Fix incorrect note that write only allows to change value of
bit to zero, where proper information is that change is only allowed
from erase-value to the opposite.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The commit adds missing binary or in write operation.
Assuming that program-erase devices only allow switching bits
from erase-value to opposite, in case of 0x00 erase value device
only ones can be written.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
This implements basic driver to utilize the I3C IP block
on NPCX.
1. I3C mode: Main controller mode only.
2. Transfer: Support SDR only.
3. IBI: Support Hot-Join, IBI(MDB).
Controller request is not supported.
4. Support 3 I3C modules:
I3C1(3.3V), I3C2(1.8V, espi mode), (I3C3 1.8V or 3.3V)
Signed-off-by: Alvis Sun <yfsun@nuvoton.com>
During DAA, the responding device might not be in the device list.
This CL adds target device descriptor's pointer checking to prevent
getting unexpected results.
Signed-off-by: Alvis Sun <yfsun@nuvoton.com>
1. The only valid values of MCLKD clock frequency
are between 40Mhz to 50Mhz.
2. If DMA is used, the APB4_CLK clock frequency must
be equal to or higher than 20Mhz.
Signed-off-by: Alvis Sun <yfsun@nuvoton.com>
Found via static analysis. In `can_mcan_state_change_handler`, the
return value of `can_mcan_get_state` is not checked for error. In the
event of an error, both `err_cnt` and `state` are left unitialized and
accessed downstream.
The correct behavior is to return early in that case.
Signed-off-by: François Baldassari <francois@memfault.com>
- Configure a UART TX buffer; the backend would otherwise assert in
its configuration or (if the asserts are off) miserably fail when
trying to send anything to the GNSS modem.
- Fine tune the UART RX buffer size and make it depend on whether
satellite data is received.
- Remove unused k_spinlock.
- Make declaration of Kconfig items dependent on GNSS_NMEA_GENERIC
conditional.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
As of now only the resume action is supported, and doesn't perform
any power action on the GNSS modem.
It allows to initialize the GNSS driver later than it would otherwise
be.
Also, the driver now runs a modem-specific chat script on resumption.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
Those helpers allow to define some typical kinds of chat matches and
scripts with more ease/less boilerplate.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
Fixes overwriting a mailbox before sending it completes.
Overwriting can occur when one thread has waited for
another thread to complete the send function and
fills a mailbox selected based on
the transmit_status_register variable,
which has not been updated after waiting and,
accordingly, does not contain up-to-date information
about the mailboxes used.
Signed-off-by: Mikhail Siomin <victorovich.01@mail.ru>
Remove unnecessary asserts from various CAN controller drivers. These
asserts are all covered by the common CAN subsystem API implementations.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Validate the CAN ID and CAN ID mask used in the can_filter struct before
passing it to the driver.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Mass Storage enumeration failed because udc_stm32_ep_mem_config() was only
increasing priv->occupied_mem on endpoint enable, and not decreasing it on
endpoint disable. Fix the issue by decreasing priv->occupied_mem
on endpoint disable.
Signed-off-by: Arne Bohnsack <arne.bohnsack@draeger.com>
Added write of strobe register after setting long press reset
configuration. This is needed to apply the new value.
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
1. Correct node label in k64 overlay for ptp test
- Not sure if this actually matters since it appears
that actual hardware is no longer tested in net tests
2. Include fsl_enet with <> instead of "".
3. Build the ptp clock driver only if the ethernet driver is built
- Technically I think the 1588 timer should be able to be used
even if the ethernet mac is not used, but I would imagine this
to be an extraordinarily rare, weird, and niche use case, so to fix
the current CI error caused by net test disabling ethernet drivers,
couple the ptp clock driver to the ethernet driver in the build
configuration.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Negative error codes cannot be returned if the function returns an
unsigned integer. Change function's API to return the read compare
register value through a pointer and the actual result as a signed
integer.
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
We are not able to achive 50ppm on nRF54L.
Working on fixing it propperly, but untill we do set what we get.
Signed-off-by: Martin Tverdal <martin.tverdal@nordicsemi.no>
add gpio_intel driver with acpi based resource enumeration support.
Also updated test cases overlay with new dts entires.
Signed-off-by: Najumon B.A <najumon.ba@intel.com>
The commit "drivers: ethernet: dsa_ksz8xxx: use
NET_DEVICE_DT_DEFINE_INSTANCE"
(SHA1: f78a081066) replaced
NET_DEVICE_INIT_INSTANCE() with NET_DEVICE_DT_DEFINE_INSTANCE() to
facilitate the removal of deprecated (from Zephyr's 3.2 release)
DT_LABEL() macro.
Unfortunately, the per LAN port initialization is necessary for correct
operation of the DSA driver - otherwise following errors were visible
when LLDP DSA sample (samples/net/dsa/src) was run on ip_k66f board:
<wrn> net_if: iface 0x20001440 is down
<inf> net_dsa_lldp_sample: LLDP pkt recv -> lan1
<inf> net_dsa_lldp_sample: CHASSIS ID: 38:05:43:69:XX:ZZ
<inf> net_dsa_lldp_sample: PORT ID: 38:05:43:69:XX:ZZ
<inf> net_dsa_lldp_sample: TTL: 120s
<inf> net_dsa_lldp_sample: SYSTEM NAME: mtt
<err> net_dsa_lldp_sample: Failed to send, errno 115
The fix is to use again NET_DEVICE_INIT_INSTANCE() with "lan"X name
assigned (to avoid too long names when recommended DT_PROP() is
used instead of DT_LABEL()).
Fixes: f78a081066
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add an I3C shell. This includes support of all I3C CCC commands that
currently have helper functions implemented. This also includes all
the read/write shell commands that the i2c shell supported. An Info
command is also provided which will print out all i3c and i2c info
of an i3c bus. Only SDR read/writes are currently implemented.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Updates the linker script fragments under 'drivers' to use
Z_LINK_ITERABLE_SUBALIGN for the subalignment instead of
a hardcoded value of 4.
Signed-off-by: Peter Mitsis <peter.mitsis@intel.com>
This commit removes unnecessary usage of the `ARG_UNUSED` macro and
unnecessary initialization of the `ret` variable where its value is
guaranteed to be overwritten by subsequent operations.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Interrupt handlers are expected to have a pototype
void (const void*)
but nrfx_grtc_irq_handler has just a void(void)
(with no input parameter).
Fix it by using a trampoline.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
FTM internal counter can be clocked by one of three clock sources
independent of the module bus clock. This patch introduces a DT property
to perform the clock selection from DT.
DT sources are updated to keep the current clock selection for all boards,
with exception of ucans32k1sic board which is migrated to use system
clock by default, as this seems to be a better choice for most cases.
Some PWM LED samples require slower clock so overlays are added for
those cases.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
There is no reason to pass addrlen by pointer, since it is a read-only in
the context of sockaddr_to_nsos_mid().
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Add support for half-duplex (3-wire) SPI operation using the Raspberry
Pi Pico PIO. To allow control of the size of the driver, including
half-duplex support is optional, under the control of Kconfig options.
The original PIO source code is also included as a reference.
Corrected 3-wire tx/rx counts.
Enable half-duplex code based on DTS configuration
Replace runtime checks with static BUILD_ASSERT()
Remove too-fussy Kconfig options
Removed PIO source per review request
Signed-off-by: Steve Boylan <stephen.boylan@beechwoods.com>
Redundant kLPSPI_MasterPcsContinuous transfer config flag
is eliminated since this is set earlier.
Signed-off-by: Dipak Shetty <dipak.shetty@zeiss.com>
Submit USBFSOTG_EVT_XFER on halt clear to allow queued
transfers to execute as soon as endpoint STALL is cleared.
Signed-off-by: Mark Wang <yichang.wang@nxp.com>
Make DSA dependent on ETH_DSA_SUPPORT which is selected by driver
kconfigs, rather than having a list of dependencies.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
