Adds support for the PGOOD pin. This pin is asserted by the
regulator when converter startup has completed and the output
is stable. If the PGOOD pin is not used, the PGOOD state is
check via the PGOOD_PIN_STS bit.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Enables the converter via I2C as the else case when the EN pin
conditional fails. This used to not matter as no code followed,
but this will change in subsequent patches.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Example of usage of HCI vendor specific Set Scan Request Reports
command, Scan Request Received Event and corresponding callback
to get application events. The sample application shows usage as an
alternative to extended advertisent saving precious RAM.
Signed-off-by: Giancarlo Stasi <giancarlo.stasi.co@gmail.com>
Ignore failure to Broadcast ISO remove data path when
terminating a BIG without a data path being setup.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When multiple advertisers overlap over time, the random
delay being applied need many ticker operation context.
This causes the ticker_update interface to return error
causing assertion in the Controller.
This is fixed by not applying random_delay value to the
overlapping advertiser that does not get to use the radio.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This reverts commit 9b43fed10a.
This PR introduced 2 regressions in main CI:
71977 & 71978
Let's revert it by now to get main's CI passing again.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This reverts commit 93dc7e7438.
This PR introduced 2 regressions in main CI:
71977 & 71978
Let's revert it by now to get main's CI passing again.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This reverts commit 61c70626a5.
This PR introduced 2 regressions in main CI:
71977 & 71978
Let's revert it by now to get main's CI passing again.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This reverts commit 3ef282be6c.
This PR introduced 2 regressions in main CI:
71977 & 71978
Let's revert it by now to get main's CI passing again.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This reverts commit 9f4d9989c6.
This PR introduced 2 regressions in main CI:
71977 & 71978
Let's revert it by now to get main's CI passing again.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This reverts commit 20611f13ca.
This PR introduced 2 regressions in main CI:
71977 & 71978
Let's revert it by now to get main's CI passing again.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This reverts commit 02b24911f7.
This PR introduced 2 regressions in main CI:
71977 & 71978
Let's revert it by now to get main's CI passing again.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
With the deprecation of `BT_LE_ADV_OPT_USE_NAME` and
`BT_LE_ADV_OPT_FORCE_NAME_IN_AD` samples were updated to not use the
macro adding the device name in the advertising/scan response data
anymore.
Instead the name was explicitly added to the scan response data in
`periodic_adv` sample. But because it was using an extended advertiser
and was already adding data in the AD, the name should have been put in
the advertising data and not the scan response data.
Update the sample to add the device name in the advertising data.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
With the deprecation of `BT_LE_ADV_OPT_USE_NAME` and
`BT_LE_ADV_OPT_FORCE_NAME_IN_AD` the tester has been updated to not use
the macro adding the device name in the advertising/scan response data
anymore. Instead the name was explicitly added to the scan response
data. But because that part of the tester was using an extended
advertiser and was already adding data in the AD, the name should have
been put in the advertising data and not the scan response data.
The same issue apply to both `btp_cap.c` and `btp_bap_broadcast.c`,
update them to add the device name in the advertising data.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
* Rename w5500_hw_reset to w5500_soft_reset.
This function performs a software reset, the GPIO reset is
hardware reset.
* Set thread name "eth_w5500".
* Simplify random MAC address code.
Remove unnecessary function pointer and wrapper function.
* Remove SPI read variable length array.
The VLA causes unnecessary stack usage and its max size changes
depending on CONFIG_NET_BUF_DATA_SIZE.
Split the SPI read into two transactions, a skip of the first 3
dummy bytes, then a read of the data directly into to given buffer.
* Remove unused variables config_func and full_duplex.
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
For many of the state checks with timeout, the check
should be very fast (sub 1 microseconds) and the
previous implemention involving busy waits between
checks could add unneeded latency. Change the
timeout checking method to use WAIT_FOR(), with
no extra delays between checks.
Signed-off-by: Mike J. Chen <mjchen@google.com>
Deprecate the use of location_* properties in the i2c_gecko driver
and migrate to the pinctrl api for enhanced maintainability and
compliance with current standards.
Signed-off-by: Arunmani Alagarsamy <arunmani.a@capgemini.com>
This update integrates I2C support with the pinctrl_configure_pins api
within the pinctrl_gecko driver.
Signed-off-by: Arunmani Alagarsamy <arunmani.a@capgemini.com>
Add overlay, for nrf52840dk, that reserves RAM in internal
SRAM using the DTS definition.
The sample with such region can be built with the config
file nrf52840dk_nrf52840_ram_disk_region.conf, but, instead
of automatically allocating memory, the Disk driver will
use the pre-defined region provided by the DTS overlay.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Add configuration for nrf52840dk that allows to create RAM
disk; this configuration does not reserve special region
in RAM using DTS but uses automatic buffer allocation, by RAM
Disk Drivers, according to RAM disk specification in DTS.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Enable serial communication through UART port between HDMI ports.
Signed-off-by: Myeonghyeon Park <myeonghyeon@tsnlab.com>
Signed-off-by: Junho Lee <junho@tsnlab.com>
Add support for Raspberry Pi 5.
Currently only internal GPIO(gio_aon) is supported.
'Blinky' is the only sample that is working for now.
Signed-off-by: Junho Lee <junho@tsnlab.com>
This enhances the description of i.MX8MPlus SoC with the Cadence HIFI4
core and thus will make this example more relevant to the benefits of
HWMv2.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Align the SPI init priority with other devices.
Other bus-devices like UART and I2C are init at standard kernel
device level (50), but SPI is at 70 and there appears to not be
a reason for it.
GPIO is init at 40 so there should not be an issue to use the default.
Signed-off-by: Joakim Andersson <joerchan@gmail.com>
Add support for a "pm" shell command to trigger suspend/resume as well
as runtime-get/put on devices. This is useful for testing during driver
development.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This property will ensure that PWM driver allocates data buffer
in appropriate location.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Some devices (like nRF54H20) must have PWM data buffer
stored in appropriate location.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
This property will allow PWM driver allocate data buffer
in appropriate memory region.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
For some hardwares, it is very common that some aligment on the allocated
memory is required. For example, the PxP and eLCDIF of NXP require aligned
buffers so that their performances can be optimal.
Add a new video_buffer_aligned_alloc() API for these needs.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Non-secure images cannot reference NRF_RRAMC_NS because NRF_RRAMC_NS
does not exist.
TF-M will configure RRAMC according to these Kconfig's before booting
the non-secure image so we ifdef out this code.
Also, rewrite the implementation of commit_changes to also work when
the commit task is not available.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
In the follow expression:
cyc_evt += UINT32_MAX + 1U
first it is evaluated (UINT32_MAX + 1U), since both types
interpreted as uint32_t, this operation causes an overflow resulting
in 0U.Then we have
cyc_evt = (uint64_t)cyc_evt + 0U
Fix it casting of the operands in the first operation to uint64_t.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Marking sysworkq as essential, so when it fails, the system will halt
instead of continuously working, and dependent components stay
in a broken state.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
Allow the creator of a work_queue instance to choose whether
the work_queue thread should be marked as ESSENTIAL or not.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
