Move the baud rate selection for uart_console into Kconfig.
This allows apps to specify custom speed. Default is 115200
which should be supported by almost all RS232 and USB adapters
out in the past few years.
Change-Id: I78649bf2a1b2ddfc90a20d611a6454e3ad3b1b3a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This is the final step to convert serial to the new driver model.
The dev->driver_api is now being used by individual drivers.
As a side effect, it is now possible to build multiple serial
drivers in the final image (though it won't make much sense).
Change-Id: I5d864e6503a5431b29006c311320155adf81cf5b
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This introduces the config option CONFIG_UART_CONSOLE,
and also CONFIG_CONSOLE. The UART console can finally
be disabled if desired.
The defconfigs are also being updated.
Change-Id: I5ebaf6471986deca105971e67fcddb43374de94a
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
With this, the UART console has its own initialization which is not
dependent on UART init routines.
This will allow the app to utilize all UARTs for other purposes,
instead of always reserving one for console. Future patch
will enable this choice.
Note that the console init is effectively demoted to pure_init
from pure_early_init. The UART console depends on UART being
initialized, but there is no deferred init at this point.
So this initializes the console a bit later than UARTs,
simply to make sure the UART is initialized before using it.
Once there is a mechanism for some type of deferred initialization,
the UART console init can be promoted back to pure_early.
Change-Id: Iba95197b13384cb1a46e34c78638348b7a0bec8c
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This restructures the device structs and now utilizes the new
driver initialization model. This is another step towards
converting the serial driver to the new driver model.
Note that the serial driver does not initialize the hardware
unless it is being used by another driver. The configuration
of the serial port needs to be done by the driver utilizing
the port (e.g. baud rate, interrupt priority, etc.).
Therefore, some serial ports are declared but not exactly
configured.
Also note that the UART console is being initialized at
the same time as the serial port. This will be removed
in future patch, so the UART console driver will do
its own initialization.
Change-Id: Idd89954b2d0649a557ba8c869ee96512fec898e4
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This encapsulates the whole serial drivers Kconfig sections, and
allows the whole section to be deactivated.
Change-Id: I84f8d35da74f3c00a44d8c17786ea2297422d68b
Signed-off-by: Daniel Leung <danielcp@gmail.com>
This moves the static device definition from the driver file,
drivers/bluetooth/uart.c, into the platform config files for
each platform.
This is another step towards converting UART drivers to
the new driver model. Also, platform config files are a more
logical place for the definition.
Change-Id: I668a52de5a38005b8b2bcb67d74437ead377cb16
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
... instead of an array index to a global array. This is
an intermediate step to make the drivers conform to
the new driver model.
This only changes from using a direct array index to using
device structs. The UARTs are still staticlly defined.
Later patches will make the drivers utilize the driver
initialization procedure specified by the driver model.
Change-Id: I18041bbb4b0efdf8ae87088fd000b391d0827e9b
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The new names reflect better what the functions do: they find the first
bit set starting from the least or most significant bit, i.e. they find
the least or most significant bit set, in a 32-bit word.
Change-Id: I6f0ee4b543f6f37c2f08f7067e14e039c92a6f6a
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Standardize on using the find_[first|last]_set (non-inline) symbols
everywhere.
The non-inline versions provide absolutely no benefits, so they will be
removed in a subsequent commit, and the inline versions will have their
_inline suffix removed.
Change-Id: I5b3dee33ffe3878a05e1bb3c6400a8d8c1640ad4
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Use doxygen format for file documentation and move
parameters to be part of the function comments.
Change-Id: I01c0614e7cd3ef4c689d2aec3aa3e52e0d21ffcd
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Removes the non-PIC disabling PIC code as the PIC is not a supported interrupt
controller. The PIC disabling code remains as it is needed to prevent the
generation of spurious interrupts from the PIC (see CONFIG_SHUTOFF_PIC).
Change-Id: Ic59aa17ab96f34685a5d7b5f24cab391de47edca
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
The PIT is an unsupported device. On x86 based platforms, the LOAPIC_TIMER and
HPET_TIMER are the only supported timers.
Change-Id: Ic890838c811b7eb62008aef0c8a92786f1579217
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Removes the LOAPIC and IOAPIC macros from board.h as they are no longer
appropriate since Kconfig options exist to use in their stead.
Change-Id: I2ce41a7a08d1859682389f35cd5a97c0e2cd5bf7
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Creating the IOAPIC and LOAPIC Kconfig options permits future commits to remove
those settings from the relevant board.h files.
Change-Id: Ie33c703f39c68d6e251d67b1c7cf75a0dd56a7e6
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Removes the LOAPIC timer macros from board.h as they are no longer required
since appropriate Kconfig options exist to use in their stead.
Change-Id: Id0b509eba7cce1839b400f95b989bf886322e1a8
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Creating the LOAPIC timer Kconfig options permits future commits to remove
those settings from the relevant board.h files.
NOTE: No defconfig files have been modified as the LOAPIC_TIMER configuration
option is not enabled in any of them.
Change-Id: I7d97ed089cd4b734566b698183be95d3a166d71f
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Fixes a copy-paste error that inadvertently had the LOAPIC timer being
referred to as the PIT.
Change-Id: I4760d150cd6feb76b7d7384845898c6276bace83
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
For as long as the IOAPIC and LOAPIC code is coupled (as it currently is),
enabling LOAPIC must select IOAPIC to be enabled as well. If future commits
separate the two, then the "select IOAPIC" can be dropped.
Change-Id: Ibe7e6b86e5add19b8b3cc68ebecce760d8914c86
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Removes the HPET timer macros from board.h and uses the HPET timer Kconfig
options in their stead.
Change-Id: Ia0b3cd87716277ac25f12deb31d5c5934f355050
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Adds additional Kconfig options to the HPET timer for setting its base address,
IRQ, IRQ priority and condition for triggering an interrupt.
Change-Id: I80349c60237380129da9ef41ccf6850c6b874c3c
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
All driver Makefiles are adding the same cflags and they
have been done inconsistenly, make all drivers inherit
from the top level Makefile and remove unused includes.
Change-Id: Ie66d0ba7a418ac26f7eb709f50c887dc682e935c
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The name of the device is SYSTICK. The device name should be part of the
file name, like all other timer drivers we support. The name
'cortex_m_timer' said nothing about which device the driver is for, since
it's way too generic: it could be for any timer present on any Cortex-M
board.
Change-Id: I39b4f79c32516ec9aff82c55c0ca639fad1b52bb
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The Zephyr kernel must always be built as a monolithic image, not as
separate nanokernel and microkernel images.
Change-Id: I44fdd2349b32f409c84710f58bc4b3fe96fd79b7
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Removes references to obsolete BSP terminology. Where appropriate, replaces it
with platform terminology.
Change-Id: Ifb17f98bc12d3a28198810351629a109abdc18a5
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Qemu implements HPET so that it is connected to IRQ 2, which makes
necessary to use it in legacy emulation mode.
Add legacy emulation mode to HPET driver.
Change the way the HPET driver is initialized. QEMU requires that
the mode (one shot or periodic) gets set prior loading comparator
value.
Add debugging mode to HPET driver to ease the next port.
Change-Id: I668325d5968451585519a08b6c41863cf6e37f88
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Disable the PIC upon initialization to prevent it from
generating spurious interrupts.
Change-Id: I08ba1d00e269e1fd1d32960dcb844e9fa1ccc195
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Fixes the SYS_CLOCK_HW_CYCLES_PER_SEC Kconfig option dependencies such that
it can be overridden by a modified platform configuration file. This is
particularly important for the LOAPIC timer driver as
SYS_CLOCK_HW_CYCLES_PER_SEC is dependent upon the target's CPU/bus frequency.
Change-Id: I0fb49b4c540888cb1988c76e2a711a85e756f82c
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Updates the timer driver dependencies to simplify the selection of a timer
driver. The timer driver menu only lists those drivers that are compatible
with the previously selected interrupt controller.
Change-Id: I5deea315f7c373c6660bacc411c6374e7b0ae84d
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Selection of the IOAPIC requires that the LOAPIC be previously selected.
Change-Id: I13d95d4bb4ff02c1aebb0b5e573cb2b89dbe530b
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
The LOAPIC_TIMER_FREQ Kconfig option is not used.
Change-Id: I919fd2128f667e0b91467cb542041449738dd992
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Changes the the names of the x86 platforms so that they are more generic.
generic_pc -> ia32
quark -> ia32_pci
NOTE: it is expected that the two platforms will eventually be merged into one.
one. At present, the two platforms support different hardware. For example,
the ia32 supports bluetooth whereas the ia32_pci does not, and the ia32_pci
supports both PCI and HPET whereas the ia32 does not.
Change-Id: I8a980aaef55be8c59f7d19ddeb7fafbf11253408
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Improves code consistency by abstracting the architecture directory in the
set of assembly include paths.
Change-Id: I4b3638419a1242cb0628f128c5e3b82c3357d83c
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Change the function signature of _InitHarware() function and rename
the function to a platform specific name now that it will be called
via a function pointer and not by name.
Call the platform *_init() function at PURE_INIT time.
Change-Id: I5168dfea81f406da135d491a2b4a24e8255f418a
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Update microkernel systems to use the new driver initialization model on the
timer driver.
Change-Id: Ida9ef2a395d0dddf4104d490d78b13b11ea3c347
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Update nanokernel systems to use the new driver initialization model on the
timer driver.
Change-Id: I22d8619f56052f094482d73ab34c9d610492d8c0
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Prepares the _sys_clock_driver_init() routine to interface with the new driver
model. To this end, it must accept a pointer to a device structure and return
an integer.
Change-Id: I3c600ce1efb49c0864aae7b09663ca40d6289372
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
The revised name conforms to Zephyr OS naming conventions.
Change-Id: I5bcdaf1df7da9d8ce5787a08b29ead91dd8f24ce
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Removing the parameter to timer_driver() as it is not used.
Change-Id: I09275287eeb541be0dd315056b4f2bc6cbc2573c
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Remove function name from comment and add @brief instead.
Also capitilize first letter.
Change-Id: Ib708b49bf02e5bc89b0066637a55874e659637e0
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Previous comment style used RETRURNS:, use @return to comply
with javadoc style.
Change-Id: Ib1dffd92da1d97d60063ec5309b08049828f6661
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The change replaces multiple asterisks to ** at
the beginning of comments and adds a space before
the asterisks at the beginning of lines.
Change-Id: I7656bde3bf4d9a31e38941e43b580520432dabc1
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use Kconfig to define this variable and remove its
previous definitions from board.h. This will simplify
creation of different variants from a single platform.
Change-Id: I0aaa5aa81dedf096c6d8c1ea2d509c71817336d3
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
