Set the PLL1_Q divider to 6 give a can core clock of 80MHz to
resolve fdcan_clk reception problem because M_CAN requires that
the host clock "APB1" should be higher or equal to the CAN core
clock "PLL1_Q".
Signed-off-by: IBEN EL HADJ MESSAOUD Marwa <marwa.ibenelhadjmessaoud-ext@st.com>
Add necessary overlay and stm32h573i_dk in i2c_target_api test case
to enable the board.
Signed-off-by: IBEN EL HADJ MESSAOUD Marwa <marwa.ibenelhadjmessaoud-ext@st.com>
Enable Transmitter Delay Compensation whenever the data phase timing
parameters allow it.
Fixes: #70447
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add a utility macro for calculating the Transmitter Delay Compensation
(TDC) Offset using the sample point and CAN core clock prescaler specified
by a set of data phase timing parameters.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove the unused "tx-delay-comp-offset" property from the base CAN FD
controller devicetree binding.
Having a static Transmitter Delay Compensation (TDC) offset is useless.
The offset needs to match the data phase timing parameters in order to
properly configure the second sample point when transmitting CAN FD frames
with BRS enabled.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove broken support for Transmitter Delay Compensation from the Bosch
M_CAN backend driver.
Even if this was enabled via Kconfig, the TDC bit in the DBTP register set
during driver initialization is overwritten in can_mcan_set_timing_data(),
turning TDC off.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The Virtual LAN is changed to use the virtual network interfaces.
Add information what changes might be needed because of this.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The gPTP is not suppose to be run on top of VLAN and the
earlier support was just for testing purposes. Remove VLAN
support now after the VLAN overhaul.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The VLAN interfaces are now Virtual type so we need to
collect only the Virtual interfaces and not Ethernet ones.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The VLAN packets are prepared in Ethernet L2 so no need to have
special handling in the driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The VLAN packets are prepared in Ethernet L2 so no need to have
special handling in the driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The VLAN packets are prepared in Ethernet L2 so no need to have
special handling in the driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The VLAN packets are prepared in Ethernet L2 so no need to have
special handling in the driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The VLAN packets are prepared in Ethernet L2 so no need to have
special handling in the driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The VLAN packets are prepared in Ethernet L2 so no need to have
special handling in the driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The VLAN packets are prepared in Ethernet L2 so no need to have
special handling in the driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The VLAN packets are prepared in Ethernet L2 so no need to have
special handling in the driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The VLAN packets are prepared in Ethernet L2 so no need to have
special handling in the driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Virtual LAN logic is now done in Ethernet L2 so no need to manipulate
VLAN packets in the driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Print also network interface index together with the pointer value
in order to get more useful information what is going on in the system.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Print information whether a multicast address is properly
joined to a multicast group when print addresses using
"net iface" command.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
As the interface type is always Virtual, no need to print it.
Print instead the name of the network interface as it is more
useful to the user.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If an IPv6 address was added to the interface while the
interface was down, its solicited node multicast address
is not joined properly and IPv6 communication will to
other hosts will fail. So make sure to rejoin all the
solicited node multicast groups that were joined already
when the network inteface is going up.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add debug information to print when the network L2 enable
callback is called and fails. Useful to see this information
as at that point the interface goes down.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Start any pending IPv6 DAD timers when interface comes up.
If IPv6 addresses have been added to the network interface when
it was down, the addresses would never work properly if the DAD
is not done.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Instead of printing just a network interface pointer, print
also the interface index so debugging is a bit faster as no
lookup from interface listing is needed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
No need to do the checks any more because user has specified
the VLAN count and so many VLAN virtual interface are already
created.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Re-implement the VLAN support inside the network stack.
All the user facing APIs stay as is but internally the VLANs
are implemented using the L2 virtual interfaces.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The SOC name for the `imx8ulp_evk` board has been changed
to `mimx8ud7`. As such, update `deprecated.cmake` to reflect
this change.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
The SOC name `imx8ulp` has been just a placeholder until
support for the SOC's ADSP (since this is the only core
that's supported in Zephyr) could be added to the NXP HAL.
Now that the support has been added, to make use of it, the
SOC name `imx8ulp` has to be changed to `mimx8ud7`. As such,
this commit does the following:
1) Introduces SOC part number configuration - needed
by some HAL headers.
2) Replaces all occurrences of `imx8ulp` (as the SOC
name) with `mimx8ud7`.
3) Enables `CONFIG_HAS_MCUX`.
4) Aligns all `CONFIG_SOC_` configurations with the
new SOC name.
5) Updates SOF hash. This is needed to fix build issues
caused by this name change. This is not done in a separate
commit to preserve bisectability.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
This commit updates the CI workflows to use the CI image v0.26.11, which
includes bsim 2.2 and nrf-regtool 5.1.0.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The thrift hello/client sample did not have the required
kconfig options for some reason.
Adding these seemed to fix the issue.
CONFIG_COMMON_LIBC_THRD=y
CONFIG_DYNAMIC_THREAD=y
CONFIG_THREAD_STACK_INFO=y
Signed-off-by: Chris Friedt <chrisfriedt@gmail.com>
When thread stack is defined as an array, K_THREAD_STACK_LEN()
is used to calculate the size for each stack in the array.
However, standalone thread stack has its size calculated by
Z_THREAD_STACK_SIZE_ADJUST() instead. Depending on the arch
alignment requirement, they may not be the same... which
could cause some confusions. So align them both to use
K_THREAD_STACK_LEN().
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
When kernel stack is defined as an array, K_KERNEL_STACK_LEN()
is used to calculate the size for each stack in the array.
However, standalone kernel stack has its size calculated by
Z_KERNEL_STACK_SIZE_ADJUST() instead. Depending on the arch
alignment requirement, they may not be the same... which
could cause some confusions. So align them both to use
K_KERNEL_STACK_LEN().
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The reserved flash space for coredump is 4KB. However,
the dump_stack itself is larger than 4KB due to kernel stack
size adjustment. So enlarge the space for another page.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
