703021a78a
This commit updates the NS board variant from `nrf9160dk_nrf9160ns` to `nrf9160dk_nrf9160_ns` to maintain consistency across zephyr. Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
68 lines
2.2 KiB
Plaintext
68 lines
2.2 KiB
Plaintext
# nRF9160 DK NRF9160 board configuration
|
|
|
|
# Copyright (c) 2018-2020 Nordic Semiconductor ASA
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
|
|
if BOARD_NRF9160DK_NRF9160 || BOARD_NRF9160DK_NRF9160_NS
|
|
|
|
config BOARD
|
|
default "nrf9160dk_nrf9160"
|
|
|
|
# By default, if we build for a Non-Secure version of the board,
|
|
# force building with TF-M as the Secure Execution Environment.
|
|
|
|
config BUILD_WITH_TFM
|
|
default y if BOARD_NRF9160DK_NRF9160_NS
|
|
|
|
if BUILD_WITH_TFM
|
|
|
|
# By default, if we build with TF-M, instruct build system to
|
|
# flash the combined TF-M (Secure) & Zephyr (Non Secure) image
|
|
# (when building in-tree tests).
|
|
config TFM_FLASH_MERGED_BINARY
|
|
bool
|
|
default y if TEST_ARM_CORTEX_M
|
|
|
|
endif # BUILD_WITH_TFM
|
|
|
|
# For the secure version of the board the firmware is linked at the beginning
|
|
# of the flash, or into the code-partition defined in DT if it is intended to
|
|
# be loaded by MCUboot. If the secure firmware is to be combined with a non-
|
|
# secure image (TRUSTED_EXECUTION_SECURE=y), the secure FW image shall always
|
|
# be restricted to the size of its code partition.
|
|
# For the non-secure version of the board, the firmware
|
|
# must be linked into the code-partition (non-secure) defined in DT, regardless.
|
|
# Apply this configuration below by setting the Kconfig symbols used by
|
|
# the linker according to the information extracted from DT partitions.
|
|
|
|
# Workaround for not being able to have commas in macro arguments
|
|
DT_CHOSEN_Z_CODE_PARTITION := zephyr,code-partition
|
|
|
|
config FLASH_LOAD_SIZE
|
|
default $(dt_chosen_reg_size_hex,$(DT_CHOSEN_Z_CODE_PARTITION))
|
|
depends on BOARD_NRF9160DK_NRF9160 && TRUSTED_EXECUTION_SECURE
|
|
|
|
if BOARD_NRF9160DK_NRF9160_NS
|
|
|
|
config FLASH_LOAD_OFFSET
|
|
default $(dt_chosen_reg_addr_hex,$(DT_CHOSEN_Z_CODE_PARTITION))
|
|
|
|
config FLASH_LOAD_SIZE
|
|
default $(dt_chosen_reg_size_hex,$(DT_CHOSEN_Z_CODE_PARTITION))
|
|
|
|
endif # BOARD_NRF9160DK_NRF9160_NS
|
|
|
|
config BT_HCI_VS
|
|
default y if BT
|
|
|
|
config BT_WAIT_NOP
|
|
default BT && $(dt_nodelabel_enabled,nrf52840_reset)
|
|
|
|
# Workaround for not being able to have commas in macro arguments
|
|
DT_COMPAT_NXP_PCAL6408A := nxp,pcal6408a
|
|
|
|
config I2C
|
|
default $(dt_compat_on_bus,$(DT_COMPAT_NXP_PCAL6408A),i2c)
|
|
|
|
endif # BOARD_NRF9160DK_NRF9160 || BOARD_NRF9160DK_NRF9160_NS
|