In 92d8329d5b a new DT property was introduced to set the WQ priority
of the instance. The fallback value when the property was not present
was arbitrarily set to <0 PRIO_PREEMPT>.
The problem is that this value is actually changing the behaviour for
the code that is not explicitly setting the DT property, breaking in
some cases the existing code.
Move the default value to <0 PRIO_COOP> to give the old code a
consistent behaviour before and after the 92d8329d5b commit.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Add a GPIO pass-thru map for accessing the full range (0 to 39) of ESP32
GPIO pins by their datasheet number.
GPIOs 0 to 31 are mapped to gpio0 while GPIOs 32 to 39 are mapped to
gpio1.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
This is a follow-up to commit 1a01ca2adf.
Since support for pinctrl has been added to the qdec_nrfx driver,
the related binding can no longer require the `a-pin` and `b-pin`
properties to be defined.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add DT option to configure the data ready interrupt mode.
Latched is the default; pulsed can be enabled through
the drdy-pulsed DT, if desired.
Signed-off-by: Maxime Vincent <maxime@veemax.be>
Add FDS (Filtered Data Type Selection) + High-Pass reference mode support
(FDS in CTRL6, HP_REF_MODE in CTRL7)
Values are configurable through DT per instance.
Signed-off-by: Maxime Vincent <maxime@veemax.be>
fvp-baser-aemv8r has four pl011_uart devices and all of then have
been added in this patch.
only uart0 and uart1 are enabled as default in fvp_baser_aemv8r.dts
Signed-off-by: Huifeng Zhang <Huifeng.Zhang@arm.com>
STM32WB55xG MCUs include 256 KiB of SRAM split into three banks.
The size of the main bank is 192 KiB, and not 96 KiB as it was
specified in the device tree. This commit fixes the issue and
also updates the definition of the NUCLEO-WB55 board, based on
a STM32WB55RG MCU.
Signed-off-by: Thomas Altenbach <taltenbach@witekio.com>
The PWM period cell will soon be required by the pwm_dt_spec facilities,
this patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The binding has no corresponding driver and it is not referenced
anywhere, so drop it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The binding did not define the PWM cells. Only channel and period have
been added as they are the minimum required ones (flags are not supported).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The PWM period cell will soon be required by the pwm_dt_spec facilities.
This patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In order to be consistent with other platforms, include the PWM
dt-bindings by default.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The PWM period cell will soon be required by the pwm_dt_spec facilities.
This patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The period cell will soon be required by the pwm_dt_spec facilities,
this patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In order to be consistent with other platforms, include the PWM
dt-bindings by default.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The PWM period cell will soon be required by the pwm_dt_spec facilities,
this patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The period cell will soon be required by the pwm_dt_spec facilities,
this patch adds it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Include the PWM dt-bindings by default, so that boards can use utilities
like PWM_MSEC() without extra includes. This is a common pattern done
for e.g. i2c or gpio.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The period cell will soon be required by the pwm_dt_spec facilities,
this patch adds it. Note that flags have not been added as they are
optional and not supported anyway.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Introduce has-interrupt-mask-reg DTS property for nxp,pca95xx driver.
This additionnal property allow to specify that the gpio expander has an
interrupt mask register that must be configured by the driver.
This allow to use this driver with PCAL95xx.
This fixes issue #44834.
Signed-off-by: Xavier Chapron <xavier.chapron@stimio.fr>
In order to be consistent with other platforms, include the PWM
dt-bindings by default.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
NXP LPUART IP supports loopback mode, where TX is internally connected
to RX input. Allow setting loopback mode up via the "nxp,loopback" dts
property.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Align the board dts with the recent changes in the "nordic,nrf-sw-pwm"
binding (remove the no longer existing `channel-count` property) and
add a node representing the edge connector for convenient referring
to SoC pins connected to it.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
... and "nordic,nrf-pwm" binding:
- use channel indexes instead of pin numbers in `pwms` properties that
define PWM LEDs
- add the period and flags cells to `pwms` properties in all PWM LED
definitions; use the commonly used period of 20 ms (giving 50 Hz)
as a default setting
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
... to align with what is used in most other PWM bindings.
Update PWM nodes in SoC .dtsi files accordingly.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Align with other PWM drivers and treat the `pwm` parameter (described
ambiguously as "PWM pin") of the `pwm_pin_set_cycles` function as a PWM
channel, not an SoC pin. This will also make the driver consistent with
the `pwm-cells` property definition in the "nordic,nrf-sw-pwm" binding
and with related `DT_PWMS_*` macros.
The change described above requires also providing a way to specify
SoC pins that are to be assigned to the PWM channels. Hence, the commit
introduces in the "nordic,nrf-sw-pwm" binding the `channel-gpios`
property that replaces the `channel-count` one.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Rework bindings documentation to clearly illustrate the role of ahb
(and cpu1) prescaler which defines the actual core clock frequency,
and not only a bus frequency.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use enum to describe the range of allowed MSI values.
This will help to detect configuration issues earlier.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On some parts, it could be required to use steps before applying
highest frequencies.
This was previously done as part of LL_PLL_ConfigSystemClock_FOO
utility functions which are no more used.
Use device tree to mention when this is required and implement it
in stm32_clock_control_init().
Additionally, fix the calls tp LL_RCC_SetAHBPrescaler, which require
use of ahb_prescaler helper.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Introduce a new scheme to define clock bingings on u5.
In a next steps, this new scheme will allow to provide u5 specific
alternate and complementary device clocks.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This new binding allows to work on providing stm32h7 specific
alternate and complementary device clocks.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The pinctrl support made usage of the 'peripheral'
property no longer required.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
those bindings are no more needed since pinmux was
deprecated in favor of pinctrl.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
to support implementation and peripheral usage of the pinctrl
driver API.
Removes deprecated "use-iomux" property from the SPI node.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
