Controller:
RPA addresses are generated with local IRK and resolved with
previously exchanged peer IRK.
Signed-off-by: Jeanina Dragusin <ancajeanina.dragusin@nxp.com>
Per instance Kconfig symbols aren't used by the rv32m1 lpspi driver
so remove the unnecessary setting of PWM_2.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Updated the openisa,rv32m1_vega-pinmux binding to require the label
property and updated the rv32m1.dtsi to add label properties for the
pinmux nodes.
Also update gpio_basic_api test to use DT_NODELABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move board pinmux.c code to utilize
DT_NODELABEL instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move soc.c code to utilize DT_NODELABEL
instead.
Also rename various node labels to match the SoC docs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Point to zephyr/sdk release pages instead of non-existent downloads page
on project website.
Fixes#21706
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Now the VEGABoard BLE support includes the support for
the 2 Mbps BLE PHY, so the docs need to be updated
accordingly.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Created unit tests for the encryption and decryption functions.
Tested with the peripheral and with central_hr samples.
Due to latency of CAUv3 when used as CCM inline accelerator
only one of the PDU can be encrypted/decrypted within an
bilateral exchange M->S + S->M in a connection event.
If the RXed PDU is encrypted, the TXed PDU must be empty
with More Data if there is data in the LLL queue.
The TXed PDU will be encrypted when an empty PDU is RXed.
Signed-off-by: Cristi Caciuloiu <cristian.caciuloiu@nxp.com>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All board defconfig files currently set the architecture in addition to
the board and the SoC, by setting e.g. CONFIG_ARM=y. This spams up
defconfig files.
CONFIG_<arch> symbols currently being set in configuration files also
means that they are configurable (can be changed in menuconfig and in
configuration files), even though changing the architecture won't work,
since other things get set from -DBOARD=<board>. Many boards also allow
changing the architecture symbols independently from the SoC symbols,
which doesn't make sense.
Get rid of all assignments to CONFIG_<arch> symbols and clean up the
relationships between symbols and the configuration interface, like
this:
1. Remove the choice with the CONFIG_<arch> symbols in arch/Kconfig and
turn the CONFIG_<arch> symbols into invisible
(promptless/nonconfigurable) symbols instead.
Getting rid of the choice allows the symbols to be 'select'ed (choice
symbols don't support 'select').
2. Select the right CONFIG_<arch> symbol from the SOC_SERIES_* symbols.
This makes sense since you know the architecture if you know the SoC.
Put the select on the SOC_* symbol instead for boards that don't have
a SOC_SERIES_*.
3. Remove all assignments to CONFIG_<arch> symbols. The assignments
would generate errors now, since the symbols are promptless.
The change was done by grepping for assignments to CONFIG_<arch>
symbols, finding the SOC_SERIES_* (or SOC_*) symbol being set in the
same defconfig file, and putting a 'select' on it instead.
See
https://github.com/ulfalizer/zephyr/commits/hide-arch-syms-unsquashed
for a split-up version of this commit, which will make it easier to see
how stuff was done. This needs to go in as one commit though.
This change is safer than it might seem re. outstanding PRs, because any
assignment to CONFIG_<arch> symbols generates an error now, making
outdated stuff easy to catch.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Converts the fxos8700 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on frdm_k64f and rv32m1_vega_ri5cy boards. The latter verifies
that the reset output works correctly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Updates the rv32m1 gpio driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Assumes the gpio api layer handles translating logical flags to physical
flags.
Stops quietly reconfiguring pinmuxes to gpio mode. The pinmux must now
be configured explicitly in the board's pinmux.c or in the application.
Tested with:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_api_1pin
On boards:
- rv32m1_vega_ri5cy
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This enables LiteX PRBS random number generator driver
for litex_vexriscv board.
Signed-off-by: Pawel Czarnecki <pczarnecki@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Edited the index.rst file to say spi functionality is included. Also
edited the .yaml file in the boards directory to support spi for sanity
tests.
Signed-off-by: Jose Manuel Pacheco Luna <manuel.pacheco@nxp.com>
Added in enablement for the SPI-0 instance pins, as found in the
board schematic files. These connect to the arduino headers on the
front of the board.
Signed-off-by: Jose Manuel Pacheco Luna <manuel.pacheco@nxp.com>
64BIT has no prompt. Assignments in configuration files have no effect
on symbols without prompts. A prompt means the symbol is
user-configurable.
64BIT is instead enabled indirectly through being selected by
BOARD_QEMU_RISCV64, which is enabled in the same configuration file.
Detected through some work-in-progress improved error checking.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The HiFive1 boards power up using a 32 KiHz low frequency kernel, so
have a cycle rate of 32768 Hz. The board definitions have not been
revisited since the Zephyr default for ticks-per-second increased from
100 to 10000. The timer system on the board does not operate
correctly at 4 cycles per tick, but does at 328 cycles per tick.
To support functional timers while keeping system milliseconds in sync
with clock time set ticks-per-second to 128.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
