Unlike stated in 57df225b396e43358aac4cc998ed2e99fdb57780, RM0456.pdf
reference manual mentions about PLL1R that "Only division by 1 and even
division factors are allowed."
Though, in reference manual, there is one issue on PLL1R values
description, which should actually be:
0000000: pll1_r_ck = vco1_ck
0000001: pll1_r_ck = vco1_ck / 2 (default after reset)
0000010: Not allowed
0000011: pll1_r_ck = vco1_ck / 4
...
This description will be fixed.
Reflect this in binding and driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This configuration does not work on some variants (simulator), reduce
the number to something that work on all variants.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Instead of enabling WOVCRO clock based on the SOC, use a configuration
to indicate support, so that each platform can specify if WOVCRO is
supported or not.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Add system clock control device (sysclk), so that the drivers can turn
on/off its clock through the clock control API.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Add binding for Aspeed AST10x0 clock driver. The clocks can be turned
on or off through the syscon registers.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
The stm32f303x8 SoC is not equipped with spi2 and spi3 peripherals.
Exclude them from the SoC-level devicetree.
Signed-off-by: Jan Kuliga <jtkuliga@gmail.com>
Add the octospi nodes to the stm32h7A3 and
and h7B0/h7B3 devices.
Note that RM0455 gives a size of 1kB.
The definition of the octospi clock source for both intances
is given by the DTS node. The selected value for
the alternate clock control is the PLL1_Q.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add the octospi nodes to the stm32h723/h725
and h730/h733/h735 devices.
Note that RM0468 gives a size of 1kB.
The definition of the octospi clock source for both intances
is given by the DTS node. The selected value for
the alternate clock control is the PLL1_Q.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The UC8176 and UC8179 chips that exist in tree have subtly different
register layouts. Use separate compatible strings for these chips and
a quirks structure that describe device-specific behavior.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
The GD7965 driver is really just a vendor name for the UltraChip
UC8179. Rename the driver to UC81xx since there are other chips in the
family (e.g., the UC8176) with an almost identical register interface.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
For the !SOC_I2C_SUPPORT_HW_CLR_BUS in which we implement bus
reset via GPIOs, change the devicetree properties to be actual
gpio properties and update the code to reflect this.
Signed-off-by: Kumar Gala <galak@kernel.org>
This commit adds the pll2 and pll3 clock control nodes
with st,stm32u5-pll-clock compatible.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit changes the range for stm32u5 pll divider values
to allow divider value of 1.
- DIVQ is allowed to beconfigured 1 for all PLL instances
- DIVR can be 1 for PLL2 and PLL3, but is not valid for PLl1.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
We have drivers for "nxp,lpc-rtc" and "zephyr,native-posix-counter"
devicetree compatibles, however we had no bindings for them. Add
simple bindings
Signed-off-by: Kumar Gala <galak@kernel.org>
Two files ending with yml while the rest is ending with yaml, just
rename those two to avoid special handling.
Fixes documentation build.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This CL adds a DT node, 'power_leakage_io', which property,
'leak-gpios', contains GPIOs that have leakage current. In oerder to get
better power consumption, npcx power driver will disable the connections
between these io pads and input buffers before entering deep sleep.
Then, restore the connections after ec wakes up.
The users can overwrite this property at board DT file. Here is an
example:
&power_leakage_io {
leak-gpios = <&gpio0 0 0
&gpiob 1 0>;
};
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL configures low-voltage (1.8V) detection via GPIO driver with
GPIO_VOLTAGE_1P8 flag. It also adds support for this flag in
pin_get_config() function.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Cleanup npcx low-voltage (1.8V) detection configuration. It removes
unused soc utilities, macros, and DT node. We will configure this
feature by GPIO driver with GPIO_VOLTAGE_1P8 flag later.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
ITE EC chip it81202 and it81302 both have embedded integrated
pd module (support two usbpd ports), this is different from
standalone TCPC. To prevent cc pins leakage, we disable not
active ITE USBPD port cc modules, then cc pins can be used
as gpio if needed.
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
Move the RX (MISO) delaying capability information to Devicetree. It is
done using 2 properties:
- rx-delay-supported: enabled on SPI nodes that support delaying RX.
This property can be used by the driver to determine if this
capability is supported or not on a given instance.
- rx-delay: the actual RX delay value
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Specify the overrun character in Devicetree. Since 0xFF is the most
common value, DT property contains such default.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Devicetree is the natural place to describe hardware, so move the
maximum frequency the SPI can work with to Devicetree instead of relying
on values from HAL.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Some panels using this driver don't provide tcon/cdi/pwr/softstart
values in their reference code. It is normally expected that the right
values will be loaded from OTP in such cases. Make these values
optional to support such panels.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Introduce a generated Kconfig.dts that sets a Kconfig symbol for
every compatible.
* We set DT_HAS_<compat>_ENABLED if the devicetree has a node with
<compat> enabled. (status is okay...)
We can then use the Kconfig symbol in driver Kconfig to determine
if the driver should be available, and thus enabled by default.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Any project with Kconfig option CONFIG_LEGACY_INCLUDE_PATH set to n
couldn't be built because some files were missing zephyr/ prefix in
includes
Re-run the migrate_includes.py script to fix all legacy include paths
Signed-off-by: Tomislav Milkovic <milkovic@byte-lab.com>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
